You are studying circular motion by placing pennies on a turntable and then turning it on so that it will spin. You keep increasing the speed until one of the pennies slips off. You repeat this procedure and observe that the penny close to the outer edge always slip off first. What is the best inference?
1.The penny near the edge has a greater tangential velocity than the one in the center, so it experiences more air resistance. It’s the effect of the air “blowing” it off.
2.The centripetal force required to keep the pennies in place increases with the distance from the center. Eventually, as the turntable spins faster, the friction force between the turntable and the penny near the edge is not enough to supply the required centripetal force.
3.The centrifugal force acting on the pennies is stronger on the one near the edge than the one near the center.
Answers
Answer:
2.The centripetal force required to keep the pennies in place increases with the distance from the center. Eventually, as the turntable spins faster, the friction force between the turntable and the penny near the edge is not enough to supply the required centripetal force.
Explanation:
centripetal force = m ω² R
here m is mass , ω is angular velocity and R is distance of penny from centre
So this force depends upon R
penny on the outer edge will require greater centripetal force to move in circular path .
The centripetal force will be provided by frictional force of table which is same for both the coin . Hence the penny on the outer edge will slip off first the moment , frictional force reach its maximum value for it . But it will be sufficient to keep in balance the penny nearer to the centre .
Related Questions
A region around the nucleus of an atom where electrons are likely to be found
Answers
Answer:
The region where an electron is most likely to be is called an orbital. Each orbital can have at most two electrons. Some orbitals, called S orbitals, are shaped like spheres, with the nucleus in the center.
Explanation:Hope this helps :)
By definition, a region around the nucleus of an atom where electrons are likely to be found is called an orbital.
First of all, an atom is the smallest constituent unit of ordinary matter that has the properties of a chemical element.
All atoms are made up of subatomic particles: protons and neutrons, which are part of their nucleus, and electrons, which revolve around them. Protons are positively charged, neutrons are neutrally charged, and electrons are negatively charged.
In other words, every atom consists of a nucleus in which neutrons and protons meet and energy levels where electrons are located.
This is, the atomic nucleus is the central part of the atom that is made up of protons and neutrons, while the orbitals or peripheral region is an area where electrons are found.
In summary, a region around the nucleus of an atom where electrons are likely to be found is called an orbital.
Learn more:
https://brainly.com/question/10866484?referrer=searchResultshttps://brainly.com/question/1275002?referrer=searchResultsbrainly.com/question/1814899?referrer=searchResults brainly.com/question/2449569?referrer=searchResultsHollywood and video games often depict the bad guys being "blown away" when they’re shot by a bullet (i.e. once hit, their feet leave the ground and they fly backwards). Assuming that even if a handgun cartridge did generate enough momentum for the bullet to do this, why is it still nonsense on-screen?
Answers
Answer:
Taking a look at Newton's third law of motion which states "for every force exerted, their is an opposite force equal in magnitude and opposite in direction on the first force".
Similarly if a bullet had enough forces behind it to hurl someone through the air when they were hit, a similar force would act on the person holding the gun that fired the bullet.
What we load into the gun is called a 'cartridge' Each piece is composed of four basic substance the casing, the bullet, the primer, and the powder.
The primer explodes lighting the powder which causes a buildup of pressure behind the bullet. This powder can be used in rifle cartages because the bullet chamber is designed to withstand greater pressures.
It is difficult in practice to measure the forces within a gun bagel, but the one easily measured parameter is the velocity with which the bullet exits muzzle velocity, therefore assuming that even if a handgun cartridge which generate enough momentum for the bullet to do this, it is still nonsense on screen in Hollywood and video.
A student studies the effect of an object's speed on its amount of kinetic energy. This graph summarizes the data from the study Kinetic energy Speed Which statement best describes what the graph shows?
A. As speed increases, kinetic energy increases exponentially
B. As speed increases, kinetic energy stays the same
C. As speed decreases, kinetic energy doubles each time.
D. As kinetic energy increases, speed decreases exponentially
Answers
The answer is A I Hope this answer helps you (i got the question right)
Answer:
A. As speed increases, kinetic energy increases exponentially.
Explanation:
The amount of kinetic energy an object has depends on the speed. Kinetic energy is also known as "motion energy." This being said, if speed is increasing, decreasing, or staying constant, the kinetic energy of the object will too.
Find the work done by a 75.0 kg person in climbing a 2.50 m flight of stairs at a constant speed.
Answers
Answer:
1,839.375 Joules
Explanation:
Work is said to be done is the force applied to an object cause the object to move through a distance.
Workdone = Force * Distance
Workdone = mass * acceleration due to gravity * distance
Given
Mass = 75.0kg
acceleration due to gravity = 9.81m/s²
distance = 2.50m
Substitute the given parameters into the formula:
Workdone = 75.0*9.81*2.50
Workdone = 1,839.375Joules
Hence the workdone is 1,839.375 Joules
Given that water at standard pressure freezes at 0∘C, which corresponds to 32∘F, and that it boils at 100∘C, which corresponds to 212∘F, calculate the temperature difference ΔT in degrees Fahrenheit that corresponds to a temperature difference of 1 K on the Kelvin scale. Give your answer to two significant figures.
Answers
Answer:
In two significant figure 360K
Explanation:
The temperature difference (ΔT) can be calculated as the boiling temperature minus the freezing temperature in Fahrenheit.
Hence,
ΔT = 212 - 32
ΔT = 180°F
To convert to °F to kelvin, we use the formula below
= (°F - 32) × 5/9 + 273.15
= (180°F - 32) × 5/9 + 273.15
= 355.37K ⇔ 360K
I need help with this answer
Answers
6) The magnitude of the force the Sun exerts on Uranus is 1.41 x 1021 newtons. Explain how it is possible for the Sun to exert agreater force on Uranus than Neptune exerts on Uranus.
Answers
Answer and Explanation:
TL: DR The Sun is much more massive than Neptune — more than enough to make up for the somewhat smaller distance between the two planets at the closest approach.
[The surprise in this answer (to me, a non-astronomer), is that the gap between the orbits of Neptune and Uranus is large — half the distance from Uranus to the Sun.]
The ratio of gravitational attraction of the Sun on Uranus versus Neptune on Uranus is directly proportional to the ratio of the Sun’s mass to Neptune’s and inversely proportional to the ratio of the square of the distances (let’s use the closest approach of the two planets to one another to calculate a maximum attraction).
Numbers:
Sun’s mass: 2 x 10^30 kg
Neptune’s mass: 1 x 10^26 kg
Distance of Sun to Uranus: 3 x 10^9 km
Closest approach of Uranus and Neptune: 1.5 x 10^9 km
Without doing any arithmetic, we see that even at their closest approach, Uranus and Neptune are separated by about one-half of the Uranus to Sun distance. Squaring that ratio, we see that if the Sun and Neptune had the same mass, the attraction between the Sun and Uranus would only be about 1/4 of that between the Sun and Neptune; however, the Sun has 20000 times the mass of Neptune, so the attraction between Uranus and the Sun is about 5000 times stronger than the maximum attraction between Uranus and Neptune.
The explanation of the possibility of why sun exerts a greater force on Uranus than Neptune exerts on Uranus is; because the force was calculated to be greater.
The formula for calculating the Force of Gravity between two masses is:
F = G*m₁*m₂/r²
Where;
F = force of gravity
G = gravitational constant = 6.674 × 10⁻¹¹ N•m²/kg²
m₁ = mass of the larger object
m₂ = mass of the smaller object
r = the distance between the centers of the two masses
Now, from online values, we have the following;
mass of Neptune; m₁ = 102.413 × 10²⁴ kg
mass of Uranus; m₂ = 86.813 × 10²⁴ kg
average distance between the centers of Neptune and Uranus; r = 1.62745 × 10¹² m
Thus, force exerted by Neptune on Uranus is;
F = (6.674 × 10⁻¹¹ × 102.413 × 10²⁴ × 86.813 × 10²⁴)/(1.62745 × 10¹²)²
F = 2.240 × 10¹⁷ N
We are told that the force the Sun exerts on Uranus is 1.41 the force the Sun exerts on Uranus is 1.41 × 10²¹ N.
That is greater than the force Neptune exerts on Uranus.
Read more about Force of Gravity at; https://brainly.com/question/7281908
A cart with an unknown mass is at rest on one side of a track. A student must find the mass of the cart by using Newton’s second law. The student attaches a force probe to the cart and pulls it while keeping the force constant. A motion detector rests on the opposite end of the track to record the acceleration of the cart as it is pulled. The student uses the measured force and acceleration values and determines that the cart’s mass is 0.4kg . When placed on a balance, the cart’s mass is found to be 0.5kg . Which of the following could explain the difference in mass?
Answer choices:
A) The track was not level and was tilted slightly downward.
B) The student did not pull the cart with a force parallel to the track.
C) The wheels contain bearings that were rough and caused a significant amount of friction.
D) The motion sensor setting was incorrect. The student set it up so that motion away from the sensor would be the negative direction.
Answers
Answer: The correct answer is A) The track was not level and was tilted slightly downward.
Explanation: This is because of the two values: 0.4 kg and 0.5 kg. I won't go into much detail but due to this difference of mass, we know that the track was not level.
"The track was not level and was tilted slightly downward" could explain the difference in the mass.
Mostly because the university student or learners calculates a mass of just over the spring quantity, the vehicle speed seems to have been higher than there would have had to be.Option B, as well as Option C, are wrong because the acceleration would've been smaller in each of these 2 circumstances, so that computed mass would've been larger.
Thus Option A is appropriate.
Learn more:
https://brainly.com/question/11839345
A 126 N force is applied at an angle of 25.00 to a 8.50 kg block pressed against a rough vertical wall and the block slides down the wall at constant velocity. Calculate the coefficient of kinetic friction between the block and the wall.
Answers
Answer:
μk = 0.58
Explanation:
If the block is sliding down at constant speed, this means that no net force is acting upon it in the vertical direction.As the block is pressed on the wall, this means that it doesnt accelerate in the horizontal direction either, so no net force acts upon it in this direction also.In this direction, we have only two forces acting, equal and opposite each other, one is the normal force (exerted by the wall) and the other is the horizontal component of the applied force.If the applied force forms an angle of 25º with the wall (which is vertical), this means that we can get its projection along the horizontal direction, using simple trigonometry , as follows:[tex]F_{apph} = F_{app} * sin\theta = 126 N * sin 25 = 53.3 N[/tex]
⇒ [tex]F_{n} = - F_{apph} = -53.3 N[/tex]
In the vertical direction, we have three forces acting on the block: the weight pointing downward, the kinetic friction force (as we know that the block is sliding), and the vertical component of the applied force, in the same direction as the friction one.As we have already said, the sum of these forces must be 0.[tex]F_{g} + F_{appv} + F_{ff} = 0 (1)[/tex] where Fg is the weight of the block, Fappv is the vertical component of the applied force, and Fff is the kinetic friction force.Replacing these forces by their mathematical expressions, we have:[tex]F_{g} = m_{b} * g = 8.5 Kg * (-9.8 m/s2) = -83.3 N[/tex]
[tex]F_{appv} = F_{app}* cos\theta = 126 N * cos 25 = 114.2 N[/tex]
[tex]F_{ff} = \mu_{k}* F_{n} =\mu_{k} * (-53.3 N)[/tex]
Replacing in (1), and solving for μk, we finally get:μk = 0.58
An 80-kg bungee jumper jumps off a bridge. Rubber bungee cords act as a large spring attaching the jumper to the bridge. A bear standing in the river below catches the jumper. If the spring constant of the bungees is 20 N/m and they stretch 50 m. How much force must the bear apply to keep the jumper from moving?
Answers
Answer:
The force is [tex]F_b = 216 \ N [/tex]
Explanation:
From the question we are told that
The mass of the bungee jumper is m = 80 kg
The spring constant is [tex]k = 20 \ N/ m[/tex]
The extension of the rubber bungee cords is x = 50 m
Generally the weight of the jumper is
[tex]W = m * g[/tex]
=> [tex]W = 80 * 9.8 [/tex]
=> tex]W = 784 \ N [/tex]
Generally the returning force of the rubber bungee cords is mathematically represented as
[tex]F = k * x[/tex]
=> [tex]F = 20 * 50 [/tex]
=> [tex]F = 1000 \ N [/tex]
The force to be applied by the bear is
[tex]F_b = F - W[/tex]
=> [tex]F_b = 100 - 784[/tex]
=> [tex]F_b = 216 \ N [/tex]
How many strings of length 10 over the alphabet (a, b, c, d] have at least one b somewhere in the string?
a) 310
b) 410 - 310
c) 10.4
d) 10.39
Answers
Complete Question
The complete question is shown on the first uploaded image
Answer:
The correct option is B
Explanation:
The number of alphabet is n= 4 (a , b , c , d )
Generally the total number of string of length 10 over the 4 alphabets is
[tex]N = 4^{10}[/tex]
Gnerally the number of string of length 10 that does not include b is
[tex]T = 3^{10}[/tex]
Generally the number of strings of length 10 over the 4 alphabets that have at least one alphabet b somewhere in the string is
[tex]G = N - T[/tex]
=> [tex]G = 4^{10} - 3^{10}[/tex]
A single living thing.
Answers
Answer:
What do you mean ma´am/sir?
Explanation:
How do compounds differ from mixtures such as lemonade
Answers
Answer:
A mixture is a combination of two or more substances in any proportion. This is different from a compound, which consists of substances in fixed proportions. ... The lemonade pictured above is a mixture because it doesn't have fixed proportions of ingredients.
Explanation:
Is it true or false that the displacement always equals the product of the average velocity and the time interval?
Answers
Answer:
True.
Explanation:
Applying the definition of average velocity, we know that we can always write the following expression:[tex]v_{avg} = \frac{\Delta x}{\Delta t}[/tex] (1)
By definition, Δx is just the displacement, and Δt is the time interval.So, just rearranging terms in (1), we get:[tex]\Delta x} = v_{avg}* {\Delta t}[/tex]
Plz help me fast WITH EXTRA POINTS AFTER SUBMITTING
Answers
Answer:
4 bobux
Explanation:
one bobux
two bobux
three bobux
four bobux
Metals that have shine and luster?
Answers
Answer:
luster
Explanation:
A 50 kg bicyclist starts his ride down the road with an acceleration of 1m/s2 in air with a density of 1.2 kg/m3. If his velocity at a given moment is 2m/s, how much force is he exerting? Assume the area of his body is 0.5m^2.
a. The bicyclist is exerting 1.1 N of force.
b. The bicyclist is exerting 49 N of force.
c. The bicyclist is exerting 50 N of force.
d. The bicyclist is exerting 51 N of force.
Answers
Answer:
b. The bicyclist is exerting 49 N of force
Explanation:
Given;
mass of bicyclist start, m = 50 kg
acceleration, a = 1 m/s²
density of air, ρ = 1.2 kg/m³
velocity, v = 2 m/s
Area of the bicyclist body, A = 0.5 m²
The drag force on the bicyclist is given by ;
Fd = 0.5CρAv²
where;
C is drag coefficient = 0.9 for bicycle
Fd = 0.5 x 0.9 x 1.2 x 0.5 x 2²
Fd = 1.1 N
The force of the bicyclist is given by;
F = ma
F = 50 x 1
F = 50 N
The effective force exerted by the bicyclist is given by;
Fe = F - Fd = 50 N - 1.1 N
Fe = 49 N
Therefore, the force exerted by the bicyclist is 49 N
The word acid comes from the Latin word
Answers
The word acid comes from the Latin word acere, which means sour
Hope this helps!
Which is a belief held by sociologists who work from a social-conflict
perspective?
O A. The best approach for a study is from a micro-level orientation.
O B. Personal background has little impact on how individuals react
with one another.
C. Some social patterns are helpful, while others are harmful.
D. Data are irrelevant to the study of sociology.
SUBMIT
Answers
Answer:
C. Some social patterns are helpful, while others are harmful.
Explanation:
Hope this was helpful, Have an amazing,spooky Halloween!!
A yo-yo is made of two solid cylindrical disks, each of mass 0.055 kg and diameter 0.070 m , joined by a (concentric) thin solid cylindrical hub of mass 0.0055 kg and diameter 0.011 m . Part A Use conservation of energy to calculate the linear speed of the yo-yo when it reaches the end of its 1.1 m long string, if it is released from rest. Express your answer using three significant figures and include the appropriate units.
Answers
Answer: IM 95%sure that the answer is B jus took the test got the answer right
Explanation:
Answer:
sorry I forgot I wish I could help
Velocity which stone gains when falling from height of 80 m is approximately equal to *
A. 0
B. 1 m/s
C. 8 m/s
D. 40 m/s
E. 300 m/s
Answers
Answer:
40
Explanation:
How much work is required to move it at constant speed 5.0 m along the floor against a friction force of 290 N?
Answers
Answer:
The answer is 1450 JExplanation:
The work done by an object can be found by using the formula
workdone = force × distanceFrom the question
force = 290 N
distance = 5 m
We have
workdone = 290 × 5
We have the final answer as
1450 JHope this helps you
what is the meaning of relative as a noun?
Answers
Answer:
noun. a person who is connected with another or others by blood or marriage. something having, or standing in, some relation or connection to something else. something dependent upon external conditions for its specific nature, size, etc. (opposed to absolute).
as a result, the net electric force experienced by each negatively charged particle is reduced to F/2. The value of q is
Answers
Answer:
The value of q is [tex]\dfrac{Q}{8}[/tex]
Explanation:
Given that,
Each charge = -Q
Distance between charges = L
Reduced force = [tex]\dfrac{F}{2}[/tex]
Suppose, Two particles each with a charge -Q are fixed a distance L apart as shown above. Each particle experiences a net electric force F. A particle with a charge +q is now fixed midway between the original two particles.
We know that,
The force on each end is
[tex]F=\dfrac{kQ^2}{L^2}[/tex]...(I)
If the charge q is placed at mid point then
The force on each end charge is
[tex]\dfrac{F}{2}=F+F'[/tex]....(II)
We need to calculate the value of q
Using equation (II)
[tex]\dfrac{F}{2}=F+F'[/tex]
Put the value of F into the formula
[tex]\dfrac{\dfrac{kQ^2}{L^2}}{2}=k\dfrac{Q^2}{L^2}+k\dfrac{q\times(-Q)}{(\dfrac{L}{2})^2}[/tex]
[tex]\dfrac{kq(-Q)}{(\dfrac{L}{2})^2}=-\dfrac{kQ^2}{2L^2}[/tex]
[tex]\dfrac{q}{\dfrac{1}{4}}=\dfrac{Q}{2}[/tex]
[tex]q=\dfrac{Q}{8}[/tex]
Hence, The value of q is [tex]\dfrac{Q}{8}[/tex]
See Conceptual Example 6 to review the concepts involved in this problem. A 12.0-kg monkey is hanging by one arm from a branch and swinging on a vertical circle. As an approximation, assume a radial distance of 86.4 cm is between the branch and the point where the monkey's mass is located. As the monkey swings through the lowest point on the circle, it has a speed of 1.33 m/s. Find (a) the magnitude of the centripetal force acting on the monkey and (b) the magnitude of the tension in the monkey's arm.
Answers
Answer:
(a) 24.56 N
(b) 142.28 N
Explanation:
(a)
The designation assigned to something like the net force pointed toward the middle including its circular route seems to be the centripetal force. The net stress only at lowest point constitutes of the strain throughout the arm projecting upward towards the middle as well as the weight pointed downwards either backwards from the center.
The centripetal function is generated from either scenario by Equation:
⇒ [tex]Fc = \frac{mv^2}{r}[/tex]
On putting the values, we get
⇒ [tex]=\frac{12\times 1.33^2}{0.864}[/tex]
⇒ [tex]=24.56 \ N[/tex]
(b)
Use T to denote whatever arm stress we can get at the bottom including its circle:
⇒ [tex]Fc = T - mg =\frac{ mv^2}{r}[/tex]
⇒ [tex]T = mg + Fc[/tex]
⇒ [tex]=12\times 9.81+24.56[/tex]
⇒ [tex]=142.28 \ N[/tex]
An ideal gas increases in temperature from 22°C to 42°C by two different processes. In one process, the temperature increases at constant volume, and in the other process the temperature increases at constant pressure. Which process requires more heat or are the required amount of heat same in both?
Answers
Answer:
a- More heat is required for the constant-pressure process than for the constant-volume
Explanation:
we have to solve using the thermodynamic first law. this is the heat applied to the system
dQ = dU + dW
definition of terms:
dU = change in internal energy
dW = work done
we have it that
change in internal energy dU is directly proportional to work done dW
but when we are in constant volume process, work done of the gas is zero
therefore
dQ of constant pressure is > than that of constant volume
so constant pressure process requires more heat
The process that requires more heat is the constant-pressure process than the constant-volume process.
According to the first law of thermodynamics, the heat that's applied to the system will be the addition of the change in internal energy and the work done.
In a constant-volume process, the work done on the gas is equal to zero. More heat will be required for the constant-pressure process than for the constant-volume process.
Also, it should be noted that the change in the thermal energy of the gas will be the same for the constant-pressure process and the constant-volume process.
Read related link on:
https://brainly.com/question/16951562
Time it takes stone to fall from the height of 80 m is approximately equal to *
A. 1 s
B. 2 s
C. 4 s
D. 8 s
Answers
Answer:
D
Explanation:
Answer:
c.4s
Explanation:
my heart strike him to dead.what figure of speech is that?
Answers
Answer:
Hyperbole
Explanation:
this is an extreme exaggeration or overstatement/ magnification
Alejandro made 6.4 liters of punch using half apple juice and half orange juice. How many milliliters of apple juice are in the punch?
Answers
Answer:
3.2
Explanation:
I hope that this helps! Have a good day!!
Compare the amount of thermal energy required to MELT a solid with the amount of thermal energy released when the same liquid becomes a solid.