Answers
this looks like its the different phases of a single cylinder 4 stroke engine what are you doing in the picture or assignment though matching the numbers to the descriptions on the side?
Related Questions
1. A drawing of a cabinet shows that its dimensions are 9cm. by 4cm. The drawing indicates 1:50 scaling. What are the actual dimensions of the cabinet?
2. Bongbong is tasked to draw a floor plan with a scale of 1:100. If the total length of the actual house is 8 meters, what will be its corresponding measurement in centimeters in floor plan?
3.The length of a bedroom measures 2.5 m., what will be the measurement in centimeters to be used in the drawing if it is in 1:50 scale?
Answers
Explanation:
This means that for every 1 cm on the drawing, there is 80 cm in reality. To put it another way, take this
1:80 means that the building is 80 times the size of the drawing
80:1 means that the drawing is 80 times the size of the building
If it were 80:1, the drawing itself would be over 100m long.
Your vehicle is/ are not part of regulated safety system 
Answers
Answer:
Amends the FMVSS on air brake systems to improve the stopping distance performance of truck tractors. The rule requires the vast majority of new heavy truck tractors to achieve a 30 percent reduction in stopping distance compared to currently required levels. For these heavy truck tractors (approximately 99 percent of the fleet), the amended standard requires those vehicles to stop in not more than 250 feet when loaded to their gross vehicle weight rating (GVWR) and tested at a speed of 60 miles per hour (mph). For a small number of very heavy severe service tractors, the stopping distance requirement will be 310 feet under these same conditions. In addition, this final rule requires that all heavy truck tractors must stop within 235 feet when loaded to their “lightly loaded vehicle weight” (LLVW).
Amends the FMVSS on air brake systems to improve the stopping distance performance of truck tractors. The rule requires the vast majority of new heavy truck tractors to achieve a 30 percent reduction in stopping distance compared to currently required levels. For these heavy truck tractors (approximately 99 percent of the fleet), the amended standard requires those vehicles to stop in not more than 250 feet when loaded to their gross vehicle weight rating (GVWR) and tested at a speed of 60 miles per hour (mph). For a small number of very heavy severe service tractors, the stopping distance requirement will be 310 feet under these same conditions. In addition, this final rule requires that all heavy truck tractors must stop within 235 feet when loaded to their “lightly loaded vehicle weight” (LLVW).
Answer:
power window controls
Explanation:
Which of the following most accurately describes an institutional conflict of interest?
Answers
Answer:
Defined as a situation in which the financial investments or holdings of Stanford University or the personal financial interests or holdings of institutional leaders might affect or reasonably appear to affect institutional processes for the design, conduct, reporting, review, or oversight of human subjects research.
In a pipe of diameter 350 mm and length 75m water is flowing at a velocity of 2.8 m/s. Find the head lost due to friction by using Darcy Weisbach equation?
Answers
Answer:
1.71 m
Explanation:
The attachment shows the equation and values used in it. The Moody Friction Factor is not specified in this problem statement, so we have used the value provided by the calculator web site (0.02). The head loss is proportional to that factor, so it is not difficult to find the loss if your factor is different.
1. Plot the normal and shear components of stress on the fictitious element relative to (1) Cartesian coordinator system, (2) a cylindrical coordinator system, and (3) a spherical coordinate system. Note: Your drawing should be by hand and in a 3D manner. Write the stress notation in matrix form for three coordinator systems. Explain the biological motivations for using the above three coordinator systems.
Answers
Answer:
d
Explanation:
1. The reference OSHA standard requires several important characteristics of a PFAS:
It must limit the maximum arresting force imparted to the body to
with the full
body harness.
Answers
The reference OSHA standard requires several important characteristics of a PFAS. The employer must ensure that personal fall arrest systems (PFAs) must:
a. Limit the maximum arresting force on the employee to 1,800 pounds (8 kN). The figure used above must be based on the use of a full body harness.
Maximum arresting force is the highest amount of force that the fall protection system and the individual attached to the system will face as gotten by the deceleration device.OSHA regulations gives the system performance criteria for a personal fall arrest system.
From the above, we can therefore say that The reference OSHA standard requires several important characteristics of personal fall arrest systems (PFAs) as employers must reduce the maximum arresting force on the employee to 1,800 pounds (8 kN) using full body harness.
Learn more
https://brainly.com/question/15049508
The mechanical energy of an object is a combination of its potential energy and its
Answers
The mechanical energy of an object is a combination of its potential energy and its kinetic energy.
4. When welding, the practice metal is called a
Answers
Answer:
Nonstandard
Explanation:
Tech a says both oem and tcmc brake pad kits come with new shims. Tech b says tcmc products have a 13 digit part number instead of the traditional 10 digits. Who is correct?
Answers
A gas turbine power plant is being designed using an air-standard Brayton cycle. Air enters the compressor with a volumetric flow rate of 7 m3 /s at 100 kPa, 300 K. The turbine inlet temperature is expected to be 1400 K. The compressor pressure ratio is 10. The turbine exhaust goes back to the atmosphere at 100 kPa. (a) Draw the schematic and T-s diagrams. (b) Determine the thermal efficiency. (c) Determine the back work ratio of this power plant.
Answers
check all the photos