Four compasses are placed around a wire, as shown.

A long wire that is vertical and standing on a steel plate. There are 4 compasses surrounding it and all of the needles are pointing in the same direction, west.

The wire is then connected to a battery so that a current flows down the wire.

How will the compasses point once the current is flowing?

A long wire that is vertical and standing on a steel plate. There are 4 compasses surrounding it and all of the needles are pointing in the same direction, west.
A long wire that is vertical and standing on a steel plate. There are 4 compasses surrounding it and all of the needles are pointing in the same direction, east.
A long wire that is vertical and standing on a steel plate. There are 4 compasses surrounding it and all of the needles are pointing clockwise.
A long wire that is vertical and standing on a steel plate. There are 4 compasses surrounding it and all of the needles are pointing counterclockwise.

Answer:

d. 4 m/s²

Explanation:

pls mrk me brainliest

Overall, the difference between detached and semi-detached binary systems lies in the extent to which the stars interact with each other and exchange mass.

In a detached binary system, the two stars are far enough apart from each other that they do not significantly interact with each other. The stars have their own gravitational fields, which cause them to orbit around the common center of mass, but they do not exchange significant amounts of mass or significantly alter each other's evolution. Detached binary systems are the most common type of binary systems.

In contrast, in a semi-detached binary system, one of the stars is closer to the common center of mass than the other and is therefore more strongly affected by the gravitational pull of the other star. The closer star can transfer mass to the more distant star, often through an accretion disk, causing the more distant star to become more massive and the closer star to become less massive over time. Semi-detached binary systems can lead to various phenomena such as accretion disks, mass transfer, and outbursts of energy.

To know more about binary system,

https://brainly.com/question/13045809

#SPJ1

The correct answer is D. I, II, and III. All three of the variables listed can be affected if a dielectric is inserted into a parallel plate capacitor.

When a dielectric is inserted into a parallel plate capacitor, the capacitance increases. This is because the dielectric reduces the electric field between the plates, which in turn reduces the potential difference between the plates. This allows for more charge to be stored on the plates for a given potential difference, resulting in an increase in capacitance. The electric field between the plates is also affected when a dielectric is inserted into a parallel plate capacitor. The dielectric reduces the electric field between the plates by reducing the potential difference between the plates.

Finally, the electric potential is also affected when a dielectric is inserted into a parallel plate capacitor. The potential difference between the plates is reduced when a dielectric is inserted, which in turn reduces the electric potential. Therefore, all three of the variables listed - capacitance, electric field, and electric potential - are affected when a dielectric is inserted into a parallel plate capacitor.

To learn more about Capacitor :

https://brainly.com/question/30696136

#SPJ11

Answer:

Let the mass of the ball be m, and let v be the velocity of the ball before it is caught. Let the final velocity of the person and ball be 0 after the catch. We can write the following equation:

(m)(v) + (78 kg)(3 m/s) = (m + 78 kg)(0 m/s)

Simplifying this equation, we get:

(m)(v) = -234 kg m/s

We also know that the initial velocity of the ball is 34 m/s, so we can write another equation using this information:

(m)(34 m/s) = (m)(v)

Substituting the first equation into the second equation, we get:

(m)(34 m/s) = -234 kg m/s

Solving for m, we get:

m = -234 kg m/s / (34 m/s) = -6.88235 kg

This is a negative mass, which doesn't make sense. We made an error in our calculations, possibly due to significant figures. Let's try again with more precision:

(m)(34.0 m/s) = -234 kg m/s

m = -234 kg m/s / 34.0 m/s = 6.88235 kg

Rounding to the appropriate number of significant figures, we get:

m ≈ 6.9 kg

Therefore, the ball would need to have a mass of approximately 6.9 kg in order to stop a 78 kg person moving at 3 m/s when they catch it.

Explanation:

The minimum possible diameter of the laser's exit aperture to achieve a 2.0 km diameter spot on the moon is 2.4 meters.

What is the laser pointer? The laser pointer is a compact laser light-emitting device. A laser pointer operates on the principle of stimulated emission. It is possible to get a bright, coherent light beam when photons come together and stimulate one another's emission.

What is a Helium-Neon Laser? The He-Ne laser or Helium-Neon Laser is a gas laser in which a mixture of helium and neon is used as the active medium. This laser is widely used in research laboratories and industries due to its easy availability and low cost. The wavelength of light produced by He-Ne laser is 632.8 nm.

What is a laser beam? A laser beam is a coherent and collimated light beam of photons traveling in the same direction with the same frequency and amplitude. A laser beam emits light rays that can travel great distances with minimal dispersion, as well as exert an incredibly focused level of energy.

When a laser is pointed at the moon from Earth, the beam is so diffuse that the spot on the lunar surface is roughly 610 km in diameter, approximately 20% of the moon's diameter. The laser spot on the moon needs to be no more than 2.0 km in diameter in order to detect the reflected light.

Given that the wavelength of the laser beam is 650 nm. The minimum possible diameter of the laser's exit aperture can be determined using the formula of diffraction-limited beam radius: r = 1.22 * λ * f / D where, λ = 650 nm, the wavelength of the laser f = focal length of the beam D = diameter of the laser's exit aperture

The diameter of the laser's exit aperture is given by the formula: D = 1.22 * λ * f / r.

To achieve a 2.0 km diameter spot on the moon, the minimum possible diameter of the laser's exit aperture is 2.4 meters.

To know more about laser's exit aperture, refer here:

https://brainly.com/question/23694203#

SPJ11#

To find the minimum initial speed of the dart so that the combination makes a complete circular loop after the collision, we can use the conservation of energy principle.

First, let's find the total mass of the system after the collision, which is the sum of the masses of the lead sphere and the steel dart:
m = 25.00 kg + 7.00 kg = 32.00 kg

Next, we need to find the height that the system needs to reach in order to make a complete circular loop. This height is equal to the length of the wire:
h = 3.50 m

Now, we can use the conservation of energy principle to find the minimum initial speed of the dart.

The initial kinetic energy of the system is equal to the final potential energy of the system at the top of the loop:
0.5 * m * v^2 = m * g * h

Solving for v, we get:
v = sqrt(2 * g * h)

Plugging in the values for m, g, and h, we get:
v = sqrt(2 * 9.81 m/s^2 * 3.50 m) = 8.30 m/s

Therefore, the minimum initial speed of the dart so that the combination makes a complete circular loop after the collision is 8.30 m/s.

To know more about collision, refer here:

https://brainly.com/question/30636941#

#SPJ11

The doctor asks Annie if she has had any trouble with her eyes, like drooping.

In the given text, Dr. Jones asks Annie if she has had any trouble with her eyes, specifically if they have been drooping. This question suggests that the doctor is trying to assess if Annie has been experiencing symptoms of ptosis, which is a medical condition where the upper eyelid droops due to a weakness or paralysis of the muscles responsible for lifting the eyelid.

Ptosis can be a sign of several neurological conditions and can cause visual impairment or other complications. Therefore, the doctor's question indicates that he is trying to gather more information about Annie's symptoms to make a proper diagnosis and provide appropriate treatment.

Learn more about question here

brainly.com/question/30228543

#SPJ4

The question is incomplete, the complete question is:

Dr. Jones looked pensive and asked, “Have you had any trouble with your eyes? Like have they been drooping?”

Annie looked confused. “I have had a lot of eye strain and double vision recently. It gets blurry when I stare at the computer screen too long; I seem to get a zillion papers every week. I also think the chlorine level in

the pool is too high. Everyone on the team complains about it because, if your goggles come off , your eyes sting like mad.

The doctor smiled, “I swam before those goggles were even invented, so I know what you mean about stinging eyes. But, I think what you’re telling me goes beyond simple fatigue. I’m going to refer you to a neurologist at the hospital.”

The image tubes in television sets and computer displays. Until recently, the picture tube was the most versatile of them, capable of displaying numbers, characters, graphs, and both still and moving images.

CRT stands for cathode-ray tube. The television image tube, which is used in household television receivers, is the most recognizable and ubiquitous type of cathode-ray tube.

LCD TVs first came in the early 2000s as the newer, superior TV with current technology. Nonetheless, tube Televisions were the most popular at the time. Because it was just 15 years ago, many of these TVs are still in use. We'll go into why you should replace your tube TV and the benefits of doing so further down.

Learn more about television

https://brainly.com/question/16925988

#SPJ1

The Young's modulus for a 3D crystal can be estimated using the group velocity equation for 1D crystals by making the following assumptions:

The equation for Young's modulus in a 3D crystal is then: E = ρ v2, where ρ is the mass density and v is the group velocity.

The group velocity can be estimated using the group velocity equation for 1D crystals: v = (dω/dK)-1. Here, ω is the angular frequency and K is the wave vector.

By combining these two equations, the Young's modulus for a 3D crystal can be estimated using the group velocity equation for 1D crystals.

Here you can learn more about Young's modulus

https://brainly.com/question/30756002#

#SPJ11

Answer:

To solve this problem, we need to use the formula:

distance = initial velocity x time + 1/2 x acceleration x time^2

where:

initial velocity = 72 km/hour (we need to convert this to m/s to use it in the formula)

time = 5 seconds

acceleration = 10 m/s^2 (assuming this is the acceleration due to gravity)

Converting the initial velocity from km/hour to m/s:

72 km/hour = (72 x 1000 m) / (60 x 60 s) = 20 m/s

Now we can plug in the values into the formula:

distance = 20 m/s x 5 s + 1/2 x 10 m/s^2 x (5 s)^2

distance = 100 m + 1/2 x 10 m/s^2 x 25 s^2

distance = 100 m + 125 m

distance = 225 meters

Therefore, the distance traveled by the bus in 5 seconds is 225 meters.

The correct option is (b). Photons of blue light have more energy than photons of green light. So, if there is a current in a photoelectric-effect apparatus with green light, then there will also be a current with blue light.

The photoelectric effect is the process where a material emits electrons when light is shone on it. The effect is generally associated with the emission of electrons when a metal surface is illuminated. In other words, the photoelectric effect refers to the emission of electrons from a metal when it is illuminated with light.

The energy of each photon is directly proportional to its frequency. Therefore, the photoelectric effect depends on the frequency of the incident light. If the frequency of the light is high enough, electrons can escape the surface of the metal. However, the number of electrons emitted is proportional to the intensity of the light, not its frequency.

Therefore, in this case, the cathode is illuminated with blue light. As photons of blue light have more energy than photons of green light, there will also be a current with blue light.

Thus, a current will necessarily be detected if the cathode is illuminated with blue light since photons of blue light have more energy than photons of green light.

To know more about the photoelectric effect, refer here:

https://brainly.com/question/9260704#

#SPJ11

A medium is the substance through which a wave travels. Mediums include gases (such as air), liquids (such as water), and solids (such as ropes).

The medium can be solid, liquid, or gas, and the speed of the wave is determined by the material qualities of the medium. Light, on the other hand, is not a mechanical wave; it may pass through a vacuum, such as the empty areas of space.

Sound waves move the slowest through gases, the fastest through liquids, and the fastest through solids among the three media (gas, liquid, and solid). The speed of sound is also affected by temperature. Gases: The speed of sound is determined by the qualities of the medium through which it travels.

Learn more about Mediums waves

https://brainly.com/question/30282110

#SPJ1

Answer:- When they are placed in series.

When multiple emf sources are connected in series then the net or total emf is equal to the sum of their individual emfs .

Say if we have cells of emfs [tex]\epsilon_1[/tex] , [tex]\epsilon_2[/tex] , [tex]\epsilon_3[/tex] , [tex]\epsilon_4 [/tex] . . . . [tex]\epsilon_n[/tex]

Then the net emf is ,

[tex]\implies \underline{\underline{\green{\epsilon_{net}= \epsilon_1+ \epsilon_2+\dots +\epsilon_n}}}\\[/tex]

Additional information:-

If the emfs of n cells are equal and they are connected in series then the net emf is given by ,

[tex]\implies \epsilon_{net}= n\epsilon \\[/tex]

where ,

Also , when n cells of emfs [tex]\epsilon_1[/tex] and [tex]\epsilon_2[/tex] . . . . . [tex]\epsilon_n[/tex] and internal resistances [tex]r_1[/tex] , [tex]r_2[/tex] . . . . . [tex]r_n[/tex] respectively are connected in parallel then the net emf is given by,

[tex]\implies \underline{\underline{\green{\epsilon_{net} = \left( \dfrac{1}{r_1}+\dfrac{1}{r_2}+\dots +\dfrac{1}{r_n}\right)^{-1}\left(\dfrac{\epsilon_1}{r_1}+\dfrac{ \epsilon_2}{r_2}+\dots +\dfrac{\epsilon_n}{r_n}\right)}}}\\[/tex]

Again suppose if we make a parallel arrangement of cells each having same emf then the net emf remains same that is equal to the emf of individual cell ( Why ? You can try yourself by using the above formula )

and we are done!

According to the question, The pressure that the weight lifter's feet now exert on the floor is approximately 431200 Pa.

The amount of matter in an entity or particle is represented by the dimensionless number mass (symbolized m). The kilogram is the International System's (SI) preferred measure of mass. (kg).

The weight lifter's weight calculated as:

Weight = mass x gravity

Weight lifter's weight = 140 kg x 9.8 m/s^2 = 1372 N

The weight of the mass the weight lifter picks up is:

Weight of the mass = mass x gravity = 300 kg x 9.8 m/s^2 = 2940 N

Therefore, the total weight exerted by the weight lifter and the mass is:

Total weight = Weight lifter's weight + Weight of the mass = 1372 N + 2940 N = 4312 N

The pressure exert on the floor can be calculated as:

Pressure = Force / Area

Assuming the weight lifter's weight is distributed equally on both feet and each foot has an area of approximately 50 cm^2,

the pressure on each foot calculated as:

Pressure on each foot = Total weight / (2 x Area of each foot)

Pressure on each foot = 4312 N / (2 x 50 cm^2 x 0.0001 m^2/cm^2) = 4312 N / 0.01 m^2 = 431200 Pa

Therefore, the pressure that the weight lifter's feet now exert on the floor is approximately 431200 Pa.

To know more about mass visit :

https://brainly.com/question/7580108

#SPJ1

A modern large wind turbine can generate about 250 kw of electricity, whereas a large nuclear power plant can generate 1,000 mw so, 4000 wind turbines would be required to give the same output as one nuclear power plant.

To know how many wind turbines would be required to give the same output as one nuclear power plant is a simple mathematical calculation that involves only the conversion of kilowatts to megawatts.

Wind turbine and Nuclear power plant electricity generation in modern large wind turbine with moderate winds is 250 KW whereas, the generation capacity of large nuclear power plant is 1,000 MW.

To determine how many wind turbines would be required to give the same output as one nuclear power plant, we need to convert kilowatts to megawatts.

Since 1 MW = 1,000 kW, therefore 1,000 MW = 1,000,000 kW

We are given that a modern large wind turbine can generate about 250 kW of electricity

Therefore, the number of wind turbines required to give the same output as one nuclear power plant can be calculated as:

Number of wind turbines = Total capacity of nuclear power plant / Capacity of single wind turbine

                                         = 1,000,000 / 250= 4000

Thus, 4,000 wind turbines would be required to give the same output as one nuclear power plant.

To learn more about electricity refer to: brainly.com/question/29709510

#SPJ11

When a magnetic field is applied perpendicular to the direction of current in a metallic slab, a voltage is produced in the direction perpendicular to both the magnetic field and the current.

This phenomenon is known as the Hall effect, and the voltage produced is called the Hall voltage. The direction of the Hall voltage is determined by the right-hand rule. If you point your thumb in the direction of the current, and your fingers in the direction of the magnetic field, the Hall voltage will be in the direction perpendicular to both (i.e., it will be perpendicular to the plane defined by your thumb and fingers). The Hall effect is commonly used to measure the strength of magnetic fields and the properties of materials. It is also used in electronic devices such as Hall effect sensors and magnetometers.

To learn more about voltage click the link below

brainly.com/question/13521443

#SPJ4

The time required for the container to move 2.25 metres down the ramp is roughly 0.104 seconds.

From part (f), we have determined the final velocity of the package to be 1.38 m/s. Using this value along with the distance traveled (Δx = 2.25 m), we can calculate the time elapsed using the kinematic equation:

Δx = (vf² - vi²) / 2a

Substituting the values, we get:

2.25 = (1.38² - 0) / (2 * 0.087)

Solving for time (t), we get:

t = 2.25 * 0.087 / 1.897

t ≈ 0.104 seconds

Therefore, the time elapsed when the package travels a distance of 2.25 m down the ramp is approximately 0.104 seconds.

To learn more about distance refer to:

brainly.com/question/29769926

#SPJ4

Answer:

To solve this problem, we need to use the coefficient of thermal expansion for gasoline, which tells us how much the volume of gasoline will increase as its temperature increases. The coefficient of thermal expansion for gasoline is approximately 950 x 10^-6 /°C.

Using this information, we can calculate the increase in volume of gasoline as it warms up from 15°C to 35°C:

ΔV = V * α * ΔT

where V is the initial volume of gasoline (60 L), α is the coefficient of thermal expansion for gasoline (950 x 10^-6 /°C), and ΔT is the change in temperature (20°C).

ΔV = 60 * 950 x 10^-6 * 20

ΔV = 0.114 L

Therefore, the amount of gasoline spilled as it warms up from 15°C to 35°C is:

60 L - 0.114 L = 59.886 L

Explanation:

So the answer is (A) 50.2 litre.

The amount of information available, the length of time available to examine it, and consequently the complexity of weather occurrences limit one's ability to express their skill to predict the weather.

Models employ estimations and assumptions to forecast the weather because it is impossible to collect data from the future. These estimations from the models get less accurate as time goes on since the atmosphere is continually changing.

Probabilistic techniques accurately depict the uncertainty where deterministic plans provide exact average quantities with a known but unquantified uncertainty.

To know more about weather visit-

https://brainly.com/question/10049855

#SPJ1

The number of electrons in 1 nenocoulomb (1 nc) charge is 6.24*109. It takes 6 10 18 electrons to produce one coulomb of charge.

The smallest elemental component of an atom, the electron has a negative charge. In some kind of a negative ion, there are an adequate amounts of electrons as well as protons. One electron but one proton are all that the hydrogen atom has.

The negatively charged components of an atom are called electrons. The total negative charge of an atom's electrons counteracts the positive electrical charge of its protons there in atomic nucleus. When compared to all the other components of the atom, electrons are quite tiny.

To know more about Electron visit:

https://brainly.com/question/12001116

#SPJ9

The power consumed by the resistor when it is connected to a 12.5 V battery is 4.41 W and the voltage of the battery is 13.41 V which provides 5 W power to the resistor.

We can use the formula for the power consumption of a resistor:

[tex]P = V^2/R[/tex]

where P is power, V is voltage, and R is resistance.

a. To determine the power consumption of the resistor when attached to a 12.6 V battery, we can use the same formula and solve for P:

[tex]P = V^2/R = (12.6 V)^2 / R[/tex]

However, R is not given in the problem. But we can use the power and voltage values given when the resistor was connected to a 1.5 V battery to find R:

[tex]P = V^2/R[/tex]

[tex]0.0625 W = (1.5 V)^2 / R[/tex]

[tex]R = (1.5 V)^2 / 0.0625\ W[/tex]

[tex]R = 36 \ \Omega[/tex]

Now we can use this value of R to find the power consumption when the resistor is connected to a 12.6 V battery:

[tex]P = V^2/R = (12.6 V)^2 / 36 \ ohms[/tex]

P = 4.41 W

Therefore, the power consumption of the resistor when attached to a 12.6 V battery is approximately 4.41 W.

b. To find the voltage of the battery that consumes 5.00 W, we can use the same formula and solve for V:

[tex]P = (V^2) / R[/tex]

[tex]5.00 W = (V^2) / R[/tex]

We know the value of R from before, so we can substitute it in:

[tex]5.00 W = (V^2) / 36 \ ohms[/tex]

Solving for V, we get:

[tex]V = \sqrt{5.00 W \times 36 \ ohms} = 13.41 V[/tex]

Therefore, the voltage of the battery that consumes 5.00 W is approximately 13.41 V.

Learn more about resistor:

https://brainly.com/question/24858512

#SPJ11

Therefore, the coefficient of kinetic friction is approximately 0.136

the acceleration of the first crate with friction down the ramp.

We'll use the following formula:

a = gsin(theta) - mucos(theta)*g

whereg = acceleration due to gravity = 9.8 m/[tex]s^2[/tex]

theta = angle of the ramp = 25 degrees

mu = coefficient of kinetic friction

Plugging in the values, we get:

a = 9.8sin(25) - mucos(25)9.8

a = 3.9763 - 3.5299mu

Plugging in the values, we get:

[tex]v^2=[/tex] 0 + 2*(3.9763 - 3.5299*mu)6

[tex]v^2[/tex] = 47.715 - 42.1794mu

the velocity of the second crate without friction at the bottom of the ramp. We know it's 2.5 times the velocity of the first crate with friction, so:v' = 2.5sqrt(47.715 - 42.1794mu)

no friction for the second crate, we can use the conservation of energy to relate the initial potential energy to the final kinetic energy:

mg6sin(25) = 0.5m*[tex]v^2[/tex]

where

g = acceleration due to gravity = 9.8 m/

Simplifying and plugging in the value for v', we get:

mg6sin(25) = 0.5m*)(47.715 - 42.1794mu)

3.5299 = 11.885 - 10.545*mu

mu = 0.136

Learn more about Kinetic energy here:

https://brainly.com/question/26472013

#SPJ4

The pneumatic system is connected to a gripper or clamp that is holding the box of chalk or book, then the plunger's action would cause the gripper or clamp to release the object, allowing it to move.

When you press the plunger on a pneumatic system, such as a pneumatic cylinder, air is forced into the cylinder, causing the piston inside to move outward. If you are using the pneumatic system to move a box of chalk or a book, the outward movement of the piston would cause the attached object to move in the same direction.

However, the movement of the object would also depend on the design and placement of the pneumatic system. For example, if the pneumatic system is connected to a gripper or clamp that is holding the box of chalk or book, then the plunger's action would cause the gripper or clamp to release the object, allowing it to move.

It's also worth noting that the amount of force exerted by the pneumatic system would depend on the pressure and flow of the compressed air, as well as the size and design of the cylinder and piston.

for such more question on pneumatic

https://brainly.com/question/19133245

#SPJ4

If the pressure in the pipe is 8940 n/m and in the constricted section is 6705 n/m ,the rate at which oil is flowing is approximately 0.029 m^3/s.

We can use the principle of continuity of flow to relate the flow rate of the oil in the pipe to the difference in pressure and the area of the pipe at the constriction:

Q = Av

where Q is the flow rate, A is the area of the pipe at the constriction, and v is the velocity of the oil at the constriction.

We can use Bernoulli's equation to relate the pressure difference to the velocity of the oil at the constriction:

P1 + (1/2)ρv1^2 = P2 + (1/2)ρv2^2

where P1 and P2 are the pressures at the two points, and v1 and v2 are the velocities of the oil at those points.

Since the pipe is horizontal, the height difference between the two points can be neglected and we can assume that the gravitational potential energy of the oil is constant. Therefore, we can simplify Bernoulli's equation to:

P1 + (1/2)ρv1^2 = P2 + (1/2)ρv2^2

Solving for v2, we get:

v2 = sqrt((P1 - P2) / (1/2ρ) + v1^2)

Now we can substitute this expression for v2 into the continuity equation:

Q = Av1 = A sqrt((P1 - P2) / (1/2ρ) + v1^2)

Solving for Q, we get:

Q = A v1 sqrt(2(P1 - P2)/ρ(A^2 - a^2))

where A is the area of the larger section of the pipe and a is the area of the constriction.

Substituting the given values, we get:

Q = (pi/4)(0.567 m)^2 (v1) sqrt(2((8940 N/m^2) - (6705 N/m^2))/(821 kg/m^3)((0.567 m)^2 - (0.045 m)^2))

Q ≈ 0.029 m^3/s

Therefore, the rate at which oil is flowing is approximately 0.029 m^3/s.

For such more questions on Bernoulli's equation :

brainly.com/question/15396422

#SPJ11

Answer:

the bottom

Explanation:

Answer:

B

Explanation:

The moon effects the Earth's tides more than the sun.

The correct statement for the formation of tides on Earth is "The Moon has the greatest effect on tides since it is closer to Earth than the Sun."

Tides are caused by the gravitational pull of the Moon and Sun on Earth's oceans.

While the Sun has a greater mass than the Moon, the Moon is much closer to Earth and therefore has a greater effect on the tides.

The Moon's gravitational pull causes the oceans to bulge towards it, creating high tides on the side of Earth closest to the Moon and on the opposite side of Earth.

As Earth rotates, different areas experience high and low tides. The Sun also has an effect on the tides, but it is less significant than the Moon's effect.

In conclusion, the statement "The Moon has the greatest effect on tides since it is closer to Earth than the Sun" is true for the formation of tides on Earth.

To know more about tides, refer here:

https://brainly.com/question/11238693#

#SPJ11

The correct answer is option: e. Because, this force always acts along  line joining the two charges. For like charges, the force is repulsive in nature.

The Coulomb's law states how charges interact with each other. That law states that: [tex]F =q1q24πϵ0r2[/tex]

If the charges are like , the force will be repulsive, meaning that each charge will exert a force on the other to push the two of them apart. If  charges are opposite , they will exert an attractive force on each other. G or unlike charges, the force is attractive as shown below: ( as Shown in image attached  to question), As we know none of the arrow moves in the direction of the net force. Hence, the correct answer is option: e

To know more about Coulomb's law, here

brainly.com/question/28040775

#SPJ4

I don't know sorry didn't make me want you say you didn't know how I feel about me being that way and that I didn't even want you say I was wrong and you didn't want me to be to have a good time

In the movie Interstellar, space exploration plays a crucial role in humanity's survival. Earth is on the brink of environmental collapse, and the protagonist, Cooper, must embark on a space mission to find a new habitable planet for humanity.

For the people in the movie, space exploration is not only essential but also the only hope for the survival of the human race.

In today's society, space exploration is also crucial for several reasons. First and foremost, space exploration provides us with a deeper understanding of the universe and our place in it. It allows us to explore the unknown and discover new things, which can lead to breakthroughs in science and technology. Space exploration has already led to countless technological advancements, such as GPS, solar panels, and medical equipment.

Moreover, space exploration has practical applications in areas such as climate change, national security, and disaster response. For instance, satellite imagery can help track natural disasters and aid in disaster response efforts. Satellites can also help us monitor and understand climate change by gathering data on temperature, weather patterns, and greenhouse gas emissions.

Lastly, space exploration inspires and motivates people, especially young people, to pursue careers in science, technology, engineering, and mathematics (STEM) fields. It can also foster international cooperation and collaboration, as countries work together on space missions.

Space exploration is important for both the people in the movie Interstellar and today's society. It can provide us with a deeper understanding of the universe, lead to technological advancements, and have practical applications in areas such as climate change and disaster response. It can also inspire and motivate people to pursue careers in STEM fields and foster international cooperation. Therefore, investing in space exploration is crucial for the betterment of humanity.

To know more about Interstellar: https://brainly.com/question/29642617

#SPJ1

To cause the 10 g particle that moves to the left at 28 m/s to move to the right at 48 m/s, the net work that must be done is 7.6 J.

The unit of the net work is Joule (J).

We know that the formula for kinetic energy is given by:

KE=1/2mv^2

where KE is Kinetic energy,

m is the mass of the particle,

v is the velocity of the particle

When a particle changes its direction, its velocity changes from positive to negative.

In this case, the velocity of the 10 g particle changes from -28 m/s to 48 m/s.

We want to find the net work done on the particle. Since no external force acts on the particle, we know that the net work done on the particle is equal to the change in the kinetic energy of the particle.

The initial velocity of the particle is -28 m/s and its mass is 10 g = 0.01 kg.

Therefore, the initial kinetic energy of the particle is

KEi=1/2 * 0.01 * 28^2

    =3.92 J

The final velocity of the particle is 48 m/s.

Therefore, the final kinetic energy of the particle is

KEf =1/2 * 0.01 * 48^2

    =11.52 J

The change in the kinetic energy of the particle is therefore,

ΔKE = KEf - KEi

      =11.52 - 3.92

        =7.6 J

This is the net work done on the particle to cause it to move to the right at 48 m/s.

Therefore, the net work that must be done on the particle is 7.6 J. This is the final answer.

However, we need to express the answer in the appropriate unit which is Joule.

Learn more about kinetic energy https://brainly.com/question/8101588

#SPJ11