The usage of the wet bulb thermometer is important to measure the relative humidity or the air.
How to explain the temperature?It should be noted that air can be saturated with different amount of water vapors according to its temperature.
The percentage of water vapor with the amount of water at the temperature is the relative humidity. Based on the question, the salad oil is important rather than using water since oil doesn't evaporate.
Learn more about temperature on:
https://brainly.com/question/24746268
A 1. 5-kω resistor and 27. 7-mh inductor are connected in series to a vrms = 120 v ac power source oscillating at a frequency of f = 60 hz. The voltage as a function of time is given by
The voltage as a function of time for the power source oscillating at the given frequency is determined as V = 169.7sin(120πt).
Peak voltageThe peak voltage of the source is calculated as follows;
Vrms = 0.7071V₀
120 = 0.7071V₀
V₀ = 120/0.7071
V₀ = 169.7 V
Angular frequency of the waveω = 2πf
where;
f is frequency = 60 Hz
ω = 2π x 60
ω = 120π rad/s
Voltage equation as function of timeV = V₀sin(ωt)
V = 169.7sin(120πt)
Learn more about peak voltage here: https://brainly.com/question/6249123
The voltage equation is a function of a time is V = 169.7sin(120πt) if the 1. 5-kω resistor and 27. 7-mh inductors are connected in series to a vrms = 120 v ac power source oscillating at a frequency of f = 60 Hz.
What is induced voltage?Electromagnetic induction causes the induced voltage. Electromagnetic induction is the process of creating emf (induced voltage) by exposing a conductor to a magnetic field.
We have:
[tex]\rm V{rms} = 120[/tex]
We know:
[tex]\rm V_{rms} = 0.7071V_o[/tex]
[tex]\rm 120 = 0.7071V_o[/tex]
[tex]\rm V_o = 169.70[/tex] Volts
Expression for the angular frequency is given by:
ω = 2πf
Where f is frequency
ω = 2π x 60
ω = 120π rad/s
Voltage equation as a function of time is given by:
V = V₀sin(ωt)
V = 169.7sin(120πt)
Thus, the voltage equation is a function of a time is V = 169.7sin(120πt) if the 1. 5-kω resistor and 27. 7-mh inductors are connected in series to a vrms = 120 v ac power source oscillating at a frequency of f = 60 Hz.
Learn more about the induced voltage here:
brainly.com/question/19482771
#SPJ4
A book on a shelf 2.5 m above the floor has a mass of 1.7 kg. What is the gravitational potential energy of the book?
Answer:
42.5J (If g = 10)
41.6925J (If g = 9.81)
41.67975J (If g = 9.807)
Explanation:
Gravitational Potential Energy = Mass X Height X Gravitaitonal Field
Earth's Gravity is = 9.807 m/s^2
It is often rounded to 9.81 or 10
What current is required in the windings of a long solenoid that has 1580 turns uniformly distributed over a length of 0.44 m in order to produce a magnetic field of magnitude 0.000394 T at the center of the solenoid
The current required in the windings of the given long solenoid that has 1580 turns uniformly distributed over the length of the solenoid is 1.98 A.
Magnetic field at the center of a solenoidThe magnetic field at the center of a solenoid is given by the following formula,
B = μ₀nI
where;
μ₀ is permeability of free space n is number of turnsI is current in the solenoidCurrent in the solenoidI = B/μ₀n
I = (0.00394) / (4π x 10⁻⁷ x 1580)
I = 1.98 A
Thus, the current required in the windings of the given long solenoid is 1.98 A.
Learn more about current in solenoid here: https://brainly.com/question/17086348
How many stars are in a typical spiral galaxy, like our own?.
Answer:
200 billion to 400 billion stars in a typical spiral
Explanation:
hope this helps
have an awesome day -TJ
a car starts from the rest and accelerates at 9.54m/s for 6.5 seconds. what is the distance covered by the car
Answer:
= 201.53 meters
Explanation:
A car started from rest and accelerated at 9.54 m/s^2 for 6.5 seconds. How much distance was covered by the car?
Use the formula d = [tex]\frac{at^{2} }{2} ,[/tex]
where d is the distance, t is the time and "a" is the acceleration.
[tex]d=\frac{9*54*6*5^{2} }{2} = 201.53 m[/tex]
What do we call objects that form like a star (from a contracting gas cloud), but do not have enough mass to ignite hydrogen fusion in their centers
A brown dwarf is a starlike body that do do not have enough mass to ignite hydrogen fusion in their centers.
What is a brown dwarf?Brown dwarf refer to a body of substellar that is not huge or big enough to undergo nuclear fusion of o hydrogen into helium in their cores. This formed when there is contraction of gases in the intercellar spaces. The have a mass between 13 to 80 times that of Jupiter.
Therefore, brown dwarf is a starlike body that do don't not have enough mass to ignite hydrogen fusion in their centers.
Learn more about brown dwarf below.
https://brainly.com/question/15722167
Complete the mechanism for the given decarboxylation by adding any missing atoms, bonds, charges, nonbonding electrons, and curved arrows
The decarboxylation reaction involves the removal and replacement of a carboxyl group with hydrogen.
What is a decarboxylation reaction?A decarboxylation reaction is one in which the carboxyl group in a carboxylic acid is replaced with hydrogen.
In living organisms, decarboxylation reactions are catalyzed by enzymes called decarboxylases or carboxy-lyases.
The decarboxylation of beta-carbonyl esters proceeds through a cyclic transition state giving an enol intermediate which then tautomerises to the carbonyl.
Therefore, a decarboxylation reaction involves the removal and replacement of a carboxyl group with hydrogen.
Leran more about decarboxylation at: https://brainly.com/question/893601
The decarboxylation reaction is given with the removal of the carbon dioxide from the carboxyl group.
What is carboxyl group?The carboxyl group is the attachment of the OH and the =O functional group to the carbon atom.
In the decarboxylation reaction, there has been the removal of the carbon dioxide and the carboxyl group is replaces with the Hydrogen atom.
The decarboxylation reaction for the given reactant with the missing groups is given in the image attached.
Learn more about carboxyl group, here:
https://brainly.com/question/14769767
#SPJ4
Rectangular plate has a voltage of +180V and plate to the first plate) has a 'voltage of -5V. Determie another rectangular plate (parallel to between these two plates? The distance of the field strength at any point separation of the plates is finite, say 8.6mm.
For a Rectangular plate has a voltage of +180V and a 'voltage of -5V. , the second plate has the Electric field mathematically given as
E=21.5*10^3v/m
What is the field strength?Generally, the equation for the Electric field is mathematically given as
E=v/d
Where
v={180-(-5)}v
v=185v
Therefore
E=185/8.6*10^{-3}
E=21.5*10^3v/m
In conclusion, Electric field
E=21.5*10^3v/m
Read more about electric field
https://brainly.com/question/9383604
The car's motor transfers
-----------energy
into useful-----------
energy as the car moves,
Some energy is wasted -----------as
energy
Answer:
chemical potential
kinetic
thermal
A wave has a speed of 3.4m/s, if its frequency is 2.5 (Hz). What is the wavelength. Equation:
Speed= wavelength x frequency (Hz)
A. 25m
B. 10m
C. 1.36m
D. 0.73m
Answer:
1.36 meters
Explanation:
we just plug in the values into the formula given in the question
3.4/2.5 = answer
answer is 1.36
On average, what is the thickness of the milky way as seen from earth, measured in degrees?.
Answer:
20-30 degree
Explanation:
the milky is around 20_30 degrees thick in the cygnus region when overhead on a decent night
One billiard ball strikes another billiard ball, and they move away from each other
at a 90° angle. The momentums involved include (blank) of the velocity before and after the collision.
(A) only the direction
(C) the magnitude and direction
(B) only the magnitude
(D) the square of the magnitude
Answer:
C) The magnitude and direction
Explanation:
Velocity is a vector quantity, meaning that it has both magnitude and direction.
For the momentum, we look at both the direction of the ball (negative, positive) and the magnitude of the velocity (5 m/s, 10 m/s) when figuring out what to use for "v" in p = mv.
Distinguish between pressure and force in the case of wang yourself on a common bathroom scale
Answer: hey here's your answer...
Explanation: We can think of a force as a push on a surface, such as the force due to gravity you exert when standing on a bathroom scale. Pressure involves the distribution of force. The scale measures force, not pressure, so your weight reading is the same no matter how you distribute your weight on the scale.
Hope this helps...
Have a nice day-
18. Students are discussing the magnitude of the electrostatic force that sphere B exerts on sphere A.
Eva states that sphere B exerts a larger electrostatic force on sphere A than sphere A does on sphere B.
. Taylor states that sphere B exerts the same electrostatic force on sphere A as sphere A does on sphere B.
• Jac states that sphere B exerts a smaller electrostatic force on sphere A than sphere A does on sphere B.
Which student is correct? Give scientific reasoning to support your decision.
she is k bads boy (into negative)
Give two examples that provide evidence for the presence of terrestrial magnetism?
Explanation:
When a magnetic body is buried inside the earth in North-South direction, it gets magnetized due to the effect of terrestrial magnetism. A freely suspended magnet faces North-South direction.
Which image corresponds to what moment in time? (1 point) The low-pitched sound corresponds to the sound source getting closer, its wavelength is longer. The high-pitched sound corresponds to the sound source moving away, its wavelength is shorter. The low-pitched sound corresponds to the sound source moving away; its wavelength is shorter. The high-pitched sound corresponds to the sound source getting closer; its wavelength is longer. The low-pitched sound corresponds to the sound source getting closer, its wavelength is shorter. The high-pitched sound corresponds to the sound source moving away, its wavelength is longer. The low-pitched sound corresponds to the sound source moving away, its wavelength is longer. The high-pitched sound corresponds to the sound source getting closer, its wavelength is shorter.
Answer:
The low-pitched sound corresponds to the sound source moving away; its wavelength is longer. The high-pitched sound corresponds to the sound source getting closer; its wavelength is shorter.
Just took the quiz, and it said this answer was correct.
In this picture, The low-pitched sound corresponds to the sound source moving away; its wavelength is longer. The high-pitched sound corresponds to the sound source getting closer; its wavelength is shorter.
What is wave ?Wave is is a disturbance in a medium that carries energy as well as momentum . wave is characterized by amplitude, wavelength and phase. Amplitude is the greatest distance that the particles are vibrating. especially a sound or radio wave, moves up and down. Amplitude is a measure of loudness of a sound wave. More amplitude means more loud is the sound wave.
Wavelength is the distance between two points on the wave which are in same phase. Phase is the position of a wave at a point at time t on a waveform.
There are two types of the wave longitudinal wave and transverse wave.
Longitudinal wave : in which, vibration of the medium (particle) is parallel to propagation of the wave. Sound wave is a longitudinal wave.
Transverse wave : in which, vibration of the medium (particle) is perpendicular to propagation of the wave. Light wave is a Transverse wave.
According to the Doppler's effect, a sound source moves away from the observer its wavelength increases and when it moves towards the observer the wavelength decreases.
To know more about Doppler's effect :
https://brainly.com/question/15318474
#SPJ2.
Which level instruments operate on the principle of generating a signal and then measuring the time required for the signal to reflect off the process fluid back to the transmitter
One of the most crucial devices for electronics and communication is the signal generator. For several reasons, including testing, debugging, and designing, it is utilized to produce various types of signals and frequencies.
What instruments operate principle of generating a signal?Engineers create electronic signals using signal generators, which can be analogue or digital, to test circuit designs. Signal generators come in a wide variety of forms with various characteristics and uses. The most typical signal generator kinds and their distinctive qualities are listed below.
Therefore, radar level instruments operate on the principle of generating a signal and then measuring the time required for the signal to reflect off the process fluid back to the transmitter.
Learn more about instruments here:
https://brainly.com/question/29608809
#SPJ2
A dense mix of dry, hot rock fragments and hot gas erupting from volcanic vents at high speed is pyroclastic flow. lahar. fumarole. tephra.
Magma is called for the dense mix of dry hot rock fragments and hot gas erupting from volcanic vent at high speed.
What is magma?Magma is the extremely hot liquid and flows under the surface of the earth. When this liquid comes out to the surface of earth, then called as lava.
Gas bubble, making up to lave are energetic in nature, because they keep on expanding in all directions, they will go all out to the only open are of a volcano, the vent, in an upward direction.
Hence Magma is called for the dense mix of dry hot rock fragments and hot gas erupting from volcanic vent at high speed.
To know more about magma follow
https://brainly.com/question/23661578
Scientists predict that in another 250 million years, the continents will be located in different positions. How is this possible? *
Answer:
The continents will be in different positions because tectonic plate boundaries are always moving.
At an altitude of 6,500 feet MSL, the current altimeter setting is 30. 42" Hg. The pressure altitude would be approximately
At an altitude of 6,500 feet MSL and with the current altimeter setting is 30. 42" Hg. the pressure altitude is mathematically given as
PA=6500ft
What is the pressure altitude?Generally, the equation for the Pressure altitude is mathematically given as
PA = ( 29.92 - AltSet ) * 1000 + FieldElev.
Therefore
PA= (29,92 - 30.42) * 1000 + 6,500
PA=6000ft
In conclusion, pressure altitude
PA=6500ft
Read more about Pressure
https://brainly.com/question/25688500
what happens when you put foil in the microwave?
Answer:
The foil makes the microwave spark it can smoke up and catch fie.
Explanation:
-The aluminum foil's sharp edges are what causes the fire, smoke, and sarks.
- Hope This Helps!
-Justin:)
Answer:
itll spark and catch fire
Explanation:
If two forces act on an object, what is the relationship between the two forces? (pls explain)
A. The larger force causes the same acceleration as the smaller.
B. The larger force causes more acceleration than the smaller.
C. The larger force causes less acceleration than the smaller.
D. The smaller force and the larger force are balanced and therefore causes no acceleration.
Answer:
B. The larger force causes more acceleration than the smaller.
Explanation:
For example, let me use a child and a grown up. The child represents the smaller force while the grown up represents the larger force. If they are pushing the same object of different sides, obviously the side with the grown up will push and move to the side of the child because it is stronger.
What is the effect of increase in heat on:
1. Plastic
2. Iron
Explanation:
1.Plastic
Thermal Degradation – Plastic materials subjected to prolonged exposure to high temperatures will lose strength and toughness, becoming more prone to cracking, chipping, and breaking, at a rate in proportion to the temperature and time of exposure.
2.Iron
At room temperature, the iron atoms are in an unusual loosely packed open arrangement; as iron is heated past 912 degrees Celsius, the atoms become more closely packed before loosening again at 1,394 degrees Celsius and ultimately melting at 1,538 degrees Celsius
A car of mass 1500kg is brought to rest from a velocity of 25m/s by a constant force of 3,000N. Determine the change in momentum produced by the force and the time it takes for the car to come to rest.
Answer:
change in momentum = 37,500kg.m/s in the opposite direction
time it takes = 12.5s
Explanation:
u=25m/s
v=0m/s
F=ma
-3000=(1500)(a)
-3000÷1500=a
a= -2m/s^2
Change in momentum=mv-mu
(1500)(0)-(1500)(25)
= -37,500kg.m/s
relax the( - ) represents direction
v=u-at
0=25-2t
2t=25
t= 12.5s
A block initially at rest on a horizontal, frictionless surface is accelerated by a constant horizontal force of 5. 0 newtons. If 15 joules of work is done on the block by this force while accelerating it, the kinetic energy of the block increases by.
By the work-energy theorem, the block's kinetic energy is increased by 15 J. The only force performing work on the block is the constant 5.0-N push.
FOR STUDY ISLAND: Objects that stop the flow of electricity are good insulators. Which of the following materials would be the best insulator for an electrical wire?
A.
aluminum pipes
B.
copper wire
C.
plastic tubing
D.
water
Answer: It would be; A/B
i need help with this question on circuits!!
Answer:
B
A
A
B
Explanation:
In the wiring of houses, a parallel circuit is used, otherwise, if the circuit of one of the parts is interrupted, the current will not enter the other circuits.
Helppppp
5) Experimental Design Cavendish's homemade apparatus gave him a calculated
value for the Gravitational Constant of 6.74E-11 Nm²/kg? The accepted value today
(with 200 years more advanced technology) is 6.67E-11 Nm²/kg? What sources of
error might Cavendish have had? How might scientists have improved this
experiment over the years.
Answer:
The apparatus would need to be extremely delicate because of the very small values being measured, the gravitational attraction of two massive objects.
(I) the torsion constant, measuring the deflection of massive objects would be very small and difficult to measure accurately
(II) since all surrounding objects are massive, it is difficult to remove the effect of such objects from forces being measured
(III) to consider a massive object as having all of its mass at its center, the massive object would need to be uniform throughout - any nonuniformity of the object would affect the calculations
(IV) all physical measurements would need to be made with utmost accuracy because of the relatively small distances involved with regard to the extremely small force being measured
(V) today laser measurements would assist in measuring small deflections accurately
A proton wit a kinetic energy of 9. 3 x 10^-15 j moves perpendicular to a magnetic field of 0. 87 t. What is the radius of its circular path?
The radius of the given circular path moved by the proton which is perpendicular to a magnetic field of 0.87 T determined as 4 cm.
Magnetic force of the protonThe magnitude of the magnetic force on the proton is determined using the following formula;
F = qvBsin(θ)
Centripetal force on the protonThe centripetal force of the circular path is given as;
F = mv²/r
Solve the two equations together,
[tex]\frac{mv^2}{r} = qvBsin(90)\\\\r = \frac{mv}{qB}[/tex]
Where;
v is the speed of the protonSpeed of the protonThe speed of the proton is determined from its kinetic energy;
[tex]K.E = \frac{1}{2}mv^2\\\\ v= \sqrt{\frac{2K.E}{m} } \\\\v = \sqrt{\frac{2 \times 9.3 \times 10^{-15}}{1.67 \times 10^{-27}} } \\\\v = 3.33\times 10^6 \ m/s[/tex]
Radius of the circular pathThe radius of the circular path is calculated as follows;
[tex]r = \frac{(1.67 \times 10^{-27}) \times (3.33 \times 10^6)}{(1.6\times 10^{-19}) \times (0.87)} \\\\r = 0.04\ m\\\\r = 4 \ cm[/tex]
Learn more about magnetic force here: https://brainly.com/question/13277365
What happens to the water vapor in the air when the air temperature cools?
Answer:
it becomes a liquid. it becomes water