In the "free-form" IAM model, the organization's internal network is responsible for maintaining the sources of identity and attributes. True or false?

Stressing jacks and gauges are essential tools in the construction and engineering industry, used for measuring the tension and compression forces in various structures. It is crucial that these instruments are calibrated regularly to ensure that they provide accurate readings.

According to industry standards and regulations, stressing jacks and gauges should be calibrated at intervals not exceeding six months. This is necessary to maintain the accuracy and reliability of the instruments and to ensure that the structures being tested are safe and secure. Calibration involves comparing the readings of the instrument to a known standard to determine its accuracy and to adjust it if necessary.

It is also important to note that the calibration of these instruments should only be carried out by trained and certified professionals who have the necessary knowledge and expertise. Any calibration deviations should be documented, and the instruments should not be used until they are recalibrated and verified to be within acceptable limits.

In summary, regular calibration of stressing jacks and gauges is essential to maintain their accuracy and ensure that the structures being tested are safe and secure. The recommended calibration interval is not exceeding six months, and the calibration should only be performed by trained and certified professionals.\

Learn more about jacks here:

https://brainly.com/question/506622

#SPJ11

Bounce Rate is the website interaction metric that is best at detecting visitors that viewed only a single webpage on their visit. The correct answer is (c).

Bounce rate is defined as the percentage of single-page visits, which means the percentage of visits in which a person left your website from the landing page without browsing any further. Therefore, if a visitor only views one page and then leaves the site, their visit will be counted as a bounce.

Pageviews per visit, exit percentage, and average time on site are not as good at detecting visitors that viewed only a single webpage on their visit.

Pageviews per visit and average time on site may be higher if a visitor views multiple pages, even if they only spend a short amount of time on each page.

Exit percentage measures the percentage of exits from a particular page, but a visitor can exit from any page on the site, not just the first page they viewed.

Learn more about site metric here:

https://brainly.com/question/1837503

#SPJ4

The total stress is given as 44.623

Find the moment at c

= 3 / 5 * 16 - 1.8 * 16 * 16/2

= 24

shear force at A and B

-24 * 3/5 + 1.8 * 11

= 5.4

24 x 4 / 5

= 19.2 Kip

M = 24 * 3/5 * 11 - 1.8 * 11 * 11 / 2

= 49.5 Kip

Find the centroid

The value of the centroid is 5.39 from B and it is 2.11 from point A

Find the moment of In ertia around X axis

This is given as 73.66 in ⁴

Normal stress at A

19.2 / 1 x 6 + 7 x 1.5

= 1.163 ksi

49.5 x 12 x 5.39 / 73.66

= 43.46

The total stress at the point B

= 1.163 ksi +  43.46

= 44.623

The total stress is given as 44.623

Read more on stress loads here:https://brainly.com/question/13323387

#SPJ4

When the CP current is interrupted the difference in potential with current applied and the instant off potential is the C) IR drop.

The IR drop refers to the voltage drop that occurs across a resistor when current is flowing through it, as described by Ohm's Law (V=IR). In this case, when the CP (cathodic protection) current is interrupted, there will be a difference in potential between the applied current and the instant off potential due to the resistance in the circuit, which results in the IR drop. This can affect the effectiveness of cathodic protection systems and must be taken into account during their design and maintenance.

When the cathodic protection current is interrupted, the potential difference between the applied current and the instant off potential can result in a voltage drop across the circuit. This is known as the IR drop, which occurs due to the resistance in the circuit. This can affect the effectiveness of cathodic protection systems, as it can reduce the potential difference between the metal being protected and the cathode, resulting in less protection against corrosion. It is important to consider the IR drop when designing and maintaining cathodic protection systems to ensure their effectiveness.

To know more about cathodic protection visit:

https://brainly.com/question/31557529

#SPJ11

False. Refreshes are quicker. Only the most recently altered data needs to be refreshed.

Reloading or updating what is displayed or stored is referred to as refreshing. If you are on a web page, for example, refreshing the page reveals the most recent content published on that page.

Essentially, you're requesting the site to transfer the most recent version of the page you're viewing to your computer.

It reads the contents of a dynamic memory device and then rewrites it. This is done to ensure that the information in RAM does not vanish.

Learn more about Refresh here:

https://brainly.com/question/30286853

#SPJ4

Based on the information provided, figure 1 appears to depict a hanger casting that is experiencing a tensile load.

This load is applied along the line that connects the centers of the two holes labeled "a" and "b". It is important to note that when a material is subjected to a tensile load, it experiences a force that pulls it apart along the axis of the load. In the case of the hanger casting, this means that the material is being stretched along the line connecting the centers of the holes. Understanding the type of load and direction of force acting on a material is important for determining its strength and ability to withstand such loads.

To learn more about tensile visit;

https://brainly.com/question/14293634

#SPJ11

The reason for the different strength reduction factors for a concrete section controlled by flexure and shear is due to the behavior of the concrete member under these two conditions. When a concrete member is subjected to flexure, the failure occurs primarily due to the yielding of the longitudinal reinforcement.

Hence, a strength reduction factor of 0.9 is sufficient to ensure the safety of the structure as it provides a factor of safety against failure.

On the other hand, when a concrete member is subjected to shear, the failure occurs due to the crushing of concrete before the reinforcement yields. Therefore, the design must include sufficient shear reinforcement to prevent premature failure of the concrete member. The use of stirrups or shear reinforcement is cheaper than the use of longitudinal reinforcement, and hence, a strength reduction factor of 0.75 is appropriate for shear-controlled sections.

In conclusion, the different strength reduction factors for a concrete section controlled by flexure and shear are based on the failure mechanisms of the concrete member. It is essential to consider these factors to ensure the safety and stability of the structure.

Learn more about reduction here:

https://brainly.com/question/14698511

#SPJ11

The new set of stressing equipment should contain documentation and instructions for review prior to being used on-site.

This documentation should include information on the proper use and maintenance of the equipment, as well as any safety guidelines and precautions that need to be taken.

It is important to thoroughly review this information before using the equipment to ensure that it is being used safely and effectively.

Taking the time to properly familiarize oneself with the equipment can also help prevent any potential equipment malfunctions or accidents.

Overall, it is crucial to prioritize safety and carefully follow all instructions when using new equipment on a project.

This ensures the equipment is safe, suitable, and properly calibrated for the project requirements.

Know more about documentation here:

https://brainly.com/question/1218796

#SPJ11

Since the list of Customer Name cannot be shown its can be displayed by the use of SQL query structure.

The query joins three tables (Sales, Customers, and SalesPersons) using SQL's JOIN clause and filters the results using WHERE clauses based on specified criteria. Note that syntax and names may differ based on your database schema. Modify the query to fit your structure.

The inquiry uses SQL's Connect clause to connect the important tables based on their essential and outside keys, and after that employments WHERE clauses to filter the comes about based on the desired criteria, such as the deals date, sales price, and amount sold.

Learn more about SQL query from

https://brainly.com/question/27851066

#SPJ4

A multi-floor collapse in which several floor slabs completely fail and then stack on top of each other is known as a pancake collapse.

A pancake collapse refers to a type of building collapse where multiple floors of a building fail in sequence and stack on top of each other, creating a pile of collapsed floors resembling a stack of pancakes. This type of collapse is typically associated with buildings constructed with lightweight materials, such as concrete slabs, and can be triggered by events such as earthquakes, explosions, or structural failure. The pancake collapse can be particularly devastating as the weight of the collapsed floors can cause further damage to the remaining parts of the building and hinder rescue and recovery efforts.

Learn more about fed's policy here:

https://brainly.com/question/16860555

#SPJ11

The multi-floor collapse in which several floor slabs completely fail and stack on top of each other is known as a pancake collapse.

This type of collapse referred to as a pancake collapse occurs when multiple floor slabs fail simultaneously and collapse resulting in a stack-like formation. This phenomenon is typically associated with structural failures and can have catastrophic consequences.

The stacking of the floor slabs reduces the space between them, making it extremely difficult for anyone trapped within the collapsed structure to survive or be rescued. The pancake collapse is a significant concern in building safety and structural engineering as it highlights the importance of robust design and proper construction techniques.

Read more about pancake collapse

brainly.com/question/541986

#SPJ4

The addition of sodium bicarbonate is usually used to raise the alkalinity. So, the correct answer is option c.

Sodium bicarbonate, also known as baking soda, is commonly used in water treatment processes to increase the alkalinity. Alkalinity refers to the water's ability to neutralize acids and maintain stable pH levels. When sodium bicarbonate is added to water, it reacts with water to form carbonic acid, which then dissociates into bicarbonate ions. These ions increase the water's buffering capacity, meaning it can better resist changes in pH. This is important for maintaining a healthy aquatic environment, as fluctuations in pH can be harmful to aquatic organisms. Therefore, adding sodium bicarbonate helps to stabilize the water's pH by raising the alkalinity (option c).

To know more about the bicarbonate visit:

https://brainly.com/question/4513272

#SPJ11

We can deduce here that the number that follows 777 are:

A. Decimal: The number that follows 777 in decimal counting is 778.

B. Octal: The number that follows 777 in octal counting is 1000.

C. Hexadecimal: The number that follows 777 in hexadecimal counting is 778.

Each digit in a number indicates a multiple of a power of 10, making decimal a base-10 number system used in mathematics and computer science.

Any number can be represented using the 10 digits of the decimal system, which range from 0 to 9.

The decimal system is frequently utilized in daily life for computations, measurement, and counting. It is also the most widely used number system in computers and programming languages, where actual numbers and monetary values are frequently represented by it.

Learn more about decimal on https://brainly.com/question/703656

#SPJ4

Answer: No

Explanation: If you were asking for statistical question

In the construction industry, particularly when working with post-tensioned concrete structures, the engineer of the record plays a critical role in ensuring that all components and systems are properly designed, constructed, and functioning as intended. One aspect of this process involves the handling of tendon tails in an encapsulated system.

After the engineer of record has given approval, tendon tails in an encapsulated system must be cut off. This is an essential step in the post-tensioning process to ensure structural stability, maintain proper functioning, and prevent potential issues down the line. Cutting the tendon tails helps reduce stress concentrations, mitigates the risk of corrosion, and ensures a smooth and flush surface on the concrete structure.

During this process, it is crucial to follow the guidelines and recommendations provided by the engineer of record. Their expertise and knowledge of the specific project requirements ensure that the cutting of tendon tails is carried out safely, efficiently, and in accordance with relevant codes and standards.

In summary, cutting off tendon tails in an encapsulated system is a vital step in the post-tensioning process once approval has been granted by the engineer of record. This action contributes to the overall structural stability and longevity of the concrete structure while minimizing potential risks associated with stress concentrations and corrosion.

Learn more about engineer here:

https://brainly.com/question/19117846

#SPJ11

The power required to operate this air-conditioning system is approximately 0.463 kW.

To determine the power required to operate the system, we need to consider the coefficient of performance (COP) of a Carnot heat pump.

The COP is given by the formula:

COP = T_cold / (T_hot - T_cold),

where T_cold is the indoor temperature (297 K) and T_hot is the outdoor temperature (308 K).

COP = 297 / (308 - 297) = 297 / 11 ≈ 27

The power required (P) can be calculated using the formula:

P = Q / COP, where Q is the heat transfer rate in kW.

First, convert the heat transfer rate to kW:

750 kJ/min = 12.5 kW.

P = 12.5 kW / 27 ≈ 0.463 kW

Learn more about the power at

https://brainly.com/question/16906267

#SPJ11

The statement is false, as the term "rem" does consider the biological effect of different kinds of radiation from the same dose in rads.

The term "rem" (Roentgen equivalent in man) does take into consideration the biological effect of different kinds of radiation from the same dose in rads. The rem is a unit of equivalent dose, which accounts for the varying levels of biological damage caused by different types of ionizing radiation. It is calculated by multiplying the absorbed dose in rads by a quality factor specific to the type of radiation in question, thus accounting for their differing biological effects.

To know more about Roentgen equivalent visit:

https://brainly.com/question/31560652

#SPJ11

The max shear stress is given as 10.77 mpa

When force is directed parallel to a plane or surface, the resulting type of stress is known as shear stress. Typically encountered among physics, material science and engineering fields with particular attention paid to fluids, structures, and solids.

Generally, this term defines the ratio between applied force and pertaining area. Shear stress gauges the resistance presented by a fluid (such as viscosity) to flow or its impact upon compression within bodies that are generally solid.

It can be used for deformations created through the application of a specific level of force in materials containing increased solidity.

To calculate the max shear stress:

[tex]\frac{1}{2} \sqrt{400 + 64} \\T_m_a_x= 10.77 mpA[/tex]

Read more about shear stress here:

https://brainly.com/question/20630976

#SPJ4

True. Agglomerative hierarchical clustering procedures are better able to handle outliers than k-means.

Are agglomerative hierarchical clustering procedures better at handling outliers than k-means? (True/False)

1. Agglomerative hierarchical clustering procedures are better able to handle outliers than k-means. [True] - Agglomerative hierarchical clustering is more robust to outliers because it builds clusters by merging them based on proximity, whereas k-means can be influenced by outliers due to the mean calculation.

2. Different runs of k-means can produce different clusterings, but agglomerative hierarchical clustering procedures will always produce the same clustering. [False] - Both k-means and agglomerative hierarchical clustering can produce different clusterings in different runs due to their random initialization or tie-breaking mechanisms.

3. When clustering a dataset using k-means, SSE (Sum of Squared Errors) is guaranteed to monotonically decrease as the number of clusters increases. [False] - Increasing the number of clusters in k-means can sometimes lead to higher SSE values as the algorithm may overfit the data.

4. For a dataset that contains a density-based notion of clusters, a measure of cohesion can show poor values on the true clusters. [True] - Density-based clustering algorithms may struggle to accurately measure cohesion in datasets with irregular cluster shapes or varying densities.

5. The SSE of the k-means clustering algorithm keeps reducing with every iteration. [True] - In each iteration of k-means, the SSE is minimized by updating the cluster centroids and reassigning points, leading to a reduction in SSE.

6. The lowest value of SSE for the k-means algorithm is obtained when k=n, the number of points in the data. [True] - When the number of clusters equals the number of points, each point becomes a separate cluster, resulting in SSE equal to 0.

7. If a cluster is split by picking one of the points as a new centroid and reassigning points to the original or new centroid, the SSE of the clustering would only decrease. [False] - Splitting a cluster can increase the SSE if the new centroid leads to a worse assignment of points, resulting in higher squared errors.

Learn more about hierarchical clustering on:

brainly.com/question/29769638

#SPJ12

answer:

stormwater management system and sanitary sewer system

explanation:

The two main types of gravity pipe systems that can be designed with Civil 3D are:

1) Pressure pipe system - This type of system is used to design and analyze pipes that are under pressure, such as water supply systems. The pipes are designed to withstand the pressure and flow of the fluid being transported.

2) Gravity pipe network - This type of system is used to design and analyze pipes that rely on gravity to transport fluids, such as stormwater drainage systems. The pipes are designed to follow the natural slope of the land and gravity to move the fluid from higher elevations to lower elevations.

Learn more about pipe system: https://brainly.com/question/30365511

#SPJ11

The real length of 1 decametre is 10 meters or 1000 centimeters.

In the drawing, a line of 5 cm represents this length.

To find the RF (Representative Fraction), we can use the formula:

Hazen-Williams Equation:

The Hazen-Williams equation for head loss is given by:

[tex]hL = 10.67 * (L / C^1^.^8^5) * (Q^1^.^8^5 / d^4^.^8^7)[/tex]

where:

hL = head loss (ft)

L = pipe length (380 ft)

C = Hazen-Williams roughness coefficient for commercial steel pipe (around 120)

Q = flow rate (ft³/s)

d = pipe diameter (2 ft)

[tex]hL_fittings = K * (v^2) / (2 * g)[/tex]

where:

v = flow velocity (ft/s)

g = gravitational acceleration (32.2 ft/s²)

The total head provided by the pump (Hp) is given by:

Hp = (P * 550) / (Q * 62.4)

Hp = hL_pipe + hL_fittings

Manning equation

[tex]Q = (1/n) * A * R^(^2^/^3^) * S^(^1^/^2^)[/tex]

where:

Q = flow rate (ft³/s)

n = Manning's roughness coefficient (for steel, n ≈ 0.012)

A = cross-sectional area of the pipe (ft²)

R = hydraulic radius (ft)

S = pipe slope (ft/ft)

Read more on manning equation here:https://brainly.com/question/31412408

#SPJ4

Corresponding to 500 rpm , 67.17 X 106 revolutions equal to 2239 hrs

So with 95% reliability, the bearing does not sustain the load for 10Kh

Given

Axial load, Fa = 3KN

Radial load , Fr = 7KN

Speed = 500 Rpm

d = 65 mm

From SKF Catalogue (corresponding to 65mm dia deep groove ball bearing )

Dynamic load capacity, C = 42905 N

a) Equivalent radial load Fe = Xi V Fr +Yi Fa

From data book

Xi=0.56 , Yi = 1.3, V=1.2 (given)

Fe = 0.56X1.2X7 + 1.3X3 = 8.6 KN = 8600N

b) Rated life in million revolution, L90 = (C/Fe)3 = (42905/8600)3 = 124.17 = 124.17 X 106 revolutions

L95/L90 = (ln (1/R) / ln (1/R90))1/b = (6.85 (ln (1/0.95)(1/1.17) , R90 = 0.9, R = 0.95, b = 1.17 (constant)

L95 = 67.17 X 106 revolutions

Corresponding to 500 rpm , 67.17 X 106 revolutions equals to 2239 hrs

So with 95% reliability, the bearing does not sustain the load for 10Kh

Read more about load here:

https://brainly.com/question/13092760

#SPJ4

The risk assessment plan is given below as follows:

Risk Assessment Plan:

Identify Hazards:

Examining the geography of the site, one will be able to trace any impending physical dangers (e.g. unstable ground, unhidden electrical wiring). Additionally, reviewing the trade-work carried out and its particular risks by those conducting it (e.g. lofty movements, handling of power machines) as well as potential personal hazards related to the plant itself (e.g. inflammable elements, likelihood of explosions) should take place.

Evaluate the Risks:

To deduce the outliers of each uncovered threat (e.g. minor scratching, death) is necessary in order to measure the potency of occurrence (e.g. consistent, irregular, infrequent) for better understanding of the impact it can possibly cause (e.g. money due, legal effects, credibility damage). After taking these into consideration, assign a risk level based on them.

Control and Mitigation Measures:

Designing an agenda that seeks to eradicate or debilitate the detected hazards via putting into action engineering controls (e.g. support rails, anchorage vestments) as well as administrative prerequisites (e.g training agendas, warning signs), not forgetting to grant security equipment (PPE) wherever needed.

Action Plan:

A structured report must be written to make official knowledge of the assessment and control operations gone through. Furthermore, this document must be updated when fresh perils are noticed or at regular times, making sure that all personnel and contractors participating have knowledge about said hazards and safety methods applied along with being tutored on the correct use of said mechanisms.

Read more about risk assessment plan here:

https://brainly.com/question/28271580

#SPJ1

To convert millimeters (mm) to nanometers (nm), we need to multiply by 1,000,000. This is because there are 1,000,000 nanometers in one millimeter. Therefore, the conversion factor is 1 mm = 1,000,000 nm.\

To convert milligrams (mg) to kilograms (kg), we need to divide by 1,000,000. This is because there are 1,000,000 milligrams in one kilogram. Therefore, the conversion factor is 1 mg = 0.000001 kg.To convert kilometers (km) to feet (ft), we need to multiply by 3280.84. This is because there are 3280.84 feet in one kilometer. Therefore, the conversion factor is 1 km = 3280.84 ft.To convert inches (in) to centimeters (cm), we need to multiply by 2.54. This is because there are 2.54 centimeters in one inch. Therefore, the conversion factor is 1 in = 2.54 cm.

To learn more about nanometers click on the link below:

brainly.com/question/30575178

#SPJ11

If a multimeter reads "0.00" while performing a diode check on both sides of the diode, it indicates that the diode is a short circuit. This means that the diode has no resistance and is allowing current to flow in both directions, which is not the intended behavior of a diode.

A diode is a semiconductor device that allows current to flow in only one direction. It has two terminals, namely an anode and a cathode. The anode is the positive terminal, while the cathode is the negative terminal. When a voltage is applied across the diode in the forward direction, it conducts current, and when the voltage is applied in the reverse direction, it blocks the current flow.

A multimeter is an electronic instrument that is used to measure various electrical parameters like voltage, current, and resistance. It can also be used to check the polarity and continuity of a diode. To perform a diode check, the multimeter is set to the diode test mode, and the red probe is connected to the anode, while the black probe is connected to the cathode.

In conclusion, if the multimeter reads "0.00" while performing a diode check on both sides of the diode, it indicates that the diode is a short circuit. In this case, the diode needs to be replaced with a new one to ensure proper functioning of the circuit.

Learn more about multimeter here:

https://brainly.com/question/30809641

#SPJ11

Hello! The prestressing steel in the free length area is protected by a corrosion-resistant covering, typically consisting of a combination of grease, plastic sheathing, and cementitious grout. The primary purpose of this protection is to shield the steel from harmful environmental factors and ensure its durability and long-term performance.

Prestressing steel is a key component of pre-tensioned and post-tensioned concrete structures. It is made from high-strength steel strands or bars that are tensioned before or after the concrete is cast, creating compressive stress in the concrete, which enhances its load-bearing capacity.

Grease serves as a barrier against moisture and air, preventing rust and corrosion on the steel surface. The plastic sheathing is an additional layer of protection that encapsulates the prestressing steel, creating a robust barrier against physical damage and external influences. Lastly, cementitious grout is used to fill the voids around the prestressing steel, providing a solid, durable layer that adheres well to both the plastic sheathing and the surrounding concrete.

In summary, the protection of prestressing steel in the free-length area is essential to maintain the integrity, strength, and performance of pre-tensioned and post-tensioned concrete structures. This protection is achieved through a combination of grease, plastic sheathing, and cementitious grout, which work together to guard against corrosion and damage.

Learn more about prestressing here:

https://brainly.com/question/29308208

#SPJ11

The maximum velocity based on the information given will be 980 feet per second.

Maximum velocity is defined as the greatest speed an entity can possibly reach in a certain system or situation. This maximum rate of motion is dependent upon multiple factors such as the mass, applied force, and resistance encountered by the object, plus even the environment it is traversing.

When considering classical mechanics, the maximum velocity of an article is calculated via the given equation v = √2*E/m, with v representing its velocity, E standing for its energy, and m signifying its mass.

Based on the information, maximum velocity can be found by using TR , TA vs V curve. The intersection point gives Vmax = 980ft/s (approx)

Learn more about velocity on

https://brainly.com/question/30505958

#SPJ4

The most critical section is with the tightest bending moment and it is in section B.

Torque, alternatively referred to as "moment," measures the rotational force exerted by an object around a pivot point. As a vector, this measurement has both magnitude and direction.

Torque value relies on multiple factors including the level of force applied, the distance between the pivot point and where force implants in it, along with the angle formed between the lever arm and imposed force.

Typical torque measurements are given in units, such as newton meters or foot-pounds, which is valuable knowledge utilized across a range of fields; specifically in physics, engineering and mechanics.

Read more about Torque-Moment here:
https://brainly.com/question/31473966
#SPJ4

Yes, in SolidWorks, you can fully define the shape and size of a sketch using only dimensions and geometric relations.

These dimensions and relations allow you to control the exact placement and orientation of each element within the sketch, ensuring that it meets your design requirements. By defining the sketch in this way, you can easily make changes to the design by simply adjusting the dimensions and relations, rather than having to recreate the entire sketch from scratch. This makes SolidWorks a powerful tool for creating precise and accurate 3D models.

To learn more about geometric relations visit;

https://brainly.com/question/15069391

#SPJ11