technician a says a defective pcv valve may cause rough idle operation. technician b says the pcv system depends upon a properly sealed engine to perform correctly. who is correct?

Explanation:

Now we change into rectangular form

=40 cos (36.9°) +j 40 sin (36.9°) VA

=31.9+J24VA

Hence, correct option (31.9 +j 24) VA

Answer:

I am from Nepal where are you from

Explanation:

Solving for the capacitive reactive power, we have

Qc = 8,500 (tan(-cos (0.85)) - tan(-cos¹ (0.97)))

Qc = -3137.5261 = -3138 KVAR

Based on the information provided, the technician who is correct is: B. Technician B.

A braking system can be defined as a mechanical system which comprises various components that are designed and developed to bring an automobile vehicle in motion to a stop, when applied by a driver.

In order for a technician to diagnose a brake system, the following symptoms should be adequately and appropriately checked and used by the technician:

Based on the information provided, we can reasonably infer and logically deduce that the technician who is correct is Technician B because brake shoes are to be replaced in axle sets.

Read more on braking system here: https://brainly.com/question/24751467

#SPJ1

Complete Question:

Tech a says that brake shoe linings saturated with brake fluid from a leaky wheel cylinder can be cleaned with brake cleaner and reused as long as they aren’t worn out. tech b says that brake shoes should be replaced in axle sets. who is correct?

Technician A.

Technician B.

Neither Technician A nor Technician B

Both Technician A and Technician B

Which is the engineering name of the complicated circuit board in EC circuits?

Answer:

PCB (Printed Circuit Board)

Explanation:

Construction:

Initially, this board is an insulator plate. A circuit diagram is clearly drawn by a computer and scanned.

This plate is put under a multipurpose printer and the circuit is printed onto the plate with conductive copper tiny plates and wires.

Since tech A says that black exhaust indicates a very rich-running engine is false and since tech b says that white exhaust can indicate coolant in the exhaust, Tech B  is correct.

Black exhaust smoke is known to be one that can show up if the vehicle is said to be burning too much fuel.

Note that this situation could be as a result of  a clogged air filter, the malfunctioning of the fuel injection system, a blocked manifold, or other forms of issues.

Therefore, Since tech A says that black exhaust indicates a very rich-running engine is false and since tech b says that white exhaust can indicate coolant in the exhaust, Tech B  is correct.

Learn more about exhaust from

https://brainly.com/question/12741044
#SPJ1

Answer:

1) The bending moment diagram of the shaft is shown in Figure 1. The weakest cross section A is located at the point where the bending moment is maximum.

2) The weakest point on cross section A is located at the point where the bending moment is maximum.

3) The von-Mises stress at the weakest point is given by:

σ = M/I

where M is the bending moment and I is the moment of inertia of the cross section.

4) The factor of safety n is given by:

n = Sy/σ

where Sy is the yield strength of the shaft and σ is the von-Mises stress at the weakest point.

Explanation:

Hope this helps!

Construction Classification is the classification of a building or structure into one of the five types or subtypes included in the model building codes, based on types of materials and structural protection afforded.

A building can be defined as a structure which has a roof and a wall a building is a permanent structure which has a base and a very study materials which are being used to create a stable structure with a foundation.

Construction classification can be defined as type of building construction which is being legalized by the people. These the building reduces that quality damages also it provides a safe and sound structure with is often guarded.

Learn more about building, here:

https://brainly.com/question/6372674

#SPJ1

Explanation:

Note that the working equation that converts a complex number from rectangular to phasor form is given by

a+bi=r 20

Hence, the equivalent in phasor form is 87.46<149.04°

The number of threads in 16 inches of the rod is 176 threads

Given that:

1 threaded rod= 11 threads per inch

Therefore, to find the number of threads in 16 inches of the rod,

We would have to multiply and this is given below:

16 * 11= 176 threads

This answer is gotten because a threaded rod has 11 threads per inch and when there are 16 inches of rod, to find the number of inches, you would have to multiply the values together.

Read more about calculations here:

https://brainly.com/question/2005046

#SPJ1

Answer:

I say C

Explanation:

Answer:

Given, diameter of pin head d = 1 mm = 1/25.4 = 0.0394 in Surface area of a pinhead, A = 4pr^2 =

Explanation:

eesh