what is the process that involves repair on an emergency or priority basis? breakdown maintenance emergency maintenance failure maintenance preventive maintenance priority maintenance

According to the question the proper use of the id instruction would be: ld r24, X.

The other options provided (Id r24, r26, ld r24, varName, and ld r24, 252) do not appear to be valid uses of the id instruction and may be incorrect or syntactically incorrect depending on the specific programming language or context in which they are used.

However, without more context or information about the specific programming language or assembly instruction set being referred to, it is difficult to provide a definitive answer. It is important to consult the documentation or resources specific to the programming language or instruction set being used to ensure proper usage of instructions.

To learn more about instruction
https://brainly.com/question/29405960
#SPJ11

In the given scenario, using the Rankine cycle, we are tasked with determining various parameters and improvements for a power plant. In the initial setup, where a single reversible turbine is used and the outlet to the condenser is saturated vapor at 25 KPA, we need to find the operation pressure of the boiler, the thermal efficiency, and the circulation rate to provide 1 MW net power output.

For the first part, since the outlet of the turbine is saturated vapor, we can use the saturation properties of water to find the corresponding temperature at 25 KPA. Knowing this temperature allows us to determine the operation pressure of the boiler, which would be the same as the saturation pressure corresponding to the desired temperature of 500°C.  To calculate the thermal efficiency, we need to use the Carnot efficiency formula. The thermal efficiency is given by the net work output divided by the heat input. The net work output can be obtained from the 1 MW power output, and the heat input can be calculated using the enthalpy difference between the boiler and the condenser.

To determine the circulation rate for 1 MW net power output, we need to use the equation: net power output = circulation rate × (work output per unit mass).

. Rearranging the equation, we can solve for the circulation rate.

In the second part, where two reversible turbines are used with different inlet conditions, we need to find the improvements in efficiency and circulation rate relative to the previous case. By utilizing two turbines, the expansion of steam occurs in two stages, which allows for better utilization of the thermal energy and improved overall efficiency. The specific improvements in efficiency and circulation rate can be calculated by comparing the work output and circulation rate obtained in the new cycle to the values obtained in the initial single turbine cycle. These improvements are a result of better energy extraction and utilization within the system.

To learn more about Rankine cycle refer:

https://brainly.com/question/29835593

#SPJ11

Two primary features of e-business components are online transactions and customer relationship management.

Online transactions refer to the buying and selling of goods and services over the internet. This includes online shopping, online banking, and other online financial transactions. The ability to conduct transactions online has greatly increased the convenience and efficiency of commerce, allowing businesses to reach a global market and consumers to make purchases from the comfort of their own homes.

Customer relationship management (CRM) is another key component of e-business. This refers to the practices, strategies, and technologies that companies use to manage and analyze customer interactions and data throughout the customer lifecycle. CRM systems help businesses to improve customer retention, increase customer satisfaction, and drive sales growth by better understanding customer needs and preferences, as well as tracking and responding to customer feedback. E-businesses rely heavily on CRM tools to develop and maintain long-term relationships with customers in an increasingly competitive digital landscape.

To learn more about global market : brainly.com/question/26958871

#SPJ11

As shown in the accompanying figure, the CompareValidator validation control can be used to ensure two passwords match.

The CompareValidator control in ASP.NET allows you to compare the value of an input control (such as a password textbox) with another value or control. In this case, it can be used to compare two password fields to ensure that they match. By setting the ControlToCompare property of the CompareValidator to the ID of the second password input control and the Operator property to "Equal", the CompareValidator will validate that the values of the two password fields are the same. If the passwords do not match, the validation will fail and an appropriate error message can be displayed to the user. Using the CompareValidator control provides a convenient and reliable way to enforce password matching in web forms, helping to ensure data consistency and accuracy.

To learn more about validation

https://brainly.com/question/30654475

#SPJ11

The process you are describing is called Stereolithography (SLA), which is a type of 3D printing technology that uses a laser to solidify liquid resin layer by layer, creating a solid object.

In this process, a vat of liquid resin is used as the printing material. The printer's build platform is lowered into the resin, and a laser beam is used to selectively draw the shape of the object onto the surface of the resin. The laser causes a chemical reaction in the resin, which hardens and solidifies the material in the desired pattern.

Once a layer is complete, the build platform is raised slightly, and the next layer is drawn on top of the previous one. This process is repeated layer by layer until the entire object is complete.

SLA 3D printing is known for producing high-resolution, detailed objects with smooth surfaces and intricate features. This technology is commonly used in fields such as product design, prototyping, and engineering, where accuracy and precision are critical.

Learn more about build platform: https://brainly.com/question/29591070

#SPJ11

If one loop is tilted slightly relative to the other and their currents are in the same direction, the torques they exert on each other will be in opposite directions.

This can be understood using the right-hand rule for the magnetic field around a current-carrying wire.Consider Loop A and Loop B. If Loop A is tilted slightly relative to Loop B and their currents are in the same direction, the magnetic field produced by Loop A at the location of Loop B will be perpendicular to the plane of Loop B. Similarly, the magnetic field produced by Loop B at the location of Loop A will be perpendicular to the plane of Loop A.

According to the right-hand rule, the torque exerted on a loop in a magnetic field is in a direction perpendicular to both the current direction and the magnetic field direction. Since the currents in both loops are in the same direction, the torques they exert on each other will be in opposite directions, trying to align the loops or counteract the tilting.

Learn more about torques here

https://brainly.com/question/17512177

#SPJ11

In a linked implementation of a dictionary where entries are represented as a chain of nodes that each reference an entry object, you will use 2 pointers per entry. So, the correct answer is option (b) 2.

In a linked implementation of a dictionary, each entry is represented as a node that references an entry object. This implementation is commonly used for dictionaries that require dynamic allocation of memory and efficient insertion and deletion operations. To represent each entry as a chain of nodes, we need to use two pointers per node. One pointer will reference the entry object, while the other pointer will reference the next node in the chain. Therefore, we will use two pointers per entry in this implementation. In conclusion, the answer to the question "In a linked implementation of a dictionary, if you represent the entries as a chain of nodes that each reference an entry object, how many pointers will you use per entry?" is (b) 2.

To learn more about dictionary, visit:

https://brainly.com/question/30761830

#SPJ11

Luis is referred to as the team coordinator or team facilitator. He plays a key role in coordinating the work of the team members and resolving conflicts that may arise.

As the go-to person, Luis ensures smooth communication, collaboration, and effective teamwork within the group. He helps to organize tasks, manage timelines, facilitate meetings, and promote a positive team dynamic. The team coordinator acts as a central point of contact for team members, providing support and guidance to ensure the team's success and productivity.

A facilitator is an individual who guides and supports a group of people in achieving a specific goal or outcome. The role of a facilitator is to create an environment that encourages collaboration, open communication, and effective problem-solving within the group. They help to structure and facilitate meetings, workshops, or discussions to ensure that all participants are engaged, their voices are heard, and decisions are made collectively.

To learn more about facilitator
https://brainly.com/question/18220461
#SPJ11

A UDP header consists of 8 bytes, excluding the IP pseudoheader.

The User Datagram Protocol (UDP) header is composed of 8 bytes, not counting the IP pseudoheader. UDP is a connectionless protocol that provides a lightweight and fast communication option in computer networks.

The UDP header contains crucial information for the delivery of data packets, including the source and destination port numbers, the length of the UDP datagram, and a checksum for error detection. By excluding the IP pseudoheader, which is used for the calculation of the checksum, the UDP header itself is fixed at 8 bytes.

Learn more about User Datagram Protocol

brainly.com/question/31113976

#SPJ11

The reasons why an originally round specimen in a ring-compression test may become oval after it is upset are

Ring-compression test evaluates material ductility and deformation under compression.

Plastic deformation is the permanent shape change after stress surpasses elastic limit. Compression forces yield and reshape specimen. Anisotropy is a directional dependence of material properties. Some materials have directional variations in their mechanical properties.

Learn more about  ring-compression test from

https://brainly.com/question/13274092

#SPJ4

According to the question, The depositional feature produced by longshore transport is a spit.

Longshore transport is the process of sediment movement along the shoreline caused by waves approaching the coast at an angle. As waves break and approach the shore, they carry sediment along the coast in a zigzag pattern. This process gradually transports sediment along the shoreline, resulting in the formation of a spit. A spit is a narrow, elongated ridge or bar of sediment that extends from the coastline into the sea. It is typically composed of sand or gravel and is formed as sediment is deposited by wave action and longshore drift. Spits often curve or hook at their seaward end due to changes in wave direction or other coastal processes.

To learn more about depositional feature

https://brainly.com/question/31789715

#SPJ11

Answer:

brake drums or rotors

Explanation:

When the brake pedal is pressed, hydraulic pressure is applied to the brake system which in turn forces the brake shoes to press against the drum or rotor, slowing down or stopping the car.

Brake shoes are a type of braking system used in some older vehicles and heavy-duty applications. They are typically made of metal and lined with friction material, such as asbestos or ceramic, which provides the necessary stopping force. Brake shoes stop a car by exerting pressure on the brake drum or rotor, which is located behind the wheel and rotates with the wheel. When the driver applies the brake pedal, the brake shoes are pushed against the drum or rotor, creating friction and slowing down the wheel. This slows down the car as a whole, allowing it to come to a stop. Proper maintenance and regular replacement of brake shoes are crucial for safe and reliable braking performance.

Learn more about Brakes at:

https://brainly.com/question/14318250

#SPJ11

The statement is true. Self-locking nuts should be used with bolts or screws on turbine engine airplanes in locations where there is a risk of loose components falling or being drawn into the engine air intake scoop.

Turbine engine airplanes operate in high-speed and high-temperature environments, and any foreign object entering the engine can cause severe damage or failure. Engineering a Self-locking nuts are designed with special features that prevent them from loosening under vibration or other forces.

These nuts have a built-in locking mechanism, such as nylon inserts, prevailing torque features, or deformed threads, that provide resistance to loosening. By using self-locking nuts, the chances of nuts, bolts, washers, or screws becoming loose and entering the engine air intake scoop are significantly reduced, ensuring the safety and proper operation of the turbine engine airplane.

To learn more about Engineering  click here

brainly.com/question/31140236

#SPJ11

To design a circuit using a 741 Op-Amp to amplify the difference between two inputs by 2.5, we can follow these steps for both the single op amp and two op amp configurations:

(a) Single Op Amp Configuration:

Connect the inverting terminal (pin 2) of the Op-Amp to one of the input sources.Connect the non-inverting terminal (pin 3) of the Op-Amp to the other input source.Connect a feedback resistor (Rf) between the output (pin 6) and the inverting terminal (pin 2).Connect a resistor (R1) between the inverting terminal (pin 2) and the ground (0V).Connect a resistor (R2) between the non-inverting terminal (pin 3) and the ground (0V).

The values of Rf, R1, and R2 can be calculated using the formula: Rf = R1 * (1 + 2.5)

(b) Two Op Amp Configuration:

Use the same connections as in the single op amp configuration for one of the Op-Amps.Use the other Op-Amp as an inverting amplifier with a gain of 2.5.Connect the inverting terminal (pin 2) to the output of the first Op-Amp.Connect a feedback resistor (Rf) between the output (pin 6) and the inverting terminal (pin 2).Connect a resistor (R1) between the inverting terminal (pin 2) and the ground (0V).The values of Rf and R1 in the second Op-Amp configuration can be calculated using the formula: Rf = R1 * 2.5

In both configurations, ensure that the power supply connections (Vcc+ and Vcc-) are properly connected to the Op-Amp. Additionally, choose resistor values based on the desired gain and the available resistor values in the market.

Learn more about amplify here

https://brainly.com/question/31874644

#SPJ11

The range of codes that report pathology and laboratory services are B codes.

In the Current Procedural Terminology (CPT) coding system, pathology and laboratory services are reported using codes in the 80000-89999 range, which are referred to as "laboratory codes." These codes are divided into several subsections based on the type of service being provided, such as microbiology, chemistry, or hematology.

In contrast, A codes are a subset of the International Classification of Diseases, Tenth Revision, Clinical Modification (ICD-10-CM) coding system, and are used to report a variety of healthcare services, including preventive services, diagnostic tests, and medical procedures. A codes do not specifically pertain to pathology and laboratory services, but can be used to report a wide range of services across multiple medical specialties.

Visit here to learn more about pathology brainly.com/question/574840
#SPJ11

Here's a recursive Python function called compute_power that calculates the power of a base number:

def compute_power(base, power):

   if power == 0:

       return 1

   elif power < 0:

       return 1 / compute_power(base, -power)

   else:

       return base * compute_power(base, power - 1)

The function takes two arguments: base is the base number, and power is the exponent to which the base number is raised.

The function uses recursion to calculate the power by multiplying the base with compute_power(base, power - 1) until the power becomes 0. If the power is negative, it calculates the reciprocal of the positive power.

Here's an example of how you can use the compute_power function:

print(compute_power(2, 3))  # Output: 8

print(compute_power(5, 0))  # Output: 1

print(compute_power(10, -2))  # Output: 0.01

In the above example, compute_power(2, 3) calculates 2 raised to the power of 3, which is 8. compute_power(5, 0) returns 1, as any number raised to the power of 0 is 1. compute_power(10, -2) calculates the reciprocal of 10 squared, resulting in 0.01.

Learn more about Python here

https://brainly.com/question/26497128

#SPJ11

a. The equal-frequency partitioning for the given sales price records would be as follows: Bin 1: 5, 10, 11, 13  Bin 2: 15, 35, 50, 55  Bin 3: 72, 92, 204, 215

(a) Equal-Frequency (Equidepth) Partitioning:

Equal-frequency partitioning divides the data into bins of equal frequency. In this case, we have 12 records, so we need to partition them into three bins.

Now, we can assign the records to the bins based on their order. Starting from the lowest value, we assign four records to each bin until all records are assigned. If there are any remaining records, we distribute them evenly across the bins.

Using this method, the equal-frequency partitioning for the given sales price records would be as follows:

Bin 1: 5, 10, 11, 13

Bin 2: 15, 35, 50, 55

Bin 3: 72, 92, 204, 215

(b) Equal-Width Partitioning:

Equal-width partitioning divides the data into bins of equal width or range. In this case, we need to determine the range of the data and then divide it into three equal-width bins.

The range of the data is the difference between the maximum and minimum values, which is 215 - 5 = 210.

Each bin will have a width of 210 / 3 = 70. Starting from the minimum value, we assign the records to the bins based on their value falling within the corresponding width range.

Using this method, the equal-width partitioning for the given sales price records would be as follows:

Bin 1: 5, 10, 11, 13, 15, 35

Bin 2: 50, 55, 72, 92

Bin 3: 204, 215

Learn more about price on

https://brainly.com/question/1153322

#SPJ1

The given statement "as the resistor is charged, an impressed voltage is developed across its plates as an electrostatic charge is built up" is true because  when charges flow through the resistor, they encounter resistance, leading to the generation of heat.

When a resistor is charged, an electrostatic charge accumulates across its plates, leading to the development of an impressed voltage. This phenomenon occurs due to the movement of electric charges within the resistor.

As charges flow through the resistor, they encounter resistance, which generates heat and causes an accumulation of charge. This buildup of charge creates a potential difference or voltage across the plates of the resistor.

Learn more about Electrostatic charge

brainly.com/question/30574738

#SPJ11

To simplify the given boolean expression f(a, b, c) = (ab'c)', we can apply De Morgan's theorems and other boolean algebra rules.

First, let's apply De Morgan's theorem to the inner expression (ab'c):

(ab'c)' = a' + b + c'

Next, let's apply De Morgan's theorem to the entire expression (a' + b + c'):

f(a, b, c) = (a' + b + c')'

Using De Morgan's theorem again, we can distribute the negation across the terms:

f(a, b, c) = (a')' · (b)' · (c)'

Now, we can simplify further:

(a')' = a

(b)' = b

(c)' = c

Therefore, the simplified expression is:

f(a, b, c) = a · b · c

So, the minimum (simplest) expression for f(a, b, c) is a · b · c.

Learn more about boolean here

https://brainly.com/question/28706924

#SPJ11

To calculate the mass flux density of the pollutant through the tube due to advection, we can use the formula:

Mass flux density = Concentration × Flow rate

Given: Flow rate of water = 100 cm^3/s

Pollutant concentration in water = 2 mg/L

(a) Mass flux density of the pollutant through the tube due to advection:

Mass flux density = 2 mg/L × 100 cm^3/s

To simplify the units, we need to convert cm^3 to liters:

1 cm^3 = 0.001 L

Mass flux density = 2 mg/L × 100 × 0.001 L/s

Mass flux density = 0.2 mg/s

(b) The total mass flux through the tube due to advection can be calculated by multiplying the mass flux density by the cross-sectional area of the tube.

Assuming the tube has a constant cross-sectional area, we would need the dimensions of the tube to calculate it. Without that information, we cannot determine the exact value of the total mass flux.

Learn more about pollutant here

https://brainly.com/question/19621497

#SPJ11

To determine the complex power, we need to use the formula:

S = P + jQ

Where S is the complex power, P is the real power, Q is the reactive power, and j represents the imaginary unit.

Given that the apparent power S is 600 VA and the reactive power Q is 475 VAR (inductive), we can substitute these values into the formula to find the complex power.

S = P + jQ

600 VA = P + j(475 VAR)

Since the apparent power S is given in VA (volt-amperes) and the reactive power Q is given in VAR (volt-amperes reactive), the complex power will also be expressed in VA.

Therefore, the complex power is 600 + j475 VA.

Learn more about imaginary here

https://brainly.com/question/28286650

#SPJ11

A transformer is a device that transfers electrical energy between two coils.

Transformers consist of two coils, called the primary and secondary coils, wound around a common iron core. When an alternating current (AC) passes through the primary coil, it generates a changing magnetic field in the iron core.

This changing magnetic field induces a voltage in the secondary coil, allowing the transfer of electrical energy from the primary coil to the secondary coil. The ratio of the number of turns in the primary and secondary coils determines the voltage transformation of the transformer.

Learn more about Transformers

brainly.com/question/15200241

#SPJ11

Yes, SQL statements have the ability to change the contents of a database.

The four most commonly used SQL statements that can change the contents of a database are SELECT, INSERT, DELETE, and UPDATE.
The SELECT statement retrieves data from one or more tables in the database. It allows you to specify the columns you want to retrieve, the table or tables you want to retrieve them from, and any filters or sorting you want to apply to the data.
The INSERT statement adds one or more rows to a table in the database. It allows you to specify the values for each column in the row or rows you are adding.
The DELETE statement removes one or more rows from a table in the database. It allows you to specify the conditions that determine which rows to delete.
The UPDATE statement modifies one or more rows in a table in the database. It allows you to specify the new values for each column in the row or rows you are updating, as well as the conditions that determine which rows to update.
As for interfaces, the following are all interfaces: Connection, Driver, ResultSet, and Statement.
A database interface is a layer of software that sits between an application and a database. It provides a set of functions or methods that the application can use to interact with the database.

Learn more about SQL :

https://brainly.com/question/31663284

#SPJ11

This confirms that the triangles are similar. △PQR ~ △STU by SAS similarity theorem (Option B).

T o verify that the triangles are similar, we need to check if the ratios of corresponding sides are equal. Let's analyze the given statements:
StartFraction QR Over TU EndFraction = A.1/4 B.1/2 C.2 D.4
StartFraction PR Over SU EndFraction = A.1/2 B.2 C.4 D.6
StartFraction PQ Over ST EndFraction = StartFraction StartRoot 52 EndRoot Over StartRoot 13 EndRoot EndFraction = A.1/2 B.2 C.4 D.6
By comparing the ratios of corresponding sides:
QR/TU = 1/4
PR/SU = 1/2
PQ/ST = √52/√13 = 2
We can see that the ratios in statement 3 are equal to the corresponding ratios in statement 2 when simplified. This confirms that the triangles are similar.
Therefore, △PQR ~ △STU by SAS similarity theorem (Option B).

To learn more about theorem
https://brainly.com/question/28007778
#SPJ11

The metals typically have the largest values of the coefficient of thermal expansion. The Option A/.

The coefficient of thermal expansion refers to the measure of how much a material expands or contracts in response to changes in temperature. Among the given options, metals generally have the largest values of the coefficient of thermal expansion.

This is because metals have a crystalline structure with closely packed atoms that can easily move and vibrate when exposed to heat leading to significant expansion. Ceramics and polymers tend to have lower coefficients of thermal expansion compared to metals.

Read more about thermal expansion

brainly.com/question/15320204

#SPJ4

A piston, connecting rod, crankshaft, valves, valve plate, head, shaft seal, internal motor overload device, pilot duty motor overload device, and coupling are parts that may be found in a reciprocating compressor.

In a reciprocating compressor, the piston compresses the gas by moving back and forth inside a cylinder. The connecting rod connects the piston to the crankshaft, which converts the linear motion of the piston into rotary motion. The valves regulate the flow of gas into and out of the cylinder, and the valve plate ensures proper sealing. The head contains the valves and is mounted on top of the cylinder, while the shaft seal prevents gas leakage from the compressor. The overload devices protect the motor from damage in case of an overload or overheat. The coupling connects the motor to the compressor.

Learn more about Compressor at:

https://brainly.com/question/7602497

#SPJ11

The correct options are Orders for new merchandise, Customer preferences and requests and Shipping dates

The flow of information between buyer and manufacturer (flow 3) usually communicates the following:
Orders for new merchandise: Buyers communicate their orders for new products or merchandise they wish to purchase from the manufacturer.
Customer preferences and requests: Buyers convey information about customer preferences, specific requirements, or customization requests for the products they are ordering.
Shipping dates: Buyers may communicate shipping dates or delivery requirements to ensure timely delivery of the ordered merchandise.
Therefore, the correct options are:
Orders for new merchandise
Customer preferences and requests
Shipping dates

To learn more about merchandise
https://brainly.com/question/28630529
#SPJ11

To calculate the NO source strength of the heater in mg/hr, we need to use the formula:Source Strength (mg/hr) = Concentration (ppm) x Room Volume (m^3) x Molecular Weight (g/mol) x Air Density (g/m^3) x Air Exchange Rate (1/hr)

Given:

Concentration = 4.7 ppm

Room Volume = 27 m^3

Molecular Weight of NO (NO2) = 46 g/mol (approximate)

Air Density at 25°C and 1 atm = 1.184 g/m^3 (approximate)

Air Exchange Rate = 0.39 1/hr

Substituting the values into the formula:

Source Strength = 4.7 ppm x 27 m^3 x 46 g/mol x 1.184 g/m^3 x 0.39 1/hr

Calculating the result:

Source Strength ≈ 978.6 mg/hr

Therefore, the NO source strength of the kerosene heater is approximately 978.6 mg/hr.

Learn more about Source here

https://brainly.com/question/4231278

#SPJ11

To determine the correct RPM (spindle speed) settings for each drill size, we can use the formula N ≈ 4V/D, where N is the spindle speed in RPM, V is the cutting speed in SFM (feet per minute), and D is the diameter of the drill in inches.

Given that the cutting speed (V) is 90 SFM for all drill sizes, we can calculate the RPM settings for each drill size as follows:

1/4-inch diameter drill:

N ≈ (4 * 90) / 0.25 ≈ 360 / 0.25 ≈ 1440 RPM

1/2-inch diameter drill:

N ≈ (4 * 90) / 0.5 ≈ 360 / 0.5 ≈ 720 RPM

1 1/2-inch diameter drill:

N ≈ (4 * 90) / 1.5 ≈ 360 / 1.5 ≈ 240 RPM

Therefore, the correct RPM settings for each drill size are as follows:

1/4-inch diameter drill: 1440 RPM

1/2-inch diameter drill: 720 RPM

1 1/2-inch diameter drill: 240 RPM

These RPM settings ensure the appropriate cutting speed for drilling operations in steel with the given drill sizes.

Learn more about RPM here

https://brainly.com/question/30459970

#SPJ11

The die opening should be around 4.4mm to 4.8mm in diameter. A cutting force of 625,000 N is required to cut the part from the 4-mm-thick stainless steel material using the blanking die.

To determine the dimensions of the blanking punch and the die opening, we need to consider the thickness of the material, which is 4-mm-thick stainless steel (half hard). The dimensions of the blanking punch should be slightly larger than the part outline to ensure that it cuts cleanly through the material. Based on the thickness of the material, a clearance of 10-20% of the material thickness is recommended. Therefore, the die opening should be around 4.4mm to 4.8mm in diameter. For the cutting force required, we need to take into account the yield strength of the stainless steel. The cutting force required is equal to the area of the part outline multiplied by the yield strength of the material. Assuming the part outline is a rectangle, we can calculate the area by multiplying the length and width of the part. Let's assume the length is 50mm and the width is 25mm. Therefore, the area of the part is: 50mm x 25mm = 1250mm²
Assuming the yield strength of the stainless steel is 500 MPa, the cutting force required is: 1250mm² x 500 MPa = 625,000 N
Therefore, a cutting force of 625,000 N is required to cut the part from the 4-mm-thick stainless steel material using the blanking die.

To learn more about diameter

https://brainly.com/question/28446924

#SPJ11