Answer:
B
Explanation:
I'm learning it in science.
Answer:
its not b i just took the test and b was wrong
Explanation:
A circular wire loop lies inside a region of space containing a magnetic field. The direction of the magnetic field is out of the screen and parallel to the central axis of the loop. The magnitude of the magnetic field increases as a function of time. A circular loop oriented parallel to the plane of the screen lies inside a region containing magnetic field B. The field is directed out of the screen and is increasing. What is the direction of the induced current in the loop
Answer:
clockwise
Explanation:
According to the law given by Lenz, known as the Lenz law, it is said that a current induced in the circuit which is due to the change in the magnetic field and is so directed so as to oppose the change in the flux and to apply a force in the opposite direction if the force.
Here, as the magnetic field is directed out of the screen, the current flows in the direction which is clockwise in the loop and it opposes the increasing magnetic field.
The clockwise induced current will produce magnetic field in to the screen.
This 200-kg horse ran the track at a speed of 5 m/s. What was the average kinetic energy?
Answer:
2500 JExplanation:
The average kinetic energy can be found by using the formula
[tex]k = \frac{1}{2} m {v}^{2} \\ [/tex]
m is the mass
v is the velocity
From the question we have
[tex]k = \frac{1}{2} \times 200 \times {5}^{2} \\ = 100 \times 25[/tex]
We have the final answer is
2500 JHope this helps you
What best describes the speed of light waves in solids, liquids, and gases?
The speed is fastest in solids.
The speed is fastest in liquids.
The speed is fastest in gases.
The speed is the same in all matter.
Answer: It’s fastest in gases. Letter C !
Explanation:
Answer:
its c
Explanation:
You're driving a bumper car at a circus at
18 m/sec, and you hit another car that's at
rest. If you end up going at 6.0 m/sec, what
is the final speed of the other car, given
that both cars have 100.0 kg mass, you
have 80.0 kg mass, and the other person
has a mass of 70.0 kg?
Answer:
PLEASE MARK AS BRAINLIEST!!
Explanation:
ANSWER IS IN THE IMG BELOW
How fast, in meters per second, does an observer need to approach a stationary sound source in order to observe a 7.1 % increase in the emitted frequency?
Answer:
v0 = 24.42 m/s (Approx)
Explanation:
Given:
Increase in frequency = 7.1% =
Computation:
Assume n = 100%
n1 = [(v+v0)/(v+v1)]n
[100 + 7.1] = [(344+v0)/(344+0)]100
107.1 = [(344+v0)/(344)]100
v0 = 24.42 m/s (Approx)
HELP ASAP!! i’ll mark you the brainliest!!
Answer:
yes
Explanation:
1. express the following in proper SI form using the appropriate prefixes. a. 52500000 m b. 1000 g c. 2435200000
Answer:
a
[tex]L = 5.25*10^{7} \ m[/tex]
b
[tex]m = 1 \ kg[/tex]
c
[tex]t = 1.46112000000 *10^{11} \ s[/tex]
Explanation:
From the question we are told that
Length is L = 52500000 m
Mass is
Time is 2435200000 minutes
Generally the proper SI for length is meters ,
Now converting the given length to proper SI form using the appropriate prefixes we have that
[tex]L = 5.25*10^{7} \ m[/tex]
Generally the proper SI for mass is kilograms
converting grams to kilograms , we have
[tex]m =\frac{1000}{1000 }[/tex]
=> [tex]m = 1 \ kg[/tex]
Generally the proper SI for time is seconds
converting minutes to seconds , we have
[tex]t = 24352000000* 60[/tex]
=> [tex]t = 146112000000 \ s[/tex]
Now converting to the proper SI form using the appropriate prefixes
[tex]t = 1.46112000000 *10^{11} \ s[/tex]
Use the image below to answer the question.
What does the arrow 'B' represent?
Question 7 options:
wavelength
refraction
frequency
compression
A ray moving in water at 55.5 deg
enters plastic, where it bends to
48.7 deg. What is the index of
refraction for the plastic?
( water n = 1.33, Air n = 1.00 )
Answer:
Refractive index of the plastic = 1.46
Explanation:
By Snell's law,
[tex]\frac{\text{sin}\theta _{2} }{\text{sin}\theta _{1}}=\frac{n_1}{n_2}[/tex]
Here, [tex]\theta _1[/tex] = Angle of incidence in medium 1 (Plastic)
[tex]\theta_2[/tex] = Angle of refraction in medium 2 (Water)
[tex]n_1[/tex] = Refractive index of medium 1 (Plastic)
[tex]n_2[/tex] = Refractive index of medium 2 (Water)
By substituting values in the formula,
[tex]\frac{\text{sin}(48.7)}{\text{sin}(55.5)}=\frac{1.33}{n_2}[/tex]
[tex]n_2=\frac{1.33\times \text{sin}(55.5)}{\text{sin}(48.7)}[/tex]
= 1.46
Therefore, refractive index of the plastic = 1.46
Need help ASAP plsss
Write 5-6 sentences about
:how do parachutes work ??
A ripcord system pulls a closing pin, which releases a spring-loaded pilot chute, and opens the container; from which the parachute comes out.
If a skydiver is unable to open her/his parachute, an automatic activation device will automatically open the parachute.
A parachute works by forcing air into the front of it and creating a structured 'wing' under which the canopy pilot can fly. Parachutes are controlled by pulling down on steering lines which change the shape of the wing, cause it to turn, or to increase or decrease its rate of descent.
A little girl pushes a 5.0 kg toy baby stroller at constant speed 7.0 m across the floor. She pushes on the handle with a force of 40 N at an angle of 30o with the horizontal. All parts are 4 points each.
Complete Question
1 a A little girl pushes a 5.0 kg toy baby stroller at constant speed 7.0 m across the floor. She pushes on the handle with a force of 40 N at an angle of 30o with the horizontal. How much work is done by the girl on the wagon?
1b A farmhand pushes 20 ㎏ bale of hay 4m across the floor of the barn if she exerts a horizontal force of 60 N on the hay, how much work is done? (5 pts)
All parts are 4 points each
Answer:
1a
[tex]W = 242.5 \ J[/tex]
1b
[tex]W = 240 \ J[/tex]
Explanation:
Considering question a
From the question we are told that
The mass of the toy baby stroller is [tex]m = 5.0 \ kg[/tex]
The distance covered is [tex]d = 7.0\ m[/tex]
The force the girl applies on the handle is [tex]F = 40 \ N[/tex]
The angle at which this force is applied is [tex]\theta = 30^o[/tex]
Generally the workdone is mathematically represented as
[tex]W = F_x * d[/tex]
Here [tex]F_x[/tex] is the force along the horizontal axis , this is mathematically represented as
[tex]F_x = F cos (\theta )[/tex]
=> [tex]F_x = 40 * cos(30 )[/tex]
=> [tex]F_x = 34.64 \ N[/tex]
So
[tex]W = 34.64 * 7[/tex]
=> [tex]W = 242.5 \ J[/tex]
Considering question b
From the question we are told that
The mass of the toy baby stroller is [tex]m = 20 \ kg[/tex]
The distance covered is [tex]d = 4 \ m[/tex]
The force the girl applies on the handle is [tex]F = 60 \ N[/tex]
Generally the workdone is mathematically represented as
[tex]W = F * d[/tex]
=> [tex]W = 60 * 4[/tex]
=> [tex]W = 240 \ J[/tex]
Which has a greater force: a semi-truck at rest or a moving bicycle?
Although the semi truck certainly has a larger mass, it is not in motion and therefore does not have any momentum. The bicycle however has both mass and velocity and therefore has the larger momentum of the pair.
A thyristor (SCR) is a
Answer:
A thyristor (/θaɪˈrɪstər/) is a solid-state semiconductor device with four layers of alternating P- and N-type materials. It acts exclusively as a bistable switch, conducting when the gate receives a current trigger, and continuing to conduct until the voltage across the device is reversed biased, or until the voltage is removed (by some other means).
Explanation:
Correct me if im wrong
a 2 kg block is attached to a horizontal ideal spring with a spring constant 200N/m. when the
Explain how polarization of a cell increases the cell's internal resistance.
(2
2.
Answer:
Explanation: The chemical action that occurs in the cell while the current is flowing causes hydrogen bubbles to form on the surface of the anode. This action is called POLARIZATION. Some hydrogen bubbles rise to the surface of the electrolyte and escape into the air, some remain on the surface of the anode. If enough bubbles remain around the anode, the bubbles form a barrier that increases internal resistance. When the internal resistance of the cell increases, the output current is decreased and the voltage of the cell also decreases.
A cell that is heavily polarized has no useful output. There are several methods to prevent polarization or to depolarize the cell.
One method uses a vent on the cell to permit the hydrogen to escape into the air. A disadvantage of this method is that hydrogen is not available to reform into the electrolyte during recharging. This problem is solved by adding water to the electrolyte, such as in an automobile battery. A second method is to use material that is rich in oxygen, such as manganese dioxide, which supplies free oxygen to combine with the hydrogen and form water.
A third method is to use a material that will absorb the hydrogen, such as calcium. The calcium releases hydrogen during the charging process. All three methods remove enough hydrogen so that the cell is practically free from polarization.
LOCAL ACTION
When the external circuit is removed, the current ceases to flow, and, theoretically, all chemical action within the cell stops. However, commercial zinc contains many impurities, such as iron, carbon, lead, and arsenic. These impurities form many small electrical cells within the zinc electrode in which current flows between the zinc and its impurities. Thus, the chemical action continues even though the cell itself is not connected to a load.
Local action may be prevented by using pure zinc (which is not practical), by coating the zinc with mercury, or by adding a small percentage of mercury to the zinc during the manufacturing process. The treatment of the zinc with mercury is called amalgamating (mixing) the zinc. Since mercury is many times heavier than an equal volume of water, small particles of impurities weighing less than mercury will float to the surface of the mercury. The removal of these impurities from the zinc prevents local action. The mercury is not readily acted upon by the acid. When the cell is delivering current to a load, the mercury continues to act on the impurities in the zinc. This causes the impurities to leave the surface of the zinc electrode and float to the surface of the mercury. This process greatly increases the storage life of the cell.
According to The Flash, The heroes top speed is Mach 3.3, or 2,500 miles per hour. How
long would it take for him to run around the planet? (circumference of the earth is
roughly 25,000 miles) *
Answer:
nearly 2 days or less hes fast but not that fast
Explanation:
but maybe he can run it in five minutes
What kind of electricity does turning wheel generates? Please help!
Answer: Kinetic Energy to Electrical.
Explanation: The magnet is rotated as a result of the spinning wheels, and this results in a powerful stream of electrons, therefore converting kinetic to electrical.
what are the importance of informal education?
Answer:
Informal education is important because it can help individual to learn how to react and control situations.
It help individual to improve on its existing knowledge, new skills or ideas. This kind of education can happen any where and it can add values to the learner.
Explanation:
Informal education is a type of education that is learned from different life experiences, happenings outside a structured curriculum.
Informal education is important because it can help individual to learn how to react and control situations.
It help individual to improve on its existing knowledge, new skills or ideas. This kind of education can happen any where and it can add values to the learner.
You have to move your 100 N couch before a delivery company drops off your new one. Unfortunately your roommate is passed out on it. The coefficient of friction between the couch and floor is .43. It takes 250 N of force to get the couch moving. a) How much does your roommate weigh in Newton’s? b) After you get the couch moving it only takes 200 N to keep it moving at a constant speed, what is the coefficient of kinetic friction?
Answer:
a) Weight of Roommate = 481.4 N
b) μk = 0.34
Explanation:
a)
The force required to move the couch must be equal to the force of friction:
F = frictional force
F = μW
W = F/μ
where,
W = Total Weight of Couch and Roommate
F = Force Required start to move couch = 250 N
μ = coefficient of static friction between couch and floor = 0.43
Therefore,
[tex]W = \frac{250 N}{0.43}\\\\W = 581.4 N[/tex]
So, the total weight is given as:
W = Weight of Couch + Weight of Roommate
Weight of Roommate = W - Weight of Couch
Weight of Roommate = 581.4 N - 100 N
Weight of Roommate = 481.4 N
b)
Now, the force required to keep the couch moving can be given as equal to the kinetic friction force:
F = kinetic friction
F = μk*W
μk = F/W
where,
μk = coefficient of kinetic friction = ?
F = Force required to keep the couch moving = 200 N
Therefore,
μk = 200 N/581.4 N
μk = 0.34
Multiply.
(2x + 4)(x - 4)
Answer:
(2x + 4)(x - 4)=2x^2-4x-16
Developing study routines is a way to organize
a. Yes
b. No
Answer:
a. yes
Explanation:
................
12 seconds after starting from rest a frewly falling cantaloupe has a speed of
Answer:
The cantaloupe has a speed of 117.6 m/s
Explanation:
Free Fall Motion
It occurs when an object falls under the sole influence of gravity. Any object that is being acted upon solely by the force of gravity is said to be in a state of free fall. Free-falling objects do not face air resistance.
If an object is dropped from rest in a free-falling motion, it falls with a constant acceleration called the acceleration of gravity, which value is [tex]g = 9.8 m/s^2[/tex].
The final velocity of a free-falling object after a time t is given by:
vf=g.t
The cantaloupe has been dropped from rest. We are required to find the speed after t=12 seconds.
Calculate the final speed:
vf=9.8 * 12 = 117.6 m/s
The cantaloupe has a speed of 117.6 m/s
. A pendulum of length l = 9.8 m hangs in equilibrium and is then given velocity
v
=0.2
m/s at its lowest point. What is the amplitude of the subsequent oscillation?
Answer:
the amplitude of the sequence oscillation=
ASO = length × velocity
= 9.8 × 0.2 = 19.6
ASO = 19.6
A piece of copper wire with thin insulation, 200 m long and 1.00 mm in diameter, is wound onto a plastic tube to form a long solenoid. This coil has a circular cross section and consists of tightly wound turns in one layer. If the current in the solenoid drops linearly from 1.60 A to zero in 0.120 seconds, an emf of 80.0 mV is induced in the coil. What is the length of the solenoid, measured along its axis
Answer:
N= 3
Explanation:
For this exercise we must use Faraday's law
E = - dФ / dt
Ф = B . A = B Acos θ
tje bold indicate vectors. As it indicates that the variation of the field is linear, we can approximate the derivatives
E = - A cos θ (B - B₀) / t
The angle enters the magnetic field and the normal to the area is zero
cos 0 = 1
A = π r²
In the length of the wire there are N turns each with a length L₀ = 2π r
L = N (2π r)
r = L / 2π N
we substitute
A = L² / (4π N²)
The magnetic field produced by a solenoid is
B = μ₀ N/L I
for which
B₀ = μ₀ N/L I
The final field is zero, because the current is zero
B = 0
We substitute
E = - (L² / 4π N²) (0 - μ₀ N/L I) / t
E = μ₀ L I / (4π N t)
N = μ₀ L I / (4π t E)
The electromotive force is E = 0.80 mV = 0.8 10⁻³ V
let's calculate
N = 4π 10⁻⁷ 200 1.60 / (4π 0.120 0.8 10⁻³)]
N = 320 10⁻⁷ / 9.6 10⁻⁶
N = 33.3 10⁻¹
N= 3
Some metals have a molecular structure that makes them good conductors. Explain how understanding this relationship can help engineers make more powerful batteries.
Answer:
Explained below.
Explanation:
Conductors can be defined as materials that permit electricity to flow through them easily.
Now, metals have a molecular structure that makes them good conductors because electrons in the atoms of these conductors tend to move freely from one atom to the other. So a majority of metals make good conductors because these metals tend to hold their electrons loosely. In short, it can help engineers make powerful batteries because then it means that they are capable of giving much more electrical energy since nowadays, advanced batteries make use of ion charges for the batteries.
A 300 g bird flying along at 6.0 m/s sees a 10 g insect heading straight toward it with a speed of 30 m/s. the bird opens its mouth wide and enjoys a nice lunch. What is the bird's speed immediately after swallowing?
Answer:
6.77m/s
Explanation:
Using the law of conservation of momentum
m1u1 + m2u2 = (m1+m2)v
m1 and m2 are the masses of the object
u1 and u2 are the velocities before collision
v is the final collision
Given
m1 = 300g = 0.3kg
u1 = 6.0m/s
m2 = 10g = 0.01kg
u2 = 30m/s
Required
The bird's speed immediately after swallowing v
Substitute the given values into the formula
m1u1 + m2u2 = (m1+m2)v
0.3(6) + 0.01(30) = (0.3+0.01)v
1.8+0.3 = 0.31v
2.1 = 0.31v
v = 2.1/0.31
v = 6.77m/s
Hence the bird's speed immediately after swallowing is 6.77m/s
what is the difference between alcoholic and Mercury thermometer based on their function?
A ball of mass 4kg moving with a velocity of 20m/s collides with another ball of mass 15kg moving with a velocity of 15m/s in the same direction. Calculate the velocity of the 5kg ball if the collision is perfectly inelastic.
Answer:
velocity = 16.05 m/s
Explanation:
inelastic collision formula:
m1u1 + m2u2 = (m1 + m2)v
m1 = 4kg
u1 = 20m/s
m2 = 15kg
u2 = 15m/s
find v ?
m1u1 + m2u2 = (m1 + m2)v
(4×20) + (15×15) = (4+15)v
80 + 225 = 19v
305 = 19v
19v = 305
v = 305/19
v = 16.05 m/s
identical spheres are dropped from a height of 100 m above the surfaces of Planet X and Planet Y. The speed of the spheres as a function of time is recorded for each planet in the graph
above. Which planet exerts the greater force of gravity on the sphere, and what evidence supports this conclusion?
A Planet X because its line has the greater area under it.
Planet X, because its line has the greater slope
Planet Y. because it falls for the smaller amount of time
Planet Y because the object's final speed is greater
Answer:
B. Planet X, because its line has the greater slope.
Explanation:
In a speed graph, acceleration is slope. A greater slope means a greater acceleration. According to Newton's 2nd law (F=mg), a greater acceleration means a greater force.
Planet X exerts the greater force of gravity on the sphere, because its line has the greater slope. Hence option B is correct.
What is Gravitational Force ?Gravitational force is force of attraction between two masses. Gravitational force(F) between two bodies is directly proportion to the product of masses(m₁,m₂) of two bodies and inversely proportional to square of distance(r) between them. mathematically it is written as,
F ∝ m₁.m₂
F ∝ 1/r²
F = G m₁,m₂÷r²
where G is gravitational constant, whose value is 6.6743 × 10⁻¹¹ m³ kg-1s⁻².
Force is expressed in Newton N in SI unit. its dimensions are [M¹L¹T⁻²].
This is analogous with coulomb's law which gives force between two charges.
if a planet has greater gravitational force(force of gravity), then body falls with greater speed as compare to other planet which is having less force of gravity. we can see in case of planet X there is greater speed as compare to plane Y in short time. Hence option B is correct.
To know more about Gravity :
https://brainly.com/question/31321801
#SPJ2.
mester Exam 1 11 of 35
A car has an oil drip. As the car moves, it drips oil at a regular rate, leaving a trail of spots on the road. Which diagram shows the spots
of car that is continuously slowing down?