(a) The minimum frequency and the maximum wavelength of the photon required to dissociate the NaCl molecule are 6.432 x 10^14 Hz and 4.66 x 10^-7 m.
(b) The photon is in UV-A region of the electromagnetic spectrum.
(a) The minimum frequency of the photon required to dissociate the NaCl molecule can be calculated using the formula E = hν, where E is the bond energy of NaCl, h is the Planck's constant (6.626 x 10^-34 J s), and ν is the frequency of the photon.
Thus, ν = E/h = 4.26 eV/6.626 x 10^-34 J s = 6.432 x 10^14 Hz.
Using the formula c = λν, where c is the speed of light (3.00 x 10^8 m/s) and λ is the wavelength of the photon, we can calculate the maximum wavelength of the photon required to dissociate the NaCl molecule:
λ = c/ν = 3.00 x 10^8 m/s / 6.432 x 10^14 Hz = 4.66 x 10^-7 m.
(b) The frequency calculated above corresponds to a photon in the ultraviolet (UV) region of the electromagnetic spectrum, which has frequencies ranging from 10^14 Hz to 10^16 Hz and wavelengths ranging from 10 nm to 400 nm.
The maximum wavelength calculated above (4.66 x 10^-7 m) falls within the UV-A region, which has longer wavelengths (315-400 nm) compared to UV-B (280-315 nm) and UV-C (100-280 nm).
for more such question on electromagnetic spectrum
https://brainly.com/question/28035263
#SPJ11
Please answer all questions provided in the picture.
Answer: left Mg 6, right Mg 1
Left P 4, right P 4
Balanced no
Explanation:
b) Given the shapes of the products and the Na-Y cavities, provide an explanation for the product ratio observed upon Na-Y promotion of the reaction versus the unpromoted reaction. Both 2-bromotoluene and 4-bromotoluene can enter and leave the zeolite with approximately equal ability.
The selectivity of a promoted reaction versus an unpromoted reaction can depend on the location, orientation, and shape of the active sites within the zeolite cavities, as well as the size and shape of the reactant molecules.
Figure out Na-Y cavities reaction about 2-bromotoluene and 4-bromotoluene?The shape of the Na-Y zeolite cavities can affect product selectivity.
Na-Y zeolites are characterized by their uniform, microporous structure, which consists of interconnected channels and cages of fixed sizes. These cavities can act as molecular sieves, selectively allowing smaller molecules to pass through while restricting the movement of larger ones. The size and shape of the cavities can determine which molecules can enter and interact with the active sites on the catalyst surface.
In the case of 2-bromotoluene and 4-bromotoluene, since they have similar sizes, they can enter and leave the zeolite with approximately equal ability. However, the location and orientation of the active sites within the cavities can affect the reaction pathway and product selectivity. For example, if the active sites are located in a cavity that is more accessible to 2-bromotoluene than to 4-bromotoluene, then the promoted reaction may favor the production of products that arise from the 2-bromotoluene pathway.
Similarly, if the cavities have different shapes, such as one cavity being more elongated or twisted than the other, the selectivity may be affected by how the reactants and intermediates fit within the cavity. For instance, a more elongated cavity may favor reactions that occur along a linear pathway, whereas a twisted cavity may promote reactions that involve more complex rearrangements.
The selectivity of a promoted reaction versus an unpromoted reaction can depend on the location, orientation, and shape of the active sites within the zeolite cavities, as well as the size and shape of the reactant molecules.
Learn more about Na-Y cavities reaction
brainly.com/question/24240768
#SPJ11
A galvanic anode that would NOT be used to provide CP to steel is:
A Magnesium
B Aluminum
C Zinc
D Chromium
A galvanic anode that would NOT be used to provide CP to steel is:.D) Chromium is not commonly used as a galvanic anode for the cathodic protection (CP) of steel. Magnesium, aluminum, and zinc are commonly used galvanic anodes for the CP of steel.
A galvanic anode is a type of sacrificial anode that is used to protect metal structures from corrosion. It is made from a more active metal than the metal being protected, such as zinc, aluminum, or magnesium. When the anode is electrically connected to the metal being protected and immersed in an electrolyte, such as seawater, a galvanic cell is created. This results in the anode corroding instead of the protected metal. As the anode corrodes, it releases electrons that flow through the electrolyte to the metal being protected, preventing it from corroding. Galvanic anodes are commonly used in pipelines, ships, and offshore structures to prevent corrosion.
Galvanic anodes are commonly used as a form of cathodic protection (CP) to protect metallic structures from corrosion. The anode material is more reactive than the metal being protected, and when connected to the structure through a conductive medium, it corrodes preferentially to the protected metal, thereby providing CP.
Magnesium, aluminum, and zinc are all commonly used as galvanic anodes for CP because they are more reactive than steel and corrode preferentially to it. However, chromium is not typically used as a galvanic anode for CP because it is less reactive than steel and would not provide sufficient protection. Instead, chromium is often used as a passive protective coating on steel, as it forms a thin, stable oxide layer that helps to prevent corrosion.
Know more about the galvanic anode
https://brainly.com/question/31563784
#SPJ11
Vinegars can be 5-20% acetic acid solutions and has been used for medicinal purposes for thousands of years. If a person takes 30 mL of vinegar a day and the molarity of the vinegar is 0. 84 M, then how many grams of acetic acid (HC2H3O2) will be consumed?
The person consuming 30 mL of 0.84 M vinegar will consume 1.51 grams of acetic acid ([tex]HC_2H_3O_2[/tex]) per day.
The molecular weight of acetic acid is 60.05 g/mol.
30 mL = 0.03 L
Now we can use the formula:
moles = molarity × volume
moles of [tex]HC_2H_3O_2[/tex] = 0.84 M × 0.03 L = 0.0252 moles
Finally, we can use the formula:
grams = moles × molecular weight
grams of [tex]HC_2H_3O_2[/tex]= 0.0252 moles × 60.05 g/mol = 1.51 g
Molecular weight, also known as molecular mass, is a fundamental concept in chemistry that refers to the mass of a molecule. It is defined as the sum of the atomic weights of all atoms in a molecule. The unit of molecular weight is atomic mass units (amu) or daltons (Da).
The molecular weight of a compound is crucial in various chemical applications, such as determining the stoichiometry of chemical reactions, calculating the amount of substance required to achieve a certain concentration, and predicting the physical properties of a substance. Additionally, it is a necessary parameter in the determination of the molar mass, which is the mass of one mole of a substance.
To learn more about Molecular weight visit here:
brainly.com/question/27988184
#SPJ4
19) While watching the news one night, you see a commercial for a new vehicle that will be powered
by water. This will be accomplished by passing electricity through water, producing pure oxygen
and pure hydrogen. These two gases will then be mixed together and ignited. This process of
passing electricity through a substance to separate molecules is called
A) electrochemistry
C) electrolysis
B) electrorefining
D) electroplating
The process of passing electricity through a substance to separate molecules is called electrolysis. Option C is correct.
Electrolysis is a process in which an electric current is passed through a conducting medium (such as a liquid or a molten electrolyte) in order to bring about a chemical change. It involves the use of electrical energy to drive a non-spontaneous redox reaction, causing the decomposition or transformation of substances at the electrodes.
Electrolysis has a wide range of applications in various industries. For example, it is used in the extraction of metals from their ores, such as the production of aluminum from bauxite, or the extraction of copper from copper ores.
Electrolysis plays a crucial role in many technological advancements and industrial processes, making it an important area of study in the field of electrochemistry. It has widespread applications in fields such as metallurgy, chemical industry, energy production, and environmental remediation.
Hence, C. is the correct option.
To know more about Electrolysis here
https://brainly.com/question/12994141
#SPJ1
PART OF WRITTEN EXAMINATION:
One method to reduce IR drops through the electrolyte
A) monthly checkups
B) place a reference electrode near the structure
C) galanavic anodes
D) change different types of reference electrodes frequently
The best method to reduce IR drops through the electrolyte is by using galvanic anodes. IR drops refer to the potential drop that occurs within the electrolyte solution due to its resistance.
This drop can significantly affect the performance of the structure, leading to corrosion and reduced efficiency. Galvanic anodes work by generating an electrical current that counteracts the potential drop and prevents corrosion. The anodes are made of a metal with a more negative potential than the metal they are protecting, which results in the anode corroding instead of the structure. This type of protection is commonly used in cathodic protection systems, which are designed to mitigate the effects of corrosion. Other methods such as monthly checkups or changing reference electrodes frequently do not address the root cause of the IR drops and may not provide adequate protection. Therefore, galvanic anodes are the most effective solution for reducing IR drops through the electrolyte.
learn more about the electrolyte Refer: https://brainly.com/question/28699046
#SPJ11
Draw diagrams to show various orientations in which a p orbital and a d orbital on adjacent atoms may form bonding and antibonding molecular orbitals.
In molecular orbital theory, atomic orbitals from adjacent atoms can overlap to form bonding or antibonding molecular orbitals.
Here, we will examine the orientations of p and d orbitals that can result in these types of orbitals.
When a p orbital (lobed shape) overlaps with a d orbital (cloverleaf shape), there are various ways they can align to form bonding and antibonding molecular orbitals. Bonding molecular orbitals result from constructive interference between the wave functions of the atomic orbitals, leading to increased electron density between the nuclei. Antibonding molecular orbitals, on the other hand, arise from destructive interference, creating a node or region of zero electron density between the nuclei.
1. Bonding orientation: A p orbital can overlap with a d orbital when their lobes are parallel and adjacent to each other, like px with dxz. The electron density accumulates between the nuclei, creating a bonding interaction.
2. Antibonding orientation: A p orbital can form an antibonding molecular orbital with a d orbital when their lobes are oriented in such a way that the positive phase of one orbital overlaps with the negative phase of the other, like px with dyz. This leads to destructive interference, and a node forms between the nuclei.
3. Non-bonding orientation: In some cases, there may be no significant overlap between the p and d orbitals, resulting in a non-bonding interaction. For example, a pz orbital may not interact significantly with a dxy orbital due to their orthogonal orientation.
To better visualize these interactions, it is helpful to draw diagrams showing the overlap of the orbitals and the resulting electron density distribution for bonding, antibonding, and non-bonding cases.
To know more about molecular orbital theory, refer to the link below:
https://brainly.com/question/29642622#
#SPJ11
An unknown solution is determined to have a pH of 4.5. Identify the solution as being acidic, basic, or neutral.O acidicO basicO neutralO none of the above
The solution with a pH of 4.5 is acidic. pH is a measure of the concentration of hydrogen ions in a solution.
A pH value below 7 indicates an acidic solution, a pH value of 7 indicates a neutral solution, and a pH value above 7 indicates a basic solution. In the case of the unknown solution with a pH of 4.5, the concentration of hydrogen ions is greater than that of hydroxide ions, indicating that it is acidic. Acidic solutions have a higher concentration of hydrogen ions than hydroxide ions, while basic solutions have a higher concentration of hydroxide ions than hydrogen ions. Neutral solutions have an equal concentration of hydrogen and hydroxide ions. Therefore, based on the pH value of 4.5, the unknown solution can be identified as acidic.For more such question on pH
https://brainly.com/question/12609985
#SPJ11
True or false: When ionic bonds form, they produce individual molecules, each of which consists of a fixed number of positive and negative ions.
The given statement " When ionic bonds form, they produce individual molecules, each of which consists of a fixed number of positive and negative ions" is false because they produce a crystal lattice structure, in which each positive ion is surrounded by a fixed number of negative ions, and vice versa.
When ionic bonds form, they produce a crystal lattice structure, in which each positive ion is surrounded by a fixed number of negative ions, and vice versa.
The lattice structure extends indefinitely in all directions, forming a solid compound. Therefore, ionic compounds do not exist as discrete molecules with a fixed number of ions.
For such more question on molecules:
https://brainly.com/question/475709
#SPJ11
Which sequence represents the relationship between temperature and volume as explained by the kinetic-molecular
theory?
higher volume
->>
O higher temperature → more kinetic energy→more space between particles
O higher temperature → less kinetic energy less space between particles higher volume
O higher temperature → more kinetic energy less space between particles → lower volume
O higher temperature →less kinetic energy→more space between particles → lower volume
Mark this and return
Save and Exit
Next
Submit
The sequence that represents the relationship between temperature and volume as explained by the kinetic-molecular theory is higher temperature/ more kinetic energy/ more space between particles/ higher volume
What is kinetic-molecular theory?The kinetic theory of matter can be described as the theory that stressed that all matter is made of small particles and thses particules are seen to be in random motion with some space between them.
It should be noted that the theory help us to know about matters in their differnt forms such as liquid, solid and gas and the relationshipto temperture and parameters.
Learn more about kinetic-molecular theory at:
https://brainly.com/question/1274627
#SPJ1
Answer:
A.
Explanation:
Predict which fatty acid is most likely to be a solid at room temperature. a.CH3(CH2)3=CH(CH2)3COOH b.CH3(CH2)3COOH
c.CH3(CH2)4(CH=CHCH2)2(CH2)6COOH
d.CH3(CH2)14COOH
The fatty acid is most likely to be a solid at room temperature is CH₃(CH₂)₁₄COOH.
Fatty acids are composed of long hydrocarbon chains with a carboxyl group (-COOH) at one end. The physical properties of fatty acids, such as melting point and solubility, are determined by the length of the hydrocarbon chain and the degree of saturation (i.e., the number of double bonds) in the chain.
Saturated fatty acids, which have no double bonds in the hydrocarbon chain, tend to be solids at room temperature because their molecules can pack closely together, allowing for stronger intermolecular forces (such as van der Waals forces) to hold them in a solid state.
Of the given options, (d) CH₃(CH₂)₁₄COOH is a saturated fatty acid with a long, straight hydrocarbon chain consisting of 16 carbon atoms. Therefore, it is most likely to be a solid at room temperature.
Option (a) CH₃(CH2)₃=CH(CH2)₃COOH and (c) CH₃(CH₂)₄(CH=CHCH₂)₂(CH₂)6COOH both have double bonds in their hydrocarbon chains, which introduce kinks in the chain, preventing molecules from packing closely together, and thus are more likely to be liquids at room temperature.
Option (b) CH₃(CH₂)₃COOH is a short-chain fatty acid with only four carbon atoms in the hydrocarbon chain, and so it is more likely to be a liquid at room temperature.
Therefore, the correct answer is (d) CH₃(CH₂)₁₄COOH.
To know more about the fatty acid refer here :
https://brainly.com/question/30712004#
#SPJ11
PART OF WRITTEN EXAMINATION:
In a corrosion cell, electrons flow in the direction of:
A) anode to the cathode through the electroylte
B) anode to the cathode through the metallic path
C) cathode to the anode through the electrolyte
D) cathode to the anode through the metallic path
Corrosion cells are a condition on a metal surface in which a flow of electric current occurs between the metal surface and an electrolyte with which it is in contact sufficient to cause the metal to degrade.
In a corrosion cell, electrons flow from the anode to the cathode through the metallic path. Therefore, the correct answer to the question is
B) anode to the cathode through the metallic path.
In the corrosion cell, metal ions formed from metal oxidation (cations) migrate from the anode to the cathode through the electrolyte. The electrons given off by this oxidation reaction move from the anode to the cathode through the electrical connection.
to know more about Corrosion cells click this link-
brainly.com/question/30800443
#SPJ11
Select the correct form of the zero-order integrated rate law for one reactant. Select all that apply.
a.ln[A]t - ln[A]0 = kt
b.ln[A]0[A]t = kt
c.1[A]t - 1[A]0 = kt
The correct form of the zero-order integrated rate law for one reactant is: c. 1[A]t - 1[A]0 = kt
Here, [A]t represents the concentration of the reactant at time t, [A]0 is the initial concentration of the reactant, and k is the rate constant.
the correct form of the zero-order integrated rate law for one reactant is [A] = -kt + [A0], where [A] is the concentration of the reactant, k is the rate constant, and [A0] is the initial concentration12. This equation describes a linear plot of [A] versus t, with a slope of -k and a y-intercept of [A0]1.
Therefore, out of the options given, only option a. ln[A]t - ln[A]0 = kt is correct. Option b. ln[A]0[A]t = kt and option c. 1[A]t - 1[A]0 = kt are incorrect forms of the zero-order integrated rate law.
to learn more about integrated rate law click here:
brainly.com/question/30379408
#SPJ11
HOCH(aq) + H2O(l) = H3O+ (aq) + OCI (aq) hi- Ki = H, O OCH] HOCH Reaction 2: 2 H2O(l) = H30+ (aq) + OH(aq) K = [H,0"][OH ] Reaction 3: OCI (aq) + H2O(l) 3 HOCl(aq) + OH(aq) K3 =? Based on the equilibrium constants given above, which of the following gives the correct expression for the equilibrium constant for reaction 3?
A. K3= K2/K1
B. K3= K1K2
C. K3= K1/K2
D. K3= 1/K1K2
The correct expression for the equilibrium constant for reaction 3 will be K3= K1/K2. The correct option is C.
The given equations represent the equilibrium constants for three different reactions. The first equation represents the equilibrium constant (Ki) for the reaction between HOCH and water to form H₃O⁺ and OCI. The second equation represents the equilibrium constant (K) for the reaction between two water molecules to form H₃O⁺ and OH⁻. The third equation represents the equilibrium constant (K3) for the reaction between OCI and water to form HOCl and OH⁻.
To determine the expression for K3, we can use the principle of equilibrium constant multiplication. According to this principle, if a reaction can be expressed as the sum of two or more reactions, the equilibrium constant for the overall reaction is equal to the product of the equilibrium constants of the individual reactions.
In this case, we can see that the overall reaction for K3 can be expressed as the sum of reactions 1 and 2, with the H₃O⁺ and OH⁻ ions cancelling out. Therefore, the correct expression for K3 would be:
K3 = (HOCl)(OH⁻) / (OCI)(H₂O)
Using this expression, we can see that the answer is option C, K3 = K1/K2.
To know more about equilibrium constants, refer to the link below:
https://brainly.com/question/31321186#
#SPJ11
Question 25
Marks: 1
A pH between _____ and _____ is optimal PH control for eye irritation, but is not optimal for chlorine effectiveness.
Choose one answer.
a. 7.5 - 7.6
b. 7.0 - 7.1
c. 7.2 -7.3
d. 7.9 - 8.0
A pH between 7.2 and 7.3 (option c) is optimal for eye irritation control, but is not optimal for chlorine effectiveness.
The pH scale measures the acidity or alkalinity of a solution. For swimming pools, a slightly alkaline pH level (between 7.2 and 7.6) is ideal for preventing eye irritation and maintaining the effectiveness of chlorine as a disinfectant. However, a pH between 7.2 and 7.3, while comfortable for the eyes, is not the most effective range for chlorine.
Hence, The optimal pH range for eye irritation control (7.2-7.3) is not the most effective range for chlorine effectiveness in swimming pools.
learn more about pH click here:
https://brainly.com/question/172153
#SPJ11
based of the molar masses of the three posssible products in equations 1-3 and the number of moles of reactant in each case calculate the expected mass
We must first ascertain the molar masses of the three potential products in equations 1-3 in order to compute the predicted mass.
When we have these numbers, we may multiply each molar mass by the number of moles of reactant present in each scenario to determine the predicted mass.
The molar masses of the products may be found by examining the coefficients of the reactants and products in each chemical equation, assuming that we have balanced chemical equations for each reaction.
The molar mass of water (H₂O), for instance, is 18 g/mol (2 hydrogen atoms with a molar mass of 1 g/mol each, plus one oxygen atom with a molecular mass of 16 g/mol), as shown by the equation 1:
2H₂ + O₂ ⇔ 2H₂OW.
The molar masses of the other two products in equations 2 and 3 may also be found in a similar manner. We may multiply each by the number of moles of reactant in each case once we know their molar masses.
For instance, if equation 1 predicts the reaction of 2 moles of hydrogen gas (H₂) to generate 4 moles of water (2 moles of H₂O for each mole of H₂). The estimated mass of 72 grams is obtained by multiplying the molar mass of water (18 g/mol) by the anticipated number of moles (4).
Using the proper molar mass and number of moles of reactant to get the anticipated mass, we can repeat this process for each of the three potential reactions.
Know more about molar mass:
https://brainly.com/question/30640134
#SPJ12
Calculate the mass of magnesium necessary to evolve 80 mL of H2 at STP. Then weigh approximately this quantity of Mg ribbon on the top-loading balance to the nearest mg(±0. 001 g)
The mass ooff magnesium is 0.0371 g, under the condition that to evolve 80 mL of H₂ at STP.
To calculate the mass of magnesium necessary to evolve 80 mL of H₂ at STP, we can use the equation
PV = nRT
Here
P = pressure,
V = volume,
n = number of moles,
R = gas constant,
T = temperature.
At STP, the pressure is 1 atm and the temperature is 273 K. Hence the volume of 80 mL can be converted to 0.08 L.
The number of moles of hydrogen gas produced can be evaluated as
n(H₂H₂2) = (PV) / (RT)
= (1 atm * 0.08 L) / ([tex]0.08206 L atm mol^{-1 }K^{-1} * 273 K[/tex])
= 0.00306 mol
Now, according to the balanced chemical equation for the reaction between magnesium and hydrochloric acid
Mg + 2HCl → MgCl₂ + H₂
One mole of magnesium reacts with two moles of hydrochloric acid to produce one mole of hydrogen gas. Then, we need half as many moles of magnesium as we have moles of hydrogen gas.
n(Mg) = n(H₂) /2
= 0.00306 mol / 2
= 0.00153 mol
The given molar mass of magnesium is approximately 24.31 g/mol.
Finally
mass(Mg) = n(Mg) * M(Mg)
= 0.00153 mol * 24.31 g/mol
≈ 0.0371 g
To learn more about mass
https://brainly.com/question/86444
#SPJ4
Physical, Chemical, or Therapeutic Incompatibility?:
Penicillin is stable for 24 hours in aqueous solution having a pH of 6.5. However, at pH 3.5, it is degraded in less than an hour.
Penicillin is stable for 24 hours in aqueous solution having a pH of 6.5
in this case is chemical Incompatibility given
Penicillin is a drug that is known to be pH sensitive. In this scenario, the stability of penicillin in an aqueous solution is dependent on the pH level of the solution. Penicillin is stable for 24 hours in an aqueous solution with a pH of 6.5, but at a pH of 3.5, it quickly degrades in less than an hour. This means that the chemical makeup of the penicillin is altered at a pH of 3.5, resulting in its degradation
The incompatibility of penicillin is due to its chemical sensitivity to pH. It is important to note that any medication that is pH sensitive must be stored and administered in a manner that ensures the pH level is within the acceptable range to maintain its stability and effectiveness.
To know more about pH visit:
brainly.com/question/28580519
#SPJ11
Which of the following ions could exist as either a low-spin or a high-spin octahedral complex depending on the crystal field splitting of the ligands? A) Mn2* B) Ni2* C) Sc* D) Cu2+ E) Zn*
Ni²⁺ is the only ion on the list that can exist as both a high-spin and a low-spin octahedral complex. So, the correct answer is B. Ni²⁺.
What is crystal field theory?An electrostatic model called the crystal field theory (CFT) assumes that the metal-ligand connection is ionic and results only from electrostatic interactions between the metal ion and the ligand. When dealing with anions, ligands are viewed as point charges, and when dealing with neutral molecules, as dipoles.
The crystal field splitting theory predicts that some transition metal ions can exist as either high-spin or low-spin octahedral complexes, depending on the magnitude of the crystal field splitting parameter (Δ) relative to the pairing energy (P).
Of the ions listed, the only one that could exist as either a high-spin or a low-spin octahedral complex is Ni²⁺ (B).
Mn²⁺ (A) is a d⁵ ion and will always form a high-spin octahedral complex due to its large number of unpaired electrons.
Sc³⁺ (C) is a d⁰ ion and does not form octahedral complexes with ligands.
Cu²⁺ (D) is a d⁹ ion and typically forms a low-spin octahedral complex due to the stability of the half-filled d⁹ configuration.
Zn²⁺ (E) is a d¹⁰ ion and does not have any unpaired electrons to undergo spin pairing, so it will always form a low-spin octahedral complex.
Therefore, the correct answer is B) Ni²⁺.
Learn more about crystal field theory on:
https://brainly.com/question/23840749
#SPJ11
What is the basic subunit of elements?
A) molecules
B) neutrons
C) atoms
D) protons
E) electrons
The basic subunit of elements is atoms. Therefore the correct option is option C.
An atom is the smallest unit of an element that retains the chemical properties of that element. It consists of a nucleus, which contains protons and neutrons, and electrons, which orbit the nucleus. The number of protons in an atom's nucleus determines its atomic number and defines the element to which it belongs.
Molecules, on the other hand, are formed when two or more atoms combine chemically. So while molecules can be made up of atoms, atoms themselves are the basic building blocks of elements. Therefore the correct option is option C.
For such more question on atoms:
https://brainly.com/question/6258301
#SPJ11
The molecular formula of a compound having an empirical formula NH2(â³ = 32.05 g/mol) is N ___ H___ .
The molecular formula of a compound having an empirical formula [tex]NH_2[/tex] (Molecular weight = 32.05 g/mol) could be [tex]N_2H_4[/tex].
To find the molecular formula of a compound with the given empirical formula ([tex]NH_2[/tex]), we will follow these steps:
1. Determine the molar mass of the empirical formula.
2. Divide the given molar mass of the compound by the molar mass of the empirical formula.
3. Multiply the empirical formula by the obtained ratio to get the molecular formula.
Step 1: Calculate the molar mass of the empirical formula [tex]NH_2[/tex]:
N = 14.01 g/mol (nitrogen)
H = 1.01 g/mol (hydrogen)
Molar mass of [tex]NH_2[/tex] = 14.01 + (2 x 1.01) = 16.03 g/mol
Step 2: Divide the given molar mass (32.05 g/mol) by the molar mass of the empirical formula (16.03 g/mol):
32.05 / 16.03 ≈ 2
Step 3: Multiply the empirical formula ([tex]NH_2[/tex]) by the obtained ratio (2) to get the molecular formula:
[tex]N_2H_4[/tex]
To learn more about molecular formula click here https://brainly.com/question/28647690
#SPJ11
Which of the following structural features allow an alcohol to exhibit Intermolecular hydrogen bonding? Select all that apply.Check all that apply.whic XC medi XThe presence of hydrogen atoms bonded to carbonThe polar bond between oxygen and carbonThe presence of nonbonding electron pairs on the oxygen atomA hydrogen atom bonded to a highly electronegative oxygen atom
The structural features that allow an alcohol to exhibit intermolecular hydrogen bonding are:
1. The presence of nonbonding electron pairs on the oxygen atom
2. A hydrogen atom bonded to a highly electronegative oxygen atom.
The polar bond between oxygen and carbon and the presence of hydrogen atoms bonded to carbon are not sufficient to allow intermolecular hydrogen bonding in alcohols.
An example of an intermolecular force known as hydrogen bonding is the attraction of an electronegative atom in one molecule to a hydrogen atom that is bound to a strongly electronegative atom, such as nitrogen, oxygen, or fluorine. Intermolecular hydrogen bonding can take place in alcohols between an oxygen atom's non-bonding electron pairs and the hydrogen atom connected to its electronegative neighbor.
Numerous physical and chemical characteristics of alcohols, including their high boiling temperatures, high viscosities, and water solubility, are caused by this sort of bonding. Intermolecular hydrogen bonding is not possible when there is a polar link between oxygen and carbon or when hydrogen atoms are bound to carbon because those atoms lack the electronegative oxygen or nitrogen needed for this type of bonding are absent.
To know more about the hydrogen bonding refer here :
https://brainly.com/question/10904296#
#SPJ11
in a supersonic ramjet engine air is decelerated (compressed) by an inlet, enters the combustion chamber at very low speed ( ), then it reacts with fuel and is expelled by a nozzle. let us assume all processes are adiabatic, with the exception of the combustion chamber. a) which of the following statements is true? group of answer choices the total enthalpy is constant from the freestream to the exhaust. the enthalpy decreases from the freestream to the combustor entrance. the total enthalpy is constant from the freestream to the combustor entrance. the enthalpy is constant throughout the engine.
The correct answer is: the total enthalpy is constant from the freestream to the combustor entrance.
In a supersonic ramjet engine, air is decelerated and compressed by an inlet before entering the combustion chamber at very low speed. The air then reacts with fuel and is expelled by a nozzle.
If we assume all processes are adiabatic except for the combustion chamber, which of the following statements is true?
The correct answer is: the total enthalpy is constant from the freestream to the combustor entrance.
Enthalpy is a thermodynamic property that represents the total energy of a system, including both its internal energy and the work required to maintain its pressure and volume. In an adiabatic process, where there is no heat transfer, the total enthalpy remains constant.
In the case of a supersonic ramjet engine, the total enthalpy is constant from the freestream to the combustor entrance. This is because the air is compressed by the inlet, which increases its internal energy and enthalpy. As the air enters the combustion chamber, fuel is added and combustion takes place, which further increases the enthalpy of the air-fuel mixture. However, since the combustion chamber is not adiabatic, there is heat transfer from the combustion products to the surroundings, which decreases the enthalpy of the air-fuel mixture. As a result, the total enthalpy of the mixture remains constant from the freestream to the combustor entrance.
After leaving the combustor, the air-fuel mixture expands through a nozzle, which further decreases its enthalpy. However, since the nozzle is also adiabatic, the total enthalpy of the mixture remains constant from the combustor entrance to the exhaust.
for more such questions on compressed
https://brainly.com/question/27096986
#SPJ11
Which of the following chemical reactions represents an acid-base reaction?
1-NH4OH + KCl --> KOH + NH4Cl
2-ZnCl2 + MgSO4 --> ZnSO4 + MgCl2
3-HBr + KOH --> KBr + H2O
4-H2SO4 + CaCl2 --> CaSO4 + HCl
The reaction which represents an acid-base reaction is HBr + KOH → KBr + H₂O. Option 3 is correct.
An acid-base reaction, also known as a chemical reaction or a neutralization reaction, is a type of chemical reaction that involves the transfer of protons (H⁺) between an acid and a base. Acids are the substances which can donate protons, while bases are substances that can accept protons.
In an acid-base reaction, the acid donates a proton (H⁺) to the base, forming water (H₂O) and a salt. The salt is typically formed by the cation of the base combining with the anion of the acid.
For example; HBr + KOH → KBr + H₂O
This chemical equation represents an acid-base reaction between hydrobromic acid (HBr) and potassium hydroxide (KOH). In this reaction, HBr donates a proton (H⁺) to KOH, which acts as a base and accepts the proton to form water (H₂O), while KBr is formed as a salt. This is a classic example of an acid-base reaction, where an acid and a base react to form a salt and water.
Hence, 3. is the correct option.
To know more about acid-base reaction here
https://brainly.com/question/15209937
#SPJ1
select all the approximate bond angles between bonding domains that appear in the following molecular geometry
90° ,109.5°, 120°, 180° are the appropriate bond angles between bonding domains that appear in the following molecular geometry.
In molecular geometry, bond angles refer to the angles formed between bonding domains, which include both bonded atoms and lone pairs of electrons. The following molecular geometries exhibit various approximate bond angles:
1. Linear geometry: This occurs when there are two bonding domains around the central atom, resulting in a 180° bond angle. Examples include CO₂ and BeCl₂.
2. Trigonal planar geometry: With three bonding domains, the bond angles are approximately 120°. Molecules such as BF₃ and SO₃ exhibit this geometry.
3. Tetrahedral geometry: This geometry has four bonding domains, leading to bond angles of approximately 109.5°. CH₄ and NH₃ are examples of molecules with tetrahedral geometry.
4. Trigonal bipyramidal geometry: In this case, there are five bonding domains, resulting in bond angles of 90° and 120°. Examples include PCl₅ and SF₄.
5. Octahedral geometry: With six bonding domains, octahedral molecules have bond angles of 90°. Molecules like SF₆ and Cr(CO)₆ exhibit this geometry.
These bond angles can be affected by the presence of lone pairs, which create deviations from ideal bond angles. For instance, water (H₂O) has two lone pairs and a bent geometry, resulting in a bond angle of approximately 104.5° instead of the expected 109.5° in a perfect tetrahedral arrangement.
Hence, 90° ,109.5°, 120°, 180° are all the approximate bond angles.
To know more about bond angles, refer to the link below:
https://brainly.com/question/13751116#
#SPJ11
Complete Question:
If you know only the following information can you always determine what the element is (yes/no)
Yes for instance.
once given the physical properties of the alkali metal you can be able to indicate the group and where you can find them in the periodic table. properties like it being soft and having relatively low melting point (Li, Na, K, RB, CS, Fr)
or once been said that it reacts with group 7 Elements that means we are quick to know it out of those elements.
now to answer your question specifically, if the information given upon says an element burns in air with a yellow flame. Then we are quick to say it's Sodium.
so yeah.
Two vessels are labeled A and B. Vessel A contains NH3 gas at 87°C, and vessel B contains Ne gas at the same temperature. If the average kinetic energy of NH3 is 7.1 × 10−21 J/molecule at 70°C, calculate the root-mean-square speed of Ne atoms in m/s.
Answer:
The average kinetic energy of a molecule is given by the formula: KE = (3/2)kT
where k is the Boltzmann constant, T is the temperature in kelvin.
To calculate the root-mean-square speed (v_rms) of Ne atoms, we can use the formula: v_rms = √((3kT)/m, where m is the mass of a Ne atom.
First, we need to convert the temperature of NH3 gas to kelvin: T_A = 87°C + 273.15 = 360.15 K
The average kinetic energy of NH3 at this temperature is given as 7.1 × 10−21 J/molecule.
We can rearrange the first formula to solve for k: k = 2/3 * (KE/T)
Substituting the values for KE and T_A, we get:
k_A = 2/3 * (7.1 × 10−21 J/molecule) / 360.15 K
= 3.3 × 10−26 J/K
The mass of a Ne atom is approximately 20 atomic mass units (u) or 3.32 × 10−26 kg.
Substituting the values of k and m into the second formula, we get:
v_rms = √((3kT)/m)
= √((3 * 3.3 × 10−26 J/K * 360.15 K) / (3.32 × 10−26 kg))
= 437.3 m/s (rounded to three significant figures)
Therefore, the root-mean-square speed of Ne atoms in vessel B is approximately 437 m/s at 87°C
Explanation:
If u have further questions, please ask me on sn ap = m_oonlight781for a gas, which two variables are directly proportional to each other (if all other conditions remain constant)? 1. t and n 2. p and n 3. p and t
For a gas, the two variables that are directly proportional to each other (if all other conditions remain constant) are:
Pressure (p) and temperature (t)
This relationship is described by the ideal gas law, which states that the product of pressure and volume is directly proportional to the product of the number of moles and temperature, when other conditions are constant:
pV = nRT
where:
p is the pressure of the gas
V is the volume of the gas
n is the number of moles of the gas
R is the universal gas constant
T is the temperature of the gas in Kelvin
From this equation, we can see that pressure (p) and temperature (T) are directly proportional to each other, when the other variables are held constant. As the temperature of a gas increases, the pressure of the gas will also increase, assuming all other conditions (such as volume and number of moles) remain constant. Similarly, if the temperature of a gas decreases, the pressure of the gas will also decrease.
To know more about the pressure & temperature refer here :
https://brainly.com/question/30313321#
#SPJ11
In what ways is the reaction between calcium and water different than the reactions between sodium and water, and potassium and water?
Calcium on reaction with water form calcium hydroxide which is sparingly soluble whereas the hydroxides of sodium and potassium are soluble in water.
Water reacts with calcium, magnesium, potassium, and sodium to form its hydroxide compounds. The amount of calcium hydroxide in water has changed.
Due to the compound's extremely poor solubility, calcium hydroxide appears opaque. In comparison to other oxides, calcium hydroxide has an extremely low Ksp (solubility product).
Magnesium, potassium, and sodium hydroxides are soluble in water. Therefore, these substances don't cause water to get hazy.
Because phenolphthalein is a basic substance, the solution turns pink when it is added. In a base, phenolphthalein has a pink colour; in an acid, it has no colour.
To know about calcium
https://brainly.com/question/9584549
#SPJ4
Which of the following is the best method for the synthesis of isobutyl bromide from t-butyl chloride?:* A) 1. NaOH 2. HBr B) 1. NaOCH_3 HBr C) 1. H_2SO_4 and heat 2.NBS and hv D) 1. NaOCH_3 2. HBr and ROOR E) 1. NaoH 2. NBS and hv
The best method for the synthesis of isobutyl bromide from t-butyl chloride is a nucleophilic substitution which is option A) 1. NaOH 2. HBr.
This is a nucleophilic substitution reaction, where the hydroxide ion (from NaOH) attacks the t-butyl chloride molecule, resulting in the formation of an intermediate t-butyl hydroxide. This intermediate then reacts with HBr to form isobutyl bromide. This method is effective because it avoids the formation of unwanted side products and is a straightforward two-step process. Option B involves the use of methoxide ion, which is a strong base and can result in elimination reactions. Option C involves the use of strong acid and heat, which can also lead to elimination reactions. Option D involves the use of an organic peroxide (ROOR), which can be dangerous to handle. Option E involves the use of NBS and hv (light), which can lead to the formation of unwanted side products. The correct answer is option A.
More on nucleophilic substitution: https://brainly.com/question/15970188
#SPJ11