Answer:
sink
Explanation:
a substance with a higher density than others will sink and vice versa
PLES help me for brainless
Answer:
a 1 doesn't belong
Explanation:
Gas has fast moving molecules.
Liquids have slow moving molecules.
Solids have vibrating molecules.
A trucker is driving from New Jersey to California to make a delivery of couches. He forgets to adjust the pressure of his tires before his trip and end up blowing out two of his tires while driving through Arizona. Whose law does this example depict? What does this law state? Use the law to explain what happened to the tires.
Answer:
Gay-Lussac's law.
Explanation:
According to Gay-Lussac's pressure law, it states that the pressure of a given mass of gas is directly proportional to the absolute temperature of the gas, the assumption that the volume is kept constant.
Hence, the trucker's tires were blown up because they were under high pressure as he drove from New Jersey to California, as a result of this intense pressure the temperature of the air in the tires began to rise and it directly affected the pressure of the gas in the tires' tubes which also increased to a point that they ended up blowing out, obeying Gay-Lussac's law.
example of physical property
Answer:
Color. I thinkkk.
Phyiscal properties are defined as properties that can be measured or observed without changing the chemical nature of the substance.
Some examples of phsyical properties are:
- Color
- Density
- Volume
- Mass
- Boiling or Melting Points
Is this correct?
If the temperature is below the melting point the substance is a solid
If the temperature is above the boiling point the substance is a gas
If the temperature is in between the boiling and melting points the substances a liquid.
If the normal melting point of a substance is below room temperature, the substance is a liquid at room temperature.
If both the normal melting point and the normal boiling point are above room temperature, the substance is a solid.
A skittish squirrel is climbing vertically on a tree. Its
motion is shown on the following graph of vertical
position y vs. time t.
6
5+
3
2+
1
→t(s)
2
3
4
5
6
7
8
9
What is the instantaneous speed of the squirrel at time
t=2 s?
Answer: 1
Explanation:
Answer:
-0.1
Explanation:
hello nice ppl(ɔ◔‿◔)ɔ ♥
Answer:
Hi
Explanation:
How has your brainly experience been so far? Are you liking?
Answer:
Thx you are sooo noice
Explanation:
UwU U3U
widte speed rom me and distance 502
A yacht sailed at a steady speed for 0.5 hours, passing a cruise ship that was traveling at 25
kilometers per hour. During that time, the yacht traveled 50 kilometers. What was the yacht's
speed?
Write your answer as a whole number.
kilometers per hour
Submit
The speed of the yacht : 100 km/h
Further explanationLinear motion consists of 2: constant velocity motion with constant velocity and uniformly accelerated motion with constant acceleration
At constant velocity motion:the speed of vo = v = constant
acceleration = a = 0
Δx = vt or x = xo + vt
An equation of constant velocity motion
[tex]\large {\boxed {\bold {x = v \times \: t}}}[/tex]
x = distance = m
v = speed = m / s
t = time = seconds
A yacht sailed at a steady speed for 0.5 hours, and traveled 50 kilometers
so the velocity/speed:
[tex]\tt v=\dfrac{x}{t}\\\\v=\dfrac{50~km}{0.5~h}=\boxed{\bold{100~km/h}}[/tex]
What information does not need to be included a chemical waste label? Select one: Relative amounts of chemical compounds in the container. The date the waste container was filled completely. A description of the experiment the chemicals were used for. Names of the chemical compounds present in the container.
Answer:
A description of the experiment the chemicals were used for.
Explanation:
A chemical waste label is required to provide information about any hazardous waste present in the container. Some details are mandatory to mention of the chemical waste label to prevent any accident while doing the experiment, that includes:
Chemical compound's name present in the container.Composition and physical state of the waste.Hazardous properties of the waste.The date of manufacturing.Amount of chemical compounds filled in the container.A chemical waste label does not mention or describe the experiment for which the chemicals were used for, scientists, teacher or students should have knowledge of the chemical composition by reading their names and evaluate themselves on which chemical should be used for which experiment.
Hence, the correct answer is "A description of the experiment the chemicals were used for."
The correct answer is A description of the experiment the chemicals were used for.
A chemical waste label must contain all the information about any hazardous waste present in the container. It should clearly indicate the composition of the waste, the date of manufacturing and the amount of chemical compounds filled in the container. A chemical waste label does not need to mention the experiment for which the chemicals were used.
Learn more;
https://brainly.com/question/20368258
The number of shovels and cost per 1000 kg for
Ca(OH)2
Answer:500
Explanation:
Does changing the number of neutrons affect the atomic number?
Answer:
awsdxcvawsd
Explanation:
Answer:If you change the number of neutrons in an atom, you get an isotope of the same element. The addition of a neutron can make an atom radioactive. When you change the number of protons in an atom, you will change the atom from one element to a different element.
Explanation:
CAN SOMEONE PLEASE HELP ME ASAP PLEASEE ANYBODY LITERALLY ANYONE OUT THERE PLEASE
Which subatomic particle can be shared between separate atoms?
Answer:
Electrons
Explanation:
Atoms can combine together and share electrons between them. Atoms that share electrons are linked to each other in a form, called a molecule that is in a lower energy state than either of the separate atoms alone.
Pls Brainliest! It would mean a lot! ;)
Sciences Grad Bosch Law of Conservation of Mass - Assess it
contents
Target: 10/2001
Science and Enging
Achemical reaction takes place in a closed system. The mass of the reactants before the reaction was
55 watte mass of the products of the reaction be according to the law of conservation
Properties of Matter
Answer:
55
Explanation:
According to the law of conservation properties of Matter in a closed system the mass of reactants is equal to the mass of products. Because there is no lose of matter or energy in closed system
In the apple activity you completed which of the following is an example of a constant
Answer: the type of apple because it is an example of a constant
Explanation:
Elena held a rock weighing 1 N in her hand. The rock has no velocity.
KE________?
KE = 0
Further explanationEnergy is the ability to do work
Energy because its motion is expressed as Kinetic energy (KE) which can be formulated as:
[tex]\large{\boxed{\bold{KE=\frac{1}{2}mv^2}}}[/tex]
So for two objects that have the same speed, the greater the mass of the object, the greater the kinetic energy
The stone in hand is in a motionless state (at rest) so that its velocity (v) = 0, so it has no kinetic energy
But this stone can have potential energy that is gained due to its height
Jakasia needed to find the volume of a plastic container in L to see if the 170 L of
solution that she had would fit inside. She knew that one side was 2.5 ft, the
height of the box was 60 cm, and width of the box was 0.8 m. Use dimensional
analysis to determine if Jakasia's solution will fit in the container.
Answer:
The solution will fit into the container.
Explanation:
The following data were obtained from the question'
Volume of solution = 170 L
Length of container (L) = 2.5 ft
Height of container (H) = 60 cm
Width of container (W) = 0.8 m
Volume of container (V) =?
Next, we shall express the length, height and breadth I the same unit of measurement. In this case, we shall all in centimetres (cm).
For the length:
1 ft = 30.48 cm
Therefore,
2.5 ft = 2.5 ft × 30.48 cm / 1 ft
2.5 ft = 76.2 cm
Thus the length is 76.2 cm
For the width:
1 m = 100 cm
Therefore,
0.8 m = 0.8 m × 100 cm / 1 m
0.8 m = 80 cm
Thus, the width of the container is 80 cm.
Next, we shall determine the volume of the container as follow:
ength of container (L) = 76. 2 cm
Height of container (H) = 60 cm
Width of container (W) = 80 cm
Volume of container (V) =?
Volume = length × width × height
Volume = 76.2 × 80 × 60
Volume = 365760 cm³
Finally, we shall convert 365760 cm³ to litre (L). This can be obtained as follow:
1000 cm³ = 1 L
Therefore,
365760 cm³ = 365760 cm³ × 1 L/ 1000 cm³
365760 cm³ = 365.76 L
Therefore, the volume of the container is 365.76 L
Since the volume of the container (i.e 365.76 L) is bigger than the volume of the solution (i.e 170 L), therefore, the solution will fit into the container.
Analyzing a blood sample usually involves which type of separation method?
screening
distillation
centrifugation
filtration
Answer:
the answer is b
Explanation:
i just did quizz
The temperature at which a substance in its solid state melts into the same substance in a liquid is known as
Answer:
0 C
Explanation:
hey guys plz plz plz help me I am struggling I am in middle and struggling to answer this plz help
I have never learned how to calculate the specific heat there is a photo if u know plz answer we have a lot of people trying to figure out how to solve this and know one knows so plz if u know give it your best shot.
thank u I will most definitely appreciate it
and if u answer this correctly I will give 50 point and mark brainliest
of u are just trying to get point u rill be reported
so thanks guys.
Answer:
I've already answered this one for you. Anyway, please let me know if you have any more questions or need help!
Which is the best way to determine if an object is made of pure silver?
O Determine the solubility of the object.
O Test to see if the object is chemically reactive.
Determine the density of the object and compare the known density of pure silver.
O Compare the mass of the silver object to the mass of a piece of pure silver.
Answer:
The correct option is;
Determine the density of the object and compare the known density of pure Silver
Explanation:
The density of the object is found by finding the weight of the object, and then finding the volume (of water) the object displaces when it is immersed (in water)
The density is then fond by dividing the weighed mass by the volume the object displaces when immersed
Compare the result of the measured density with that of pure silver. If the two have density, as well as other similar physical characteristics, then the object is likely to be pure silver.
Quais são os três tipos de tecidos musculares? E)celulas,estriado esqueletico, estriado liso. B)esttiadi esqueletico, liso, estriado cardiaco c)estriado liso, estriado esqueletico, estriado cardíaco. D)liso, celulas, esteiado cardíaco. ESSA PERGUNTA E DE CIENCIAS MAS NAO TEM VIENCIAS ALI PRA ESCOLHER;-;.
Answer:
c)estriado liso, estriado esqueletico, estriado cardíac
Explanation:
Los 3 tipos de tejido muscular filho cardíaco, liso y esquelético.
O músculo esquelético é responsável pelo movimento dos tons e das outras estruturas. La contracción del músculo cardíaco permite que o corazón bombee sangre. Los músculos lisos permitem que os alimentos se muevan a través del tracto digestivo y también ayudan al cuerpo a absorvedor los nutrientes.
Differences in states of matter are determined by
particle type
particle arrangement
particle color
distance between particles
Answer:
particle distance
solids are tightly packed
liquids are a little farther apart
and gases are very far
“Jesus came to serve. How is He calling me to serve?”
Answer:
...
Explanation:
11. How many moles are in 7.14 X 10 35
molecules of 02?
Answer:
The answer is 1.186 × 10¹² molesExplanation:
To find the number of moles in a substance given it's number of entities we use the formula
[tex]n = \frac{N}{L} \\[/tex]
where n is the number of moles
N is the number of entities
L is the Avogadro's constant which is
6.02 × 10²³ entities
From the question
N = 7.14 × 10^35 molecules of O2
We have
[tex]n = \frac{7.14 \times {10}^{35} }{6.02 \times {10}^{23} } \\ [/tex]
We have the final answer as
1.186 × 10¹² molesHope this helps you
When the first periodic table of the elements was published, the elements were arranged by atomic mass. Although
several elements seemed out of order, later discoveries showed the order to be correct.
Which event most likely helped the development of the periodic table?
O Scientists changed the atomic masses to better fit the pattern.
O Scientists refused to consider other ways to organize the elements.
O New technology was developed that modified the masses.
O New information changed the understanding of the atom's structure.
ANSWER ASAP
what does MA 2 means?
Answer:
Master-at-Arms Petty Officer 2nd Class. MA2. Machine Accountant Second Class (Naval Rating) Copyright 1988-2018 AcronymFinder.com, All rights reserved.
Explanation:
Which statement best describes insoluble substances? Insoluble substances remain the same when in water. Insoluble substances become part of the liquid substance. Water does not remain when an insoluble substance is added. Insoluble substances change from solid to liquid states.
Answer:
Insoluble substances remain the same when in water.
Explanation:
When a substance is regarded as insoluble, it means that the substance remains the same in water.
Soluble substances usually form one continuous phase with water when they are added to water (eg when salt is added to water).
However, when camphor is added to water, it does not form a single phase with water. It remains the same in the water and maintains a separate phase from the water. Hence camphor is an insoluble substance.
name the gas evolved when metal carbonates react with acid and state the method
Answer:
the gas evolved is carbon dioxide
Explanation:
for example we can have a look at sodium carbonate reaction with hydrochloric acid
when sodium carbonate reacts with hydrochloric acid, it results in sodium chloride, carbon dioxide and water.
Answer: Carbon dioxide
How is the nuclear structure of an atom similar to the non-nuclear structure?
Answer:
It has shells of protons and neutrons.
Explanation:
The nuclear structure of an atom is similar to the non-nuclear structure because has shells of protons and neutrons.
What is an atom?An atom consists of a central nucleus that is usually surrounded by one or more electrons.
The total number of neutrons plus protons in the same both before and after the nuclear process, although the total number of protons and the total number of neutrons may be different before and after.
Hence, the nuclear structure of an atom is similar to the non-nuclear structure because has shells of protons and neutrons.
Learn more about the atoms here:
https://brainly.com/question/1566330
#SPJ2
NEEEDDDD HELP ASAP PLZ PLZ PLZ PLZ PLZ HELP ME
Answer:
[tex]ns^2[/tex]
Explanation:
How much heat is required to melt 42.0 grams of water at 0*C?
Hurry...
Answer:
Heat required to melt 42 g if ice is 13,860 J
Explanation:
The amount of heat required to melt grams of water at 0°C is given as follows;
The mass of the ice (water), m = 42 g
The latent heat of fusion of ice Δ[tex]H_f[/tex]= 330 J/g
Therefore, heat required to melt 42 grams is given as follows;
Heat required to melt ice = Mass of the ice, m × The specific latent heat of fusion of the ice, Δ[tex]H_f[/tex]
Heat required to melt 42 g if ice = m × Δ[tex]H_f[/tex] = 42 g × 330 J/g = 13,860 J
Heat required to melt 42 g if ice = 13,860 J.