The pedal does not push the master cylinder farther into the master cylinder bore.
What is the advantage of using a left foot?
The theory used in this question is the principle of using a left foot to apply pressure to the brake pedal while seating the brake pads. By using the left foot on the brake pedal while the right foot applies pressure, the technician is able to prevent the master cylinder from being pushed farther into the master cylinder bore.
The steps for this process are as follows:
1. Place the brake pads into the caliper.
2. Place the left foot on the brake pedal.
3. Use the right foot to apply pressure to the pedal, pushing it down slowly.
4. Allow the pressure from the left foot to prevent the master cylinder from being pushed farther into the master cylinder bore.
5. When the brake pads are seated correctly, release the pressure from the pedal.
To learn more about pressure to the brake pedal refer :
https://brainly.com/question/8492751
#SPJ4
the hydraulic lit in a car repair shop has an output diameter of 22.8 cm and is to lift cars up to 1620 kg. determine the fluid gage pressure in kpa that must be maintained
Answer:
To determine the fluid gage pressure that must be maintained in the hydraulic lift, you need to use the equation for force, which is:
Pressure = Force / Area
Where:
Pressure is in units of kPa (kilopascals)
Force is in units of N (newtons) and is equal to the weight of the car (1620 kg) multiplied by the acceleration due to gravity (9.81 m/s^2)
Area is in units of m^2 (square meters) and is equal to the output diameter of the lift (22.8 cm) converted to meters (0.228 m)
So the pressure that must be maintained is:
Pressure = (1620 kg * 9.81 m/s^2) / (0.228 m^2)
Pressure = (15,847.2 N) / (0.228 m^2)
Pressure = 69,844 kPa
So the fluid gage pressure that must be maintained is 69,844 kPa.
on farm tractor how do you determin whether you have a fautlty aitrnator or voltage regulator in your farm tractor
To determine whether you have a faulty alternator or voltage regulator in your farm tractor, you should first check the battery voltage.
A healthy battery should have a voltage of 12.6 volts or higher. If the voltage is lower than 12.6 volts, then you should inspect the alternator and voltage regulator for any signs of damage or wear.
Additionally, you can use a multi-meter to test the voltage output from the alternator and voltage regulator to determine if they are working correctly. If the voltage output is not within the correct range, then the alternator or voltage regulator may be faulty and need to be replaced.
Learn more about voltage regulator:
https://brainly.com/question/15875284
#SPJ4
what are the differences between a regular operating system and a real time operating systems? g
Real-time operating systems are made to execute vital applications dependably and at precisely the right moment, in contrast to operating systems like Windows.
What is the same between a real-time system and an actual operating system?When time restrictions are set and closely adhered to, real-time operating systems are used. It implies that there is very little time for consideration and action. Additionally, the system must do the work within a certain amount of time or else it will fail.Real-time operating systems, like VxWorks, vary from non-real-time operating systems like Windows and Linux in that they have fast guaranteed interrupt latencies and thread preemption times.Real-time operating systems are made to execute vital applications dependably and at precisely the right moment, in contrast to operating systems like Windows, which are made to keep user responsiveness when multiple programmes and services are running (ensuring "fairness").To learn more about operating system refer to:
https://brainly.com/question/1033563
#SPJ4
compare distributed database design strategies with respect to reliability, expandability, communications, overhead costs, manageability, and data consistency.
A distributed database refers to a database management system in which all databases are not connected on the same server.
What are the characteristics of distributed database?In comparison to centralized databases, distributed databases are more reliable. In the event of a database failure in a centralized database, the system comes to a halt. When a distributed database fails, the system continues to function, albeit with reduced performance until the problem is resolved.DDBMS's primary function is to keep track of data distribution, fragmentation, and replication by expanding the DDBMS catalog.Every read, regardless of which node it comes from, returns the data of the most recent write. Network failure is unavoidable in a distributed database, and a database must ensure that it can continue to run even if a partition fails.Often, expensive software is required to ensure data transparency and coordination across multiple sites.A distributed database management system (DDBMS) that is centralized manages distributed data as if it were stored in a single physical location. Data storage on-site lowers communication costs for data manipulation in distributed databases. In centralized databases, local data storage is not possible.To learn more about distributed database refer to :
https://brainly.com/question/28271067
#SPJ4
A brass rod 100 mm long and 5 mm in diameter extends horizontally from a casting at 200oC. The rod is in air with T?=20oC and h=30 W/(m2 K).
a. What is the temperature of the rod at 25, 50, 75, and 100 mm from the casting? Assume that the fin tip is approximately adiabatic.
b. What is the rate of heat transfer from the fin?
c. What would be the rate of heat transfer from a 5 mm diameter circle of the casting surface
without a fin?
The temperature distribution is the result of the linear heat flow equation [1]: (1) T t = 2 T x 2, where T=T(x,t) is the temperature at a point in space -time(x ,t) and is the thermal diffusivity Answer: 156°C, 128°C and 106.5°C
What is the temperature distribution?
Where L is the length (100mm = 0.
1 m), x is the distance from the rod end, k is the conductivity of the brass, i.e. 133 W/m.
m = (hp/kAc) 1/2
circumference, p = π*D, where D is the diameter (5 mm = 0.
005m) to Pole, Ac = π*D2/4
m = (hp/kAc) 1/2
m = 13.43 m (-1)
m = 13.
43 m⁻1
Nota :
coshmL = cosh(13,43*0,1) =
h/mk = 30/(13.43*133) = 0.0168
Tb is the difference between casting temperature and ambient temperature: Tb = 200 - 20 = 180°C
p Then T ∞
Trod = 106.5 °C
To learn more about the temperature, visit
brainly.com/question/2935496
#SPJ4
Resolve the force F1 into components acting along the u and v axis and determine the magnitude of the components.
The magnitude of the components of F1 is:
F1v= 129 N F1u= 183 NTo solve this exercise we need to draw the vector components for F1 and in this way we can express the F1 vector in function of its components:
F1= F1v + F1u
Now using the Sine law we can find the F1v and F1u values:
The sine lawThe sine law states that the ratio of the length of any side of a triangle to the sine of its opposite angle is equal for all sides and angles of the triangle.
In other words, for any triangle ABC, the ratio of side a to the sine of angle A is equal to the ratio of side b to the sine of angle B, and the ratio of side c to the sine of angle C. This law is an important tool in trigonometric calculations and is used to calculate the unknown sides and angles of a triangle when given the known sides and angles.
F1v/sin(30°) = 250/Sin(105°)
F1v= 129 N
F1u/Sin(45°) = 250/Sin(105°)
F1u= 183 N
Learn more about Sine law:
https://brainly.com/question/4372174
#SPJ4
A check that is made payable to a specific person is
Group of answer choices
a special endorsement
a blank endorsement
a restrictive endorsement
none of the above
A special endorsement is a check made payable to a specific person. A special endorsement is another type of check endorsement that is used by a payer to give the check to a specific individual.
What is special endorsement?
The following are the special endorsement instructions: "Pay to the order of [recipient's name]," then sign below. It is possible to pay someone else with a check made out to you. In essence, you are transferring the funds associated with the check from the payee to someone else. This is referred to a special endorsement. If a check or check draft is returned due to a missing endorsement, it is because the depositor did not endorse the item, not the account holder who issued the check.
An endorsement is indeed a signature or stamp that appears on a back side of the check.
To learn more about special endorsement refer to :
brainly.com/question/20115196
#SPJ4
With the aid of block diagrams, construct an open loop and a closed loop
control systems. Then, identify the differences between the two control
structures.
An open loop control system is a type of control system in which the output does not affect the control action. The block diagram for an open loop control system is shown below:
[Input] --> [Controller] --> [Plant] --> [Output]
A closed loop control system is a type of control system in which the output is used to adjust the control action. The block diagram for a closed loop control system is shown below:
[Input] --> [Controller] --> [Plant] --> [Output] --> [Feedback] --> [Controller]
What is the open and closed loop about?In the open loop diagram, the input signal is passed through the controller, which generates an output signal that is used to control the plant. The plant then produces the final output, but this output is not fed back to the controller to adjust the control action.
In the close diagram, the input signal is passed through the controller, which generates an output signal that is used to control the plant. The plant then produces the final output, which is fed back to the controller. This feedback signal is used to adjust the control action, allowing for more precise and accurate control of the plant.
Therefore, main difference between the two control structures is the presence of feedback.
Learn more about open loop from
https://brainly.com/question/17924509
#SPJ1
consider the following statement, which is intended to create an arraylist named years that can be used to store elements both of type integer and of type string.
The alternative that can be utilized to change the /* missing code */ in order for the statement to compile correctly is.
List of years, The Java programming language is the subject of this query. As can be seen from the query, an ArrayList is involved. In Java, the syntax to declare an ArrayList with no specific data type is as follows: ArrayList [Name of the Lists] = new ArrayList(); The list name is now "years" in the query. Thus; The appropriate statement to replace any missing code in order to avoid mistakes is; ArrayList years is a replacement option that can be used to fill in any missing code, ensuring that the statement compiles successfully. Simply put, resizable arrays are ArrayLists. The statements (b) new ArrayList() and (c) I and III only are capable of substituting for the missing code, respectively. ArrayList creation syntax is as follows: new ArrayListType>() using the argument ArrayListType> str;
Learn more about Java here:
https://brainly.com/question/29032527
#SPJ4
The von Neumann bottleneck:
A. was first invented by John Atanasoff.
B. describes the single processor-memory path.
C. is eliminated when multiple processors/cores are used.
D. creates collisions on an I/O bus.
The von Neumann bottleneck is describes the single processor-memory path.
What is single processor-memory?A single processor system contains only one processor. So only one process can be executed at a time and then the process is selected from the ready queue. Most general purpose computers contain the single processor systems as they are commonly in use.As in the above diagram, there are multiple applications that need to be executed. However, the system contains a single processor and only one process can be executed at a time.Multiprocessor Systems. Description. The name itself is saying that the single processor system contains only one processor for processing. For this also the name itself indicates that the multiprocessor system contains two or more processors for processing.To learn more about multiprocessor refer to :
https://brainly.com/question/14081253
#SPJ4
in the structure shown, an 8-mm-diameter pin is used at a, and 12-mm-diameter pins are used at b and d. knowing that the ultimate shearing stress is 100 mpa at all connections and that the ultimate normal stress is 250 mpa in each of the two links joining b and d, determine the allowable load p if an overall factor of safety of 2.7 is desired.
To determine the allowable load P, we need to calculate the shear and normal stresses at each connection. The shear stress at each connection can be calculated using the equation τ = P/A, where P is the load and A is the area of the pin.
The normal stress at each connection can be calculated using the equation σ = P/A, where P is the load and A is the cross-sectional area of the link. Once the shear and normal stresses have been calculated, we can compare them to the ultimate shear and normal stresses to determine the allowable load. The allowable load will be the load that produces a shear and normal stress that is equal to or less than the ultimate shear and normal stresses, multiplied by the factor of safety.
To calculate the allowable load, we need to first calculate the shear and normal stresses at each connection. The shear stress at each connection can be calculated using the equation τ = P/A, where P is the load and A is the area of the pin. The area of the pin can be calculated using the equation A = πr2, where r is the radius of the pin. The normal stress at each connection can be calculated using the equation σ = P/A, where P is the load and A is the cross-sectional area of the link. The cross-sectional area of the link can be calculated using the equation A = bh, where b is the width of the link and h is the height of the link. Once the shear and normal stresses have been calculated, we can compare them to the ultimate shear and normal stresses to determine the allowable load. The allowable load will be the load that produces a shear and normal stress that is equal to or less than the ultimate shear and normal stresses, multiplied by the factor of safety.
Learn more about shear and normal stresses here
https://brainly.com/question/23270001
#SPJ4
your company is confused and needs your technical assistance. they have given you different scenarios and want to know if they should use a spreadsheet or a dbms. analyze each situation and select either dbms or a spreadsheet.
Statistical Comparisons Select Worksheet 2. Complex DBMS Queries 3. Summary Report Select 4. Calculations Select v 5. Mortgage Calculations Select 6.
What is a DBMS?
Data management Select V 7. DBMS inventory control 8. Data security control Select 9. Small DBMS data storage V 10. Class selection Grade calculation. A database management system (or DBMS) it is essentially nothing more than a computerized data storage system. System users have the ability to perform various types of operations on this system to manipulate database data or manage the structure of the database by yourself. Database management systems (DBMS) are classified according to their data structures or types. There are several types of databases that can be used on a mainframe to take advantage of z/OS®: inverted list, hierarchical, network or relational. Mainframe sites typically use a hierarchical model, if a data structure ( not the data values ) the data required by the application is relatively static.
For example, a BOM database structure always contains a top-level assembly part number and multiple levels of components with subcomponents. The structure typically includes component forecasts, cost and price data, etc.
To learn more about DBMS refer to:
brainly.com/question/24027204
#SPJ4
According to the National EMS Scope of Practice Model, an EMT should be able to:
A. assist a patient with certain prescribed medications.
B. insert a peripheral intravenous (IV) line and infuse fluids.
C. administer epinephrine via the subcutaneous route.
D. interpret a basic electrocardiogram (ECG) rhythm and treat accordingly.
Emergency services should be able to help you with some prescribed medications.
What are medications?
A medication is a drug used to diagnose, treat, or prevent a disease becomes . nIt is also called medicine, medicine, pharmaceutical medicine, or simply medicine. An important field of medicine is pharmacotherapy, that is, drug therapy, the advancement of which depends on the science of pharmacology and pharmacy to be effective Pharmaceutical companies, academic scientists and governments engage in complex and costly drug research and development initiatives. Due to the complex process involved in moving a drug candidate from discovery connected to commercialization, the partnership is now considered best practice. Governments typically control how medicines are advertised, what medicines are allowed to be sold and, in some places, how much the medicines cost.
Disposal of old medicines and medicine prices have become controversial issues.
To learn more about medications refer to
brainly.com/question/12646017
#SPJ4
usaf europe driving when following another vehicle it is left to your discretion whether or not to dim your high beams to reduce the glare in his or her rearview mirror.
If you are following another vehicle, you have the option to change your bright headlights to low beams in order to prevent blinding the driver.
It's critical to keep the driver of the car you're following in mind whenever you follow another vehicle. Dimming your high lights, if they are on, is one technique to make sure they are safe. This will make it easier for them to see the road because it will lessen the glare in their rearview mirror. Many drivers enjoy the courtesy of dimming high lights since it might allow them to maintain a safe driving environment. However, the decision to do so or not is ultimately up to you. If you believe it to change your bright headlights to low beams in order to prevent blinding the driver.
Learn more about low beams here-
brainly.com/question/29946531
#SPJ4
assignment definition: the exploring innovation is a team assignment that requires each team to focus on 1 technology innovation area of interest and write an informative essay of 5-7 pages that resembles a media article supported by recent innovation news such as those that can be found on the web. the article should include illustrations using visual material such as images, tables and charts and may also include links to relevant videos that found on the web. the team should also assign one or more team member(s) to create the summary of 5 minute video/narrated powerpoint of this week's team case study and drop the file in the drop box or include a link of that video / narrated powerpoint as a part of the case study report! review the exploring innovation media article overview page under introduction
An organization can achieve enormous success through innovation. So, a new product could be unsuccessful on the market.
An organization can achieve enormous success through innovation. As a result, a new product may not succeed on the market since it does not offer genuine value to customers. Innovations need to clearly create value for various buyer groups as well as provide that value in order to succeed. The issue is that delivering value to customers may result in or be accompanied by significant financial losses for the associated organization. Innovation, however, can help an organization achieve significant success. As a result, the cultures of innovative organizations rarely accept that they are good enough. This thereby accepts risk in the pursuit of improvement.
Learn more about Innovation here:
https://brainly.com/question/30295894
#SPJ4
At a site owned by Company X, it is decided to remediate a plume using a double trench system as shown below. A plume lies between the two trenches in a sand layer that is capped by a relatively impermeable clay layer. Nutrient and oxygen laden water will be injected in the trench on the right. The water will flush from right to left and be pumped out of the left trench. To ensure maximum biodegradation, it is best if the sand layer stays saturated. Thus, the trench on the left will be pumped just enough to keep the sand layer saturated. The trench on the right will be kept as full as possible. For the sand layer, assume than n = 0.35 and k = 0.01 cm/s.
(not to scale)
90 ft
2 ft
Clay
10 ft
Plume
Bedrock
a) For a one ft thick slice of the sand layer, how much water would need to be pumped to flush through one pore volume?
b) How long would it take (in days) to pump five pore volumes of water through the sand?
Check out Erich Maria Remarque's All Quiet on the Western Front for first-person tales of the pain experienced during trench warfare (1929).
No man's land, or the western front, was the space between the opposing forces' trenches during World War I. In the First World War, trench fighting was horrifying and terrible. Any attempts to breach and attack the opposite side were typically met with the fire of machine guns, as the forces had dug into trenches facing each other. Check out Erich Maria Remarque's All Quiet on the Western Front for first-person tales of the pain experienced during trench warfare (1929). For first-person stories of the misery experienced during the trench combat, you might want to read Erich Maria Remarque's 1929 book All Quiet on the Western Front.
Learn more about Trenches here:
https://brainly.com/question/13646182
#SPJ4
you may pass on the right of another vehicle: when traveling either on a multilane highway or on a street with an available turning lane. only when traveling on a multilane highway with two or more lanes of traffic traveling in the same direction. only when the other vehicle is making or is about to make a left turn and a lane is provided for you to pass on the right.
You may pass on the right of another vehicle when traveling either on a multilane highway or on a street with an available turning lane. Passing on the right is only allowed when there is an available lane for you to pass in.
When traveling on a multilane highway with two or more lanes of traffic traveling in the same direction, you may pass on the right of another vehicle if there is an available lane for you to pass in. When traveling on a street with an available turning lane, you may pass on the right of another vehicle if the other vehicle is making or is about to make a left turn and a lane is provided for you to pass on the right. It is important to note that passing on the right is only allowed when it is safe to do so. You should always check your mirrors and blind spots before passing on the right, and you should always use your turn signal to indicate your intention to pass. Additionally, you should always be aware of the speed limit and other traffic laws when passing on the right.
Learn more about multilane highways here
https://brainly.com/question/15586253
#SPJ4
In the following Python commands, what does the 0.99 represent?import scipy.stats as stst.norm.interval(0.99, 0.50, 0.05)Question 2 options:confidence levelstandard errorproportionmean
Python program to calculate the confidence interval given the values of Standard error of the proportion, the arithmetic mean, and the standard deviation. Correct answer: Standard Error of the Proportion.
What is the standard error of the proportion of a statistical sample?It is a critical value that determines the limit of values, that is, those that are inside or outside the acceptance region, thus defining the limits of a confidence interval. Below is an example in python code.
Python codeimport numpy as n
from scipy import stats
# Standard Error of the Proportionstandard_error = 0.99
# arithmetic averagearithmetic_average = 0.50
# sample standard deviationsample_standard_deviation = 0.05
# calculating confidence intervalconf_int = stats.norm.interval(standard_error, arithmetic_average, sample_standard_deviation)
# Outputprint("Standard Error of the Proportion: ",standard_error)
print("Arithmetic average: ",arithmetic_average)
print("Sample standard deviation: ",sample_standard_deviation)
print("Confidence interval: ",conf_int)
To learn more about Confidence interval see: https://brainly.com/question/15712887
#SPJ4
Which of the following best describes teachers in the later developmental stages of technology integration?
a. Adjusting the fundamental nature of their instruction.
b. Using technology to support traditional instruction.
c. Adapting instruction to technology.
d. Substituting paper-and-pencil activities with technology.
Making decisions about core technology/protocols and circuit capacity during the technical design phase of a network is interconnected.
Network design is the planning and construction of a communications network. Network design begins with the identification of business and technical needs before network installation. Information concealment and hierarchical design are examples of time-tested principles that apply to good network architecture. Fundamental network protocols that use data encapsulation serve as one example of this. Changes in the lower layers have no impact on the upper layers since they operate in secrecy from the higher layers (i.e. applications). In addition to managing computer systems, they also install and support them. This list could also include intranets, network segments, local area networks (LANs), wide area networks (WANs), and other data transmission technologies.
Learn more about Network design here:
https://brainly.com/question/30052056
#SPJ4
what makes social engineering such an effective technique for hackers?
Social engineering is an effective technique for hackers because it exploits human interaction and psychology to gain access to sensitive information and systems.
What are the key components of a successful social engineering attack? The key components of a successful social engineering attack include psychological manipulation, research, and execution. Psychological manipulation involves using tactics such as authority, fear, flattery, or urgency to influence the target’s decision-making. Research involves gathering information about the target, such as their job title, interests, and habits. This enables the attacker to tailor their approach to the target and to create a sense of familiarity or trust. Finally, execution requires carrying out the attack with a well-crafted message, often via email or phone. The message should be tailored to the target, and should be clear, concise, and persuasive. Additionally, the attacker should be confident, friendly, and persistent. With these components, a successful social engineering attack can be carried out.To learn more about social engineering refer to:
https://brainly.com/question/30203031
#SPJ4
g this word is a good description of what engineers do: this word is a good description of what engineers do: discover design delegate dictate
A person who has received training and expertise in the design, manufacture, and usage of engines or machines, as well as in any of the many engineering specialties.
What is the meaning of the word engineering?Noun use of information from the pure sciences, such as physics or chemistry, in practical ways, such as when building chemical plants, bridges, engines, and other structures. the behaviour, endeavour, or line of employment of an engineer.The usage of "an" to denote a single countable noun that is random when a word has a vowel sound makes option C the correct choice. Thus, "An Engineer" is grammatically appropriate.A great engineer is able to make wise decisions about what is most important at any given time. They are not just technology-focused, but also customer-focused. They have high aspirations and make sure to solve significant, worthwhile problems. Not simply what people decide to do, but also how they choose to accomplish it, is covered by this.To learn more about engineering refer to:
https://brainly.com/question/17169621
#SPJ4
a small air compressor operates on a 2.3 hp (horsepower) electric motor for 8.2 hours a day. how much energy is consumed by the motor daily? 1 hp equals about 750 watts. answer in units of j. 005 (part 2 of 2) 10.0 points if electricity costs 21 cents per kilowatt-hour, how much does it cost to run the compressor each day? answer in units of cents
The daily operating expense for the compressor is 50922000J.
Multiplying 2.3 * 750 to get 1725 watts per second by 8.2 hours (8.2 * 3600) to get 50922000 J.
Excellent. Part 2 follows:
Therefore, for 8.2 hours, your motor operates at 1725 W (or 1.725 kW).
Analyze the units. We possess kilowatts. KWH is what we need. Multiply together!
At a cost of $0.22 per kWh, 1.725 x 8.2 = 14.145 kWh equals:
14.145 * .21 = $2.97
3600000 J is equal to 1 kilo Watt hour times 3600 seconds, or 21 cents for 3600000 Jules of energy.
All day long, we utilized Jules, therefore 50922000 / 3600000 *.21 = $2.97
E = 2.3 hp*750 watts*60seconds*60minutes*8.2hours = 50922000J
To learn more about Horsepower refer to:
brainly.com/question/29649552
#SPJ4
The compressor's daily operating cost is 50922000J.
How much does it cost per day to operate the compressor?
8.2 hours (8.2 * 3600) divided by 2.3 * 750, or 1725 watts per second, yields 50922000 J.
Excellent. Following is Part 2:
Thus, your motor runs at 1725 W for 8.2 hours (or 1.725 kW).
Investigate the units. Kilowatts belong to us. What we require is KWH. multiply by two!
1.725 x 8.2 = 14.145 kWh at a price of $0.22 per kWh equals:
14.145 * .21 = $2.97
One kilo Watt hour times 3600 seconds is 3600000 J, or 21 cents for 3600000 Jules of energy.
We used Jules all day long, therefore 50922000 / 3600000 *.21 = $2.97
E = 2.3 horsepower * 750 watts * 60 s * 60 m * 8.2 hr = 50922000J
To learn more about compressor refer to:
https://brainly.com/question/29345949
#SPJ4
A large airline appointed an engineer to be the link between the company's research and development department and the government contractor who is sponsoring the designing and prototyping of a new fighter airplane. According to Mintzberg, the engineer appointed by the airline is in the role of a ____
A Liaison is a role that involves connecting two or more parties and facilitating communication between them. The engineer appointed by the airline is responsible for connecting the company's research and development department.
The engineer will be responsible for ensuring that the two parties are kept informed of each other's progress and that any issues or concerns are addressed in a timely manner. The engineer will also be responsible for providing feedback and advice to both parties in order to ensure that the project is completed successfully.
The engineer will also be responsible for ensuring that the project is completed within the agreed-upon timeline and budget. The engineer will need to be able to effectively manage the project and coordinate the efforts of both parties in order to ensure that the project is completed on time and within budget. The engineer will also need to be able to identify any potential risks or issues that may arise during the project and take steps to mitigate them. Finally, the engineer will need to be able to provide regular updates to both parties on the progress of the project and ensure that any changes or modifications are communicated in a timely manner.
Learn more about Liaison here
https://brainly.com/question/30244734
#SPJ4
fill in the blank. g today, it can be difficult to choose the best material for a given application because: today, it can be difficult to choose the best material for a given application because:___we have so few different materials from which to choose.___we have so many different materials from which to choose.
Identify product design requirements, Identify product element design requirements, Identify potential materials.
What is mean by materials?The term "material" describes something that is used to create another item. Cloth or any other item made of matter that exists in the physical world can be referred to as material. As a noun and an adjective, "material" has numerous more meanings.
Any substance used to create an object is referred to as a material. Different materials include clay, glass, paper, wax, air, water, and chalk. Matter is the basis of all materials.
The choice of materials is a crucial component in product creation. A suitable material must satisfy a number of fundamental requirements, including effective manufacturability, performance, dependability, non-degradability, and recyclability.
To learn more about material refers to;
https://brainly.com/question/27666749
#SPJ4
the first step in checking the operation of the brake pad wear indicator system is to: group of answer choices check that the sensor or scratcher is not too close to the rotor. research the service information to determine the type of brake pad wear indicator system that is used. check that the sensor is grounded with a test lead. test the system.
The first step in checking the operation of the brake pad wear indicator system is to research the service information to determine the type of brake pad wear indicator system that is used.
Different types of brake pad wear indicator systems use different types of sensors or scratchers, and it is important to know which type of system is being used in order to properly check its operation. Once the type of system is known, the next step is to check that the sensor or scratcher is not too close to the rotor. If the sensor or scratcher is too close to the rotor, it may not be able to detect the wear of the brake pads. Additionally, the sensor or scratcher should be checked to ensure that it is properly grounded with a test lead. Finally, the system should be tested to ensure that it is functioning properly. This can be done by applying the brakes and checking the operation of the indicator light or other warning system. If the system is functioning properly, the indicator light or other warning system should activate when the brake pads are worn.
Learn more about indicator system here
https://brainly.com/question/29654868
#SPJ4
first, place each link in the chain of infection with its example. second, correctly order the examples, with the first stage at the top.
First, place each link in the chain of infection with its example in the following order, with the first stage at the top:
SourceMode of TransmissionPortal of ExitPortal of EntrySusceptible HostSecond, correctly order the examples, with the first stage at the top:
Source: Person with the disease.Mode of Transmission: Physical contact with an infected person.Portal of Exit: Lungs, saliva, or other bodily fluids.Portal of Entry: Inhaling droplets or touching a contaminated surface.Susceptible Host: Person who has not been exposed to the pathogen.Learn more about the chain of infection:
https://brainly.com/question/3121356
#SPJ4
In a poll of 1000 randomly selected voters in a local election, 625 voters were against school bond measures. What is the sample proportion p? What is the margin of error m for the 99% confidence level?
Answer:
p = 625 / 1000 = 0.625
m = 2.576 * sqrt((0.625 * (1 - 0.625)) / 1000) = 0.03
Explanation:
The sample proportion p is the proportion of voters in the sample who were against school bond measures. To calculate this, divide the number of voters against the bond measures (625) by the total number of voters in the sample (1000):
p = 625 / 1000 = 0.625
The margin of error m for a sample proportion at the 99% confidence level can be calculated using the formula:
m = zsqrt(p(1-p)/n)
where z is the z-score for the desired level of confidence (for a 99% confidence level, z = 2.576), p is the sample proportion, and n is the sample size.
m = 2.576 * sqrt((0.625 * (1 - 0.625)) / 1000) = 0.03
So the margin of error for this poll at the 99% confidence level is 0.03.
If I ue proper in-text citation and reference along with quotation mark for direct quote, I will not be plagiarizing.
You are not engaging in plagiarism if you have accurately cited the source when paraphrasing or quoting. However, using the right word is essential. You must abide by the rules of your chosen citation style (such as APA or MLA) to prevent plagiarism.
Do I need to cite the source when using a straight quotation but not a paraphrase?
According to some pupils, a source should only be cited when a direct quote is used. That's not right at all! Just because you put someone else's idea into your own words doesn't make it your own creation. Even if you paraphrase, the original author must still be given credit.
I'll also paraphrase: You are still plagiarizing if you change the order of words or concepts from the original source and incorporate parts of your own words mixed in with the original ones, even if you cite the source.
To learn more about paraphrase to refer:
brainly.com/question/29890160
#SPJ4
determine the pressure at the deepest part of lake tahoe. the lake's surface elevation is 6225ft, assume that the conditions of the us standard atmosphere prevail at surface of the lake
Two conclusions can be inferred from the posed query, The distance from Lake Titicaca's surface to its deepest point is -922 feet.
The lake's deepest point is 11542 feet above sea level. Every distance above sea level is positive, and every distance below sea level is negative. Since the lake's lowest point is above sea level and its surface is above it, the Surface will therefore also be above sea level. Lake surface elevation is equal to the sum of the distance from the sea level to the deepest point in the lake and the distance from the surface to that point. = 11542 + 922. = 12464 feet. This means that the lake's elevation above sea level is 12464 feet. Two conclusions can be inferred from the posed query, The distance from Lake Titicaca's surface to its deepest point is -922 feet.
Learn more about The lake's deepest point here:
https://brainly.com/question/5185746
#SPJ4
FILL IN THE BLANK. Traditional file systems use ________, files, and documents.
Traditional file systems use directories, files, and documents. Directories are used to organize files and documents into a hierarchical structure.
Files are the actual data stored in the file system, and documents are the files that contain text or other information. Directories are used to organize files and documents into a hierarchical structure, which makes it easier to find and access the data stored in the file system. Files are the actual data stored in the file system, and documents are the files that contain text or other information. Documents can be used to store text, images, audio, video, and other types of data. Directories are organized into a hierarchical structure, with each directory containing one or more subdirectories. Each subdirectory can contain files and documents, and each file and document can contain data. The hierarchical structure of the file system makes it easier to find and access the data stored in the file system.
Learn more about Traditional files here
https://brainly.com/question/20292126
#SPJ4