Answer:
None of the above cause thats what i put
1. Looking at the case study provided under the Companion Material section, what is the main problem that is addressed in this case study? Maintenance workers painted over the pipes. Engineers lost all of their work because of the flood. The water pipes broke and flooded the space center. There was no paperwork for the maintenance work done on the pipes.
Incomplete question. However, I provided information that could assist you in identifying the main problem or issue addressed in any case study.
Explanation:
First, note that a case study is simply a learning aid that allows one to learn from a real-life scenario.
To determine the main problems of a case study one needs to:
Read the case as many times as possible to become familiar with the message been expressed. For example, by highlighting or underlining the most important facts it can help you to discover the main problem or issue. Check for any facts provided in the case study, by so doing you can identify the most important problems.Thus, by taking these few steps you may be able to determine the main problem in that case study.
Which of the following was an effect of world war 2 on agricultural industry
Answer:
Option C..Farmers saught new technology to help with the workload
hope this helped you
please mark as the brainliest (ㆁωㆁ)
This ball is technology too! It can be
rolled, kicked, or thrown. Is that a need
or a want?
That is an example of a want because you don't need the ball.
what type of diagrams can you create using a compass, a T-square, a triangle, and a protractor?
Answer:
15
Explanation:
A compass may be used to create circles, arcs, bisect lines, angle bisectors, and locate midpoints. By using a compass, a protector is also drawn.
What is the compass?A compass, or more correctly, a pair of compasses, is a tool for technical drawing that may be used to draw arcs or circles. It can also be used as dividers to indicate distances, particularly on maps.
A compass, or more correctly, a pair of compasses, is a tool for technical drawing that may be used to draw arcs or circles. It may also be used as dividers to indicate distances, particularly on maps. Compasses can be used for navigation, mathematics, and other things.
Therefore, a protector is sketched using a compass.
Learn more about the compass, refer to:
https://brainly.com/question/28136911
#SPJ2
What is the capacity of the machine in batches?
Steam enters a two-stage adiabatic turbine at 8 MPa and 5008C. It expands in the first stage to a state of 2 MPa and 3508C. Steam is then reheated at constant pressure to a temperature of 5008C before it is routed to the second stage, where it exits at 30 kPa and a quality of 97 percent. The work output of the turbine is 5 MW. Assuming the surroundings to be at 258C, determine the reversible power output and the rate of exergy destruction within this turbine.
Answer:
1) The exergy of destruction is approximately 456.93 kW
2) The reversible power output is approximately 5456.93 kW
Explanation:
1) The given parameters are;
P₁ = 8 MPa
T₁ = 500°C
From which we have;
s₁ = 6.727 kJ/(kg·K)
h₁ = 3399 kJ/kg
P₂ = 2 MPa
T₂ = 350°C
From which we have;
s₂ = 6.958 kJ/(kg·K)
h₂ = 3138 kJ/kg
P₃ = 2 MPa
T₃ = 500°C
From which we have;
s₃ = 7.434 kJ/(kg·K)
h₃ = 3468 kJ/kg
P₄ = 30 KPa
T₄ = 69.09 C (saturation temperature)
From which we have;
h₄ = [tex]h_{f4}[/tex] + x₄×[tex]h_{fg}[/tex] = 289.229 + 0.97*2335.32 = 2554.49 kJ/kg
s₄ = [tex]s_{f4}[/tex] + x₄×[tex]s_{fg}[/tex] = 0.94394 + 0.97*6.8235 ≈ 7.563 kJ/(kg·K)
The exergy of destruction, [tex]\dot X_{dest}[/tex], is given as follows;
[tex]\dot X_{dest}[/tex] = T₀ × [tex]\dot S_{gen}[/tex] = T₀ × [tex]\dot m[/tex] × (s₄ + s₂ - s₁ - s₃)
[tex]\dot X_{dest}[/tex] = T₀ × [tex]\dot W[/tex]×(s₄ + s₂ - s₁ - s₃)/(h₁ + h₃ - h₂ - h₄)
∴ [tex]\dot X_{dest}[/tex] = 298.15 × 5000 × (7.563 + 6.958 - 6.727 - 7.434)/(3399 + 3468 - 3138 - 2554.49) ≈ 456.93 kW
The exergy of destruction ≈ 456.93 kW
2) The reversible power output, [tex]\dot W_{rev}[/tex] = [tex]\dot W_{}[/tex] + [tex]\dot X_{dest}[/tex] ≈ 5000 + 456.93 kW = 5456.93 kW
The reversible power output ≈ 5456.93 kW.
A boiler is designed to work at 14bar and evaporate 8 kg/s of water. The inlet water to the boiler has a temperature of 400C and at exit the steam is 0.95 dry. The flow velocity at inlet is 10 m/s and at exit 5 m/s and the exit is % m above the elevation at entrance. Determine the quantity of heat required. What is the significance of changes in kinetic and potential energy on the result.
Answer:
Explanation: 2 is thy answer
Most hazardous waste can be disposed of in a landfill. A) TrueB) False
Answer:
This one is false
Explanation:
I just took a test on it..
Most hazardous waste can be disposed of in a landfill. Thus, the above statement is true. Thus, option (A) is correct.
What is the meaning of hazardous waste?A hazardous waste is a waste that has characteristics that make it unsafe or allow it to negatively impact the environment or human health.
Wastes classified as hazardous have characteristics that make them unsafe or potentially damaging to the environment or human health. Liquid, solid, confined gas, and sludge are all examples of hazardous wastes.
Any source that could potentially cause injury, damage, or unfavorable health impacts to someone or something is a hazard.
The majority of hazardous garbage can be dumped in landfills. So, the aforementioned claim is accurate. Therefore, it can be concluded that option (A) is correct.
Learn more about hazardous waste here:
https://brainly.com/question/17210736
#SPJ2
How can you safely lift and support a vehicle
Answer:
Place the jack under the part of the vehicle that it should contact when raised. If you're using jack stands, place them near the jack. If you place your jack incorrectly, you can injure your car. To find the proper place to position the jack for your particular vehicle, check your owner's manual.
Which statement demonstrates the most scientific observation?
Key length is designed to provide desired factor of safety
a. True
b. False
Answer: true
Explanation:
A key is a machine element that us used to connect the element of a rotating machine to a shaft. It should be noted that the key hinders the relative rotation that may take place between the two parts.
Key length is designed to provide desired factor of safety. It should also be noted that the factor of safety shouldn't be much and the key length is typically limited to the hub length.
i need solution for this question please
Select the right answer
Explanation:
the 7th one answer is beacause mercury is bad at sharing electrons
the 8th one's answer is Rhodium
Answer:
1.E aluminum
2.E all
3. Either d or e leaning to e
To create an effective study schedule, a student must
guess the amount of time needed for studying.
O write down all activities and commitments.
O allow the same amount of time each day for studying.
O budget periods of time to study daily, even if it is interrupted.
Answer:
B) write down all activities and commitments.
Explanation:
also i found the answer on quizlet hope this works:))
Answer:
write down all activities and commitments.
Explanation:
i had got the same question on my unit test and it was the answer it was right
A sign that has a white background with a
green panel with white lettering is a
a. general information sign
b. safety instruction sign
c. caution sign
d. danger sign
Answer:
A
Explanation:
general information sign
safety is orange
caution is yellow
danger is red
An eyewash station needs to be located no more than 10 seconds or less than 55 feet away from a work area.
Answer: True is correct
A third-degree burn may look charred and black or dry and white.
Explanation:
An analog baseband audio signal with a bandwidth of 4kHz is transmitted through a transmission channel with additive white noise. The channel is assumed to be distortionless, and the power spectral density of white noise, No/2 is 10 WHz. An RC low-pass filter with a 3-dB bandwidth of 8 kHz is used at the receiver to limit the output noise power. Calculate the output noise power.
Answer:
2k20
Explanation:
4k ✈
Explain how engineering and science-related?
Answer:
While scientists study how nature works, engineers create new things, such as products, websites, environments, and experiences. Because engineers and scientists have different objectives, they follow different processes in their work.
Explanation:
for high-volume production runs, machining parts from solid material might not be the best choice of manufacturing operations because
Answer:
There are actually multiple types of processes a manufacturer uses, and those can be grouped into four main categories: casting and molding, machining, joining, and shearing and forming.
Explanation:
You have a piece of film paper that is 3 in x 5 in. You fix it inside the back of a pinhole camera with a focal length of 5.5 in. You want to use it to take a picture of your team’s mascot – a giant guinea pig that just barely fits in a 4 ft. tall cube. The picture will be taken directly in front, from a stool that places the aperture 2 ft. above the ground. You have to determine how far away the camera must be from your mascot to get a good portrait that fills up the whole film paper, without cutting any part of him off. How far apart should the camera and the mascot be to take the portrait? Show your work.
Answer:
In order to take a portrait, the distance of the mascot from the camera should be approximately 7.33 feet
Explanation:
The size of the film paper = 3 in. × 5 in.
The focal length of the camera = 5.5 in.
The height and width of the guinea pig = 4 ft.
The height of the aperture above the ground = 2 ft.
Therefore, we have;
Magnification = Height of image/(Height of object)
Withe the 3 in. wide film, we have;
Magnification = 3 in./(4 ft.) = 3 in./(48 in.) = 0.0625
Magnification = Length of camera/(Distance of object from pin hole)
∴ Length of camera/(Distance of object from pin hole) = 0.0625
Length of camera = Focal length of the camera = 5.5 in.
Therefore;
5.5 in./(Distance of object from pin hole) = 0.0625
Distance of object from pin hole = 5.5/0.0625 = 88 inches = 7.33 ft
Therefore, the camera should be approximately 7.33 ft. from the mascot to take a portrait.
In this exercise we have to use the magnification knowledge to calculate the distance that the photograph should be taken, thus we have to:
Distance of the mascot from the camera should be approximately 7.33 feet
To calculate the best distance to take the photo, we have that some information must be taken into account such as:
Size of the film paper: [tex](3)*(5) in[/tex] Focal length of the camera: [tex]5.5 in[/tex] Height and width of the guinea pig: [tex]4 ft[/tex] Height of the aperture above the ground: [tex]2 ft[/tex]
Therefore, we have that the formula of magnification is:
[tex]Magnification = Height \ of \ image/(Height \ of \ object)[/tex]
With the 3 in wide film, we have;
[tex]Magnification = 3 in/(4 ft) \\= 3 in/(48 in) = 0.0625 in[/tex]
Rewriting the magnification formula as:
[tex]Magnification = Length \ of \ camera/(Distance \ of \ object \ from \ pin \ hole)[/tex]
Substituting the values already known we have the equation will be matched as:
[tex]Length\ of \ camera/(Distance\ of\ object \ from \ pin \ hole) = 0.0625\\Length \ of \ camera = Focal \ length \ of \ the \ camera = 5.5 in.[/tex]
Therefore;
[tex]5.5 /(Distance \ of \ object\ from \ pin\ hole) = 0.0625 in\\Distance \ of \ object\ from \ pin \ hole = 5.5/0.0625\\ = 88 inches = 7.33 ft[/tex]
See more about distance at brainly.com/question/989117
What allows negative feedback to control a system
Answer:
Negative feedback control of the amplifier is achieved by applying a small part of the output voltage signal at Vout back to the inverting ( – ) input terminal via the feedback resistor
Answer:
The system has parts that sense the amount of output
Explanation:
Apex cirtified
The easiest way to reduce your exposure to dangerous fumes is to keep your head out of a fume plume, making sure that you're breathing the cleanest air possible.
Answer:
keep your head out of a fume plume
Explanation:
According to the guidelines and precaution procedures of OSHA, an acronym for Occupational Safety and Health Administration in the United States of America stated that The easiest way for an individual to reduce his or her exposure to dangerous fumes is to ensure that such person keeps his or her head out of a fume plume.
Hence, in this situation, the correct answer is "keep your head out of a fume plume"
In an intrinsic semiconductor, the number of free electrons is equal to what?
Answer:
The number of holes.
Explanation:
A semiconductor can be defined as a crystalline solid substance that has its conductivity lying between that of a metal and an insulator, due to the effects of temperature or an addition of an impurity. Semiconductors are classified into two main categories;
1. Extrinsic semiconductor.
2. Intrinsic semiconductor.
An intrinsic semiconductor is a crystalline solid substance that is in its purest form and having no impurities added to it. Examples of intrinsic semiconductor are Germanium and Silicon.
In an intrinsic semiconductor, the number of free electrons is equal to the number of holes. Also, in an intrinsic semiconductor the number of holes and free electrons is directly proportional to the temperature; as the temperature increases, the number of holes and free electrons increases and vice-versa.
In an intrinsic semiconductor, each free electrons (valence electrons) produces a covalent bond.
Solve the compound inequality. 3x − 4 > 5 or 1 − 2x ≥ 7
Which one is NOT a benefit of Shine? 1. Less production downtime 2.Happier employees 3. Improved quality 4. Inventory reduction 5. Customer satisfaction
Answer:
Inventory reduction
Explanation:
Shine is a term that deals with the general cleaning and overall maintenance of the workplace. It is used as a part of an organizational theme involving five steps which are often referred to as 5S and it is basically defined as the mainstay of the visual workplace. They are Sort, Set in order, Shine, Standardize, and Sustain.
Hence, in this situation, considering the option that is not a benefit of Shine the correct answer is "Inventory reduction." This is because Shine is not about reducing the inventory levels. It is Sort and Set-in-Order will help reduce inventory.
The answer choice which is NOT a benefit of Shine is:
D. Inventory reduction
According to the given question, we are asked to show the answer choice which is not a direct benefit of Shine and how Shine is used to increase productivity in an office space.
Shine is a term which is used to refer to the general cleanliness of an office space and is a part of organization which is used to improve quality, make the employees happier, and have a less production downtime, etc
As a result of this, we can see that inventory reduction is not a benefit of Shine.
Therefore, the correct answer is option D
Read more here:
https://brainly.com/question/22061432
What is the transfer of energy from one object to another?
Answer:
Kinetic Energy
Explanation:
Energy is transferred from one object to another when a reaction occurs. Energy can be transferred from one object to another as heat, light, and motion.
You are designing an airplane to carry liquid cargo that will slosh and move side to side in its container. This could make the plane unstable. What type of airfoil would you use for the wing? Why. Answer in a full sentence or more
A 5000-ft long X-65 pipeline is laid down on seabed with two PLETS (One at each end). The pipe OD=7-in with 0.5-in wall thickness. The pipeline was laid at environmental temperature of 40 °F (As- laid temperature). When pipeline is put into operation, the oil flow was produced at 140 °F. If the thermal expansion coefficient of the pipe material is 6.5*10-/°F and its modulus of elasticity is 30,000 ksi, determine the compressive load applied by the pipeline on a PLET due to its thermal expansion. Assume no temperature change and no seabed friction along the pipeline span.
Answer: 199.1 kip
Explanation:
Given that
Outer diameter is Do = 7 in
Inner diameter Di = ( Do - ( 2×0.5)) = 6 in
Length = 5000 ft = 60000 in
Now change in length of the pipe due to temperature difference
SL = L∝ΔT
= 60000 × 6.5×10^-6(140-40)
SL = 39 in
Also
sL = PL/AE
A = cross sectional area of pipe = π/4(Do^2 - Di^2)
so
P = SL×A×E / L
= (39 × π/4(7^2 - 6^2)×30000) / 60000
= 199.1 kip
compressive load applied by the pipeline on a PLET due to its thermal expansion is 199.1 kip
A standard carbon resistor has a gold band to indicate + 5% tolerance. If its resistance is 3,500 , what are the upper and lower limits for its resistance? OA . 3495 - 3505 2 OB. 3300 Q - 3600 0 OC. 3325 N - 3675 OD 3450 - 35500
Answer:
C. 3325 Ω - 3675 Ω
Explanation:
5% of 3500 Ω is ...
0.05 × 3500 = 175
The lower limit is this amount less than the nominal value:
3500 -175 = 3325
The upper limit is the nominal value plus the tolerance:
3500 +175 = 3675
The lower and upper limits are 3325 Ω and 3675 Ω, respectively.
Wheel grinders need be equipped with an
Answer:
wheel guard
Explanation:
to protect our hands and reduce spark
A company that produces footballs uses a proprietary mixture of ideal gases to inflate their footballs. If the temperature of 230 grams [g] of gas mixture in a 15-liter [L] tank is maintained at 465 degrees Rankine [°R] and the tank is pressurized to 135 pound-force per square inch [psi], what is the molecular weight of the gas mixture in units of grams per mole
Answer:
The molecular weight of the gas mixture is 35.38 g/mol.
Explanation:
The molecular weight of the gas can be found using the following equation:
[tex] M = \frac{m}{n} [/tex]
Where:
m: is the mass = 230 g
n: is the number of moles
First, we need to find the number of moles using Ideal Gas Law:
[tex] PV = nRT [/tex]
Where:
P: is the pressure = 135 psi
V: is the volume = 15 L
R: is the gas constant = 0.082 L*atm/(K*mol)
T: is the temperature = 465 °R (K = R*5/9)
[tex]n = \frac{PV}{RT} = \frac{135 psi*\frac{1 atm}{14.6959 psi}*15 L}{0.082 L*atm/(K*mol)*465*(5/9) K} = 6.50 moles[/tex]
Finally, the molecular weight of the gas is:
[tex] M = \frac{m}{n} = \frac{230 g}{6.50 moles} = 35.38 g/mol [/tex]
Therefore, the molecular weight of the gas mixture is 35.38 g/mol.
I hope it helps you!