a tensile test was conducted on an aluminum specimen of 2.95 mm radius. the tensile peak load was recorded as 4281 n. 5pts a) find the ultimate tensile stress in mpa. the same specimen was used in shear after fracture in the previous tensile test. the new radius was recorded as 2.9 mm and the shear force of 4100 n. b) find the stress in mpa.

Answer:

Explanation:

The block has shrunk by about 45.3% based on the volume change, which is -0.453 times the initial volume.

The expression's negative sign indicates how the excessive pressure applied caused the material's volume to shrink. In other words, a decrease in volume will result from an increase in pressure. The volume change will be negative if pressure P is positive.

ΔV/V = -3K ΔP

K = E/(3(1-2v))

Given:

[tex]E = 60 GPa = 60 x 10^9 Pa[/tex]

v = 0.25

a = 100 mm = 0.1 m

b = 50 mm = 0.05 m

c = 60 mm = 0.06 m

F1 = 1801 N

F2 = 50 kN = 50000 N

F3 = 100 kN = 100000 NF_total = F1 + F2 + F3

F_total = 1801 N + 50000 N + 100000 N

F_total = 151801 NΔP = F_total / (abc)

ΔP = 151801 N / (0.1 m x 0.05 m x 0.06 m)

[tex]ΔP = 5.0337 x 10^7 Pa[/tex]

Finally, we can calculate the fractional change in volume using the formula:

ΔV/V = -3K ΔP

[tex]K = E/(3(1-2v)) = 60 x 10^9 Pa / (3(1-2(0.25))) = 6.0 x 10^10 Pa[/tex]

[tex]ΔV/V = -3(6.0 x 10^10 Pa) (5.0337 x 10^7 Pa)[/tex]

ΔV/V = -0.453

To know more about volume visit:-

https://brainly.com/question/22443936

#SPJ1

Note that the equivalent permeability kV(eq) is 8.19x10⁻³ cm/sec, the equivalent permeability kH(eq) is 4.59x10⁻⁴ cm/sec, and the ratio of kH(eq)/kV(eq) is 5.60.

To estimate the equivalent permeabilities kV (eq) and kH(eq) in cm/sec, and the ratio of kH(eq)/kV(eq) for the given layered soil, we need to use the following equations:

kV(eq) = (Σhi ki ) / Σhi

kH(eq) = Σhi²ki / Σhi²

kH(eq)/kV(eq) = Σhi ki / Σhi²ki

where hi is the thickness of the ith layer, and ki is the hydraulic conductivity of the ith layer.

Using the given data, we can calculate:

kV(eq) = [(1.2 x 1x10⁻¹) + (1.5 x 2x10³) + (3 x 1x10⁻³) + (9.5 x 2x10⁻⁴)] / (1.2 + 1.5 + 3 + 9.5) = 8.19x10⁻³ cm/sec

kH(eq) = [(1.2² x 1x10⁻¹) + (1.5² x 2x10⁻³) + (3² x 1x10⁻³) + (9.5² x 2x10⁻⁴)] / (1.2² + 1.5² + 3² + 9.5²) = 4.59x10⁻⁴ cm/sec

kH(eq)/kV(eq) = [(1.2 x 1x10¹) + (1.5 x 2x10⁻³) + (3 x 1x10⁻³) + (9.5 x 2x10⁻⁴)] / [(1.2² x 1x10⁻¹) + (1.5² x 2x10⁻³) + (3² x 1x10⁻³) + (9.5² x 2x10⁻⁴)] = 5.60

Therefore,  the equivalent permeability kV(eq) is 8.19x10⁻³ cm/sec, the equivalent permeability kH(eq) is 4.59x10⁻⁴ cm/sec, and the ratio of kH(eq)/kV(eq) is 5.60.

Learn more about soil permeabilities at:

https://brainly.com/question/27626099

#SPJ1

Answer:    

Explanation:

Both technicians A and B are correct. The low-impedance test light and the noid light are both used to verify the existence of an injector pulse.

What is a low-impedance test light?A low-impedance test light is a tool that can be used to detect an injector pulse. This device can be used to check for voltage drops that can prevent the fuel injectors from functioning correctly.What is a noid light?A noid light is a tool that is used to check for injector pulses. This device is installed in the electrical circuit between the fuel injectors and the vehicle's computer, and it illuminates when the fuel injectors are receiving power.What is an injector pulse?

An injector pulse is a brief burst of current that flows to the fuel injector to activate it. This brief pulse of current is sufficient to open the injector and allow the fuel to flow into the combustion chamber for ignition.What is an injector?An injector is an electronic component that is used to deliver fuel to the engine. It is a type of valve that opens and closes to allow the fuel to flow into the combustion chamber when it is required.

Learn more about  injector pulse at: brainly.com/question/14278715

#SPJ11

The difference between the two deflection values is 1.5 cm or 60%.

Using superposition, the deflection of the steel shaft at Point A is calculated by adding the contributions from the two forces:

Superposition is a principle used in engineering to analyze complex systems by breaking them down into simpler, more manageable parts. It is based on the assumption that the response of a linear system to a combination of inputs is equal to the sum of the responses of the system to each individual input.

Deflection at Point A = (1 x 1.5) + (3 x 0.5) = 4 cm

The deflection at midspan is calculated by adding the contributions from the two forces:

Deflection at midspan = (2 x 0.5) + (4 x 0.25) = 2.5 cm

The difference between the two deflection values is

(4 cm - 2.5 cm) = 1.5 cm or 60%.

To learn more about Deflection :

https://brainly.com/question/15692521

#SPJ4

Answer:

Explanation:

wkjefnewiapjdsfn[;sl/fn'sal/dfnsO"Jdfn[senkjsd;b;iwk/fj/hnd;kfjna/dlf.nkdfolsMan

A boost converter is a type of DC-DC converter that converts a lower input voltage into a higher output voltage. The boost converter shown in the question has an active switch, an inductor, a diode, and a capacitor.

(a) When the active switch is on, the circuit looks like this:

The current flows from Vin through the switch, the inductor, the diode, the capacitor, and the resistor, back to Vin. The direction of the current is indicated by the arrows.

When the active switch is off, the circuit looks like this:

The current flows from the inductor through the diode, the capacitor, and the resistor, back to the inductor. The direction of the current is indicated by the arrows.

(b) The plots of i, vip, ic, and v are shown below:

i(t) is the current through the inductor, which is constant and equal to I.

vip(t) is the voltage across the switch, which is equal to Vin when the switch is on and zero when the switch is off.

ic(t) is the current through the capacitor, which is equal to I when the switch is on and zero when the switch is off.

v(t) is the voltage across the resistor, which is equal to Vout when the switch is on and zero when the switch is off.

The values of i(t), vip(t), ic(t), and v(t) are labeled in terms of the given parameters I, Vin, and Vout.

Learn more about the direction of the current :

https://brainly.com/question/15912115

#SPJ11

Answer:

Electrical shock

Explanation:

Well insulated tools can help prevent the person using the tool have a less chance of getting electrocuted/ shocked.

Here's a Python program that takes a line of text as input, reverses it, and repeats until the user enters "Quit", "quit", or "q":

while True:

   line = input("Enter a line of text (or 'Quit' to exit): ")

   if line.lower() == "quit" or line.lower() == "q":

       break

   else:

       print(line[::-1])

In the above program, we use a while loop to repeatedly ask the user for input until they enter "Quit", "quit", or "q". Inside the loop, we use the input function to prompt the user for a line of text.

If the user enters "Quit", "quit", or "q", we use the break statement to exit the loop. Otherwise, we use slicing to reverse the line of text and print the result using the print statement.

For example, if the user enters "Hello there Hey quit", the program will output "tiuq yeH ereht olleH" (which is the reverse of the input line of text).

Note that we use the lower method to convert the input line of text to lowercase, so that we can check for different variations of "quit" (e.g., "Quit", "QUIT", etc.).

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11

The tank has a total volume of 1.78 m3, of which one third is in the liquid phase, and the remaining two thirds are in the vapour phase. The system has a density of 287.6 kg/m3.

Density is the measurement of how tightly a substance is packed. It has such definition since it is the mass per unit volume. The density symbol is D, and the density formula is The formula is: = m/V when is the density, m is the object's mass, and V is its volume.

Volume of vapor = (2/3) x 1.78 = 1.1867 m^3

Volume of liquid = (1/3) x 1.78 = 0.5933 m^3

To determine the density, we need to find the mass of the vapor and the mass of the liquid..

Mass of vapor = Volume of vapor / Specific volume of vapor = 1.1867 m^3 / 0.08609 m^3/kg = 13.785 kg

Mass of liquid = Volume of liquid / Specific volume of liquid = 0.5933 m^3 / 0.001190 m^3/kg = 498.3 kg

The total mass of the system is the sum of the mass of the vapor and the mass of the liquid:

Total mass = Mass of vapor + Mass of liquid = 13.785 kg + 498.3 kg = 512.085 kg

Finally, we can calculate the density using the total mass and the total volume of the system:

Density = Total mass / Total volume = 512.085 kg / 1.78 m^3 = 287.6 kg/m^3

To know more about volume visit:-

https://brainly.com/question/22443936

#SPJ1

Two categories of laser printers are personal and shared. Personal laser printers are designed for individual use, typically in a home or small office setting.

Shared laser printers are designed for use by multiple people in a larger office setting. It is important to note that the terms "active-matrix" and "passive-matrix" do not apply to laser printers, but rather to different types of LCD screens. "Thermal" and "ink-jet" are also not categories of laser printers, but rather different types of printers altogether. Laser printers use toner, rather than ink, to produce high-quality prints.

Learn more about matrix: https://brainly.com/question/2456804

#SPJ11

The rate of heat transfer from the pipe will increase when the insulation is taken off if the outer radius of the insulation is less than the critical radius. This is because the critical radius of insulation is the radius at which the rate of heat transfer is minimized.

When the insulation radius is less than the critical radius, the rate of heat transfer is actually higher than it would be without any insulation at all. Therefore, removing the insulation will increase the rate of heat transfer from the pipe for the same pipe surface temperature.

The critical radius of insulation can be calculated using the following formula:

[tex]r_c = k/h[/tex]

Where [tex]r_c[/tex] is the critical radius of insulation, k is the thermal conductivity of the insulation, and h is the heat transfer coefficient of the fluid surrounding the pipe. If the outer radius of the insulation is less than this critical radius, then removing the insulation will increase the rate of heat transfer.

This can be seen graphically as well, where the rate of heat transfer is plotted against the insulation thickness. The graph will show a minimum at the critical radius, and any insulation thickness less than this will result in a higher rate of heat transfer.

Learn more about insulation

https://brainly.com/question/18598066

#SPJ11

Web application 3’s “Where’s the Beef” exploit can be seen in the screenshot provided. In order to mitigate this vulnerability, developers should take measures to ensure that input validation is performed on all data.

Additionally, developers should enforce strict rules on which characters are allowed in user inputs and reject all requests that don’t follow these rules. Finally, developers should implement best practices such as password hashing to ensure that user data is secure.

Developers should use secure coding techniques, such as sanitizing user input and properly escaping HTML output, to protect against injection-based attacks. Also, developers should implement authentication and authorization techniques to ensure that only authorized users have access to sensitive data. Furthermore, developers should use an up-to-date web application firewall to protect against known exploits, and use secure protocols such as HTTPS to protect data in transit. Finally, developers should ensure that software is kept up-to-date and patched to prevent exploitation of known vulnerabilities.

Learn more about HTML

https://brainly.com/question/11569274

#SPJ11

The temperature of the tank after a 45-min period is estimated to be 30.908 K.

Temperature is a measure of how hot or cold something is relative to a standard reference point. It is typically measured in degrees Celsius (°C), Kelvin (K), or Fahrenheit (°F).

The rate of heat transfer can be estimated by using the following equation: Q = hA∆T

From the given data, the surface area of the tank is calculated as:

A = πr2 = π (0.25 m)2 = 0.19625 m2

The heat transfer coefficient for a windy environment can be estimated by using the following equation: h = 0.024V1/2, where V is the wind speed (m/s).

From the given data, the wind speed is calculated as: V = 40 km/h = 11.1 m/s

Therefore, the heat transfer coefficient is calculated as: h = 0.024 (11.1)1/2 = 0.92 W/m2K

The temperature difference between the air and the tank is calculated as:  ∆T = (Tair – Ttank) = (288 K – 308 K) = -20 K

Therefore, the rate of heat transfer is calculated as:

Q = hA∆T = (0.92 W/m2K) (0.19625 m2) (-20 K) = -3.7 W

Since the tank is losing heat, the rate of heat transfer is negative.

From the given data, the mass of the water in the tank is calculated as:

m = ρV = (1,000 kg/m3) (0.095 m3) = 95 kg

The specific heat capacity of water is assumed to be 4,186 J/KgK.

Therefore, the temperature difference is calculated as:

∆T = Q/(mc) = (-3.7 W)/ [(95 kg) (4,186 J/KgK)] = -0.0089 K

Therefore, the temperature of the tank after a 45-min period is estimated to be 30.908 K.

To learn more about temperature

https://brainly.com/question/15969718

#SPJ1

The magnitude of shear forces acting on as mentioned in the above case will be 600N .

What is shear force?

Shear force is defined as the force acting on a material in a direction opposite to its extension and parallel to a body's planar cross section.

a) The magnitude of shear forces acting on the upper and lower surfaces of the plate are:

                                           F(shear,upper)=τ(w,u)As

                                    F(shear,upper)=μAs[tex]mod[/tex](du/dy)

                                       F(shear,upper)=μAs (V-0)/h1     (V=5)

                                                 =(0.9)(2×0.5)(5-0)/10⁻²

                                                  =450N

     similarly,

                                  F(shear,lower)=μAs (V-0)/h2

                                                      =(0.9)(2×0.5)(5-0)/3×10⁻²

                                                         =150N

      Totally,       F=F(shear,upper)+F(shear,lower)

                            =450N+150N

                             =600N

To know more about shear force visit:

https://brainly.com/question/30216353

#SPJ9

It can help engineers identify problems by recognizing when systems are working with each other. Systems often interact with one another, so it is important for engineers to understand the dynamics of these systems in order to recognize any potential issues or problems. Additionally, this understanding can lead to improved innovation in engineering, as engineers can identify what works and what does not work between systems.

The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems.

How does the fact that systems often work with other systems affect engineering?

Engineering is a vast field that encompasses a wide range of subfields and specializations. Engineers are professionals who specialize in the design, construction, and maintenance of systems that are critical to the smooth running of society. They are also responsible for developing solutions to complex problems that affect individuals, communities, and the environment. Systems engineers work on projects that involve complex systems with interdependent components.

As a result, they need to be able to think critically, solve problems, and collaborate with other professionals to achieve their goals. The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems. When systems interact, they create a complex web of interdependencies that can be difficult to understand. Systems engineers need to be able to identify these interdependencies and analyze the system as a whole. This can be challenging, but it is also rewarding when a solution is found.

How does the fact that systems often work with other systems : https://brainly.com/question/17489470

#SPJ11

The theoretical fracture strength of the brittle material is estimated to be approximately 165.6 MPa when a stress of 1300 MPa is applied and fracture occurs by the propagation of an elliptically shaped surface crack of length 0.29 mm and tip radius of curvature of 0.004 mm.

To estimate the theoretical fracture strength of a brittle material given the information provided, we can use Griffith's theory of brittle fracture. According to this theory, the fracture strength of a brittle material can be expressed as:

σ_f = (2Eγπa)^0.5

where σ_f is the fracture strength, E is the elastic modulus, γ is the surface energy per unit area, and a is the length of the elliptically shaped surface crack.

To calculate the fracture strength, we need to first determine the surface energy per unit area of the material. For glass, a typical value of surface energy is around 1 J/m^2.

Given the length of the elliptically shaped surface crack (a) is 0.29 mm, and the tip radius of curvature is 0.004 mm, we can calculate the crack area (A) as follows:

A = πab = π(0.29/2)(0.004)

A ≈ 5.67 x 10^-7 m^2

Next, we can calculate the elastic modulus (E) of the material. For glass, the elastic modulus is typically around 70 GPa.

Substituting these values into the equation for fracture strength, we get:

σ_f = (2Eγπa)^0.5 = [2(70 x 10^9)(1)(π)(0.29 x 10^-3)]^0.5

σ_f ≈ 165.6 MPa

Learn more about theoretical fracture strength at: https://brainly.com/question/13707729

#SPJ11

Both technicians are correct in their statements about the use of a digital multimeter (DMM).

Technician A is correct in stating that back-probing is a technique used to reduce the chance of damage while measuring. This is because back-probing allows for the measurement of electrical signals without having to disconnect or damage the wires or connectors. It is a non-invasive method of measurement that reduces the risk of damage to the circuit or components.

Technician B is also correct in stating that insulation piercing probes do not increase the chance of corrosion or damage to the conductor. This is because these probes are designed to pierce the insulation of a wire without causing damage to the conductor inside. They allow for the measurement of electrical signals without having to strip the insulation, which can reduce the risk of corrosion or damage to the conductor.

Overall, both technicians are correct in their statements about the use of a DMM and the techniques used to reduce the chance of damage while measuring electrical signals.

You can learn more about digital multimeter (DMM) at

https://brainly.com/question/29737388

#SPJ11

A. For the equilateral triangle lattice, the diffraction pattern will show three bright spots in a triangular shape at each order. The first order will have the brightest spots, with the intensity decreasing as the order increases. The second and third orders will have less intense spots, but they will still be in the same triangular shape.

B. For the isosceles triangle lattice with height equal to base, the diffraction pattern will be similar to the equilateral triangle lattice, but the spots will be slightly more spread out due to the larger lattice spacing. The first order will still have the brightest spots, with the intensity decreasing as the order increases. The second and third orders will have less intense spots, but they will still be in the same triangular shape. The increase in energy from 10 keV to 100 keV will also cause the spots to be more spread out.

Overall, the diffraction pattern for both the equilateral and isosceles triangle lattices will be similar, with the main difference being the spacing of the spots due to the different lattice spacings and the increase in energy.

Learn more about isosceles triangle lattices

https://brainly.com/question/12025580

#SPJ11

The output voltage from the given transformer is 480 VA

The formula to determine the output voltage of a transformer is:

Ns / Np = Vs / Vp

Where:

Ns = Number of turns in the secondary coil

Np = Number of turns in the primary coil

Vs = Voltage in the secondary coil

Vp = Voltage in the primary coil

Let's put the values we have in this formula:

400/200 = Vs / 240

To find Vs, cross-multiply the above equation and simplify:

400 x 240 = 200 x VS

Vs = (400 x 240) / 200

Vs = 480

Therefore, the output voltage from the given transformer is 480 VAC.

Learn more about output voltage at

https://brainly.com/question/17188217

#SPJ11

Answer:

Workshop technology is the type of technology which deals with different processes by which component of a machine or equipment are made. Its purpose is that the module unit is designed to equip the trainee with knowledge, skills, and attitudes that enable to perform basic workshop tasks.

The vertical deflection of the bar at D can be determined by using the equation for deflection of a beam with a distributed load.

First, we need to calculate the moment of inertia (I) of the rod CB. The moment of inertia for a circular cross-section is given by:

I = (pi/4) * r^4

Where r is the radius of the cross-section. In this case, the cross-sectional area of the rod is 14mm^2, so we can calculate the radius as follows:

14mm^2 = (pi/4) * r^2

r = sqrt((14mm^2 * 4)/pi) = 2.12mm

Now we can calculate the moment of inertia:

I = (pi/4) * (2.12mm)^4 = 39.9mm^4

Next, we need to calculate the elastic modulus (E) of the 6061-T6 aluminum. The elastic modulus for this material is typically around 68.9 GPa (68.9 x 10^9 Pa).

Now we can use the equation for deflection of a beam with a distributed load to calculate the vertical deflection at D:

delta = (5/384) * (w * L^4)/(E * I)

Where delta is the vertical deflection, w is the distributed load, L is the length of the beam, E is the elastic modulus, and I is the moment of inertia. In this case, we have:

delta = (5/384) * (w * (0.8m)^4)/(68.9 x 10^9 Pa * 39.9mm^4)

Simplifying and converting units gives:

delta = (5/384) * (w * (800mm)^4)/(68.9 x 10^9 Pa * 39.9mm^4) = (1.05 x 10^-6) * w

Therefore, the vertical deflection of the bar at D is given by:

delta = (1.05 x 10^-6) * w

Where w is the distributed load in N/m.

Learn more about The vertical deflection of the bar:

https://brainly.com/question/17080885

#SPJ11

True, automotive applications use both AC and DC (direct current) motors. Nonetheless, AC motors are the type of electric motors seen in current electric and hybrid vehicles the most frequently.

While the motor of your electric vehicle runs on AC, the battery requires DC power. Hence, an onboard or external conversion from alternate to direct current is necessary. Grid electricity is always AC.

Direct current (DC) and alternating current (AC) both have advantages and disadvantages when used to power motors. In order to assess a DC motor for the purposes of this essay, visit here to read about AC motors. A DC motor's essential components include: Stator.

To know more about electric motors visit:-

https://brainly.com/question/21127297

#SPJ1

For 5°C and For 35°C the backwash velocity can be between 1.5-2 times the minimum fluidization velocity.  backwash rate will be between 0.069 m/s and 0.092 m/s for For 5°C and 0.078 m/s and 0.104 m/s For 35°C.

The terminal velocity and minimum fluidization velocity of filter sand can be calculated using the following equations:

Terminal velocity (Vt):

Vt = [4 × (ρp - ρf) × g × dp²] / (3 × Cd × ρf)

Minimum fluidization velocity (Umf):

Umf = [((1 - ε) × g × dp³ × (ρp - ρf)) / (150 × μ × ε³)]¹/⁴

Where:

ρp is the density of the filter sand particles (assumed to be 2650 kg/m³)

ρf is the density of the fluid (water, assumed to be 1000 kg/m³)

g is the acceleration due to gravity (9.81 m/s²)

dp is the effective diameter of the filter sand (0.50 mm)

Cd is the drag coefficient (assumed to be 0.44 for a smooth sphere)

ε is the porosity of the filter bed (0.45)

μ is the dynamic viscosity of the fluid (1.787 x 10⁻³ Pa s at 5°C, and 1.138 x 10⁻³ Pa s at 35°C)

Substituting the given values, we get:

For 5°C:

Vt = [4 × (2650 - 1000) × 9.81 × (0.0005)²] / (3 × 0.44 × 1000)

= 0.037 m/s

Umf = [((1 - 0.45) × 9.81 × (0.0005)³ × (2650 - 1000)) / (150 × 1.787 × 10⁻³ × 0.45³)]¹/⁴

= 0.046 m/s

Backwash velocity can be between 1.5-2 times the minimum fluidization velocity, thus the appropriate backwash rate will be between 0.069 m/s and 0.092 m/s.

For 35°C:

Vt = [4 × (2650 - 1000) × 9.81 × (0.0005)²] / (3 × 0.44 × 1000)

= 0.042 m/s

Umf = [((1 - 0.45) × 9.81 × (0.0005)³ × (2650 - 1000)) / (150 × 1.138 x 10⁻³ × 0.45³)]¹/⁴

= 0.052 m/s

Backwash velocity can be between 1.5-2 times the minimum fluidization velocity, thus the appropriate backwash rate will be between 0.078 m/s and 0.104 m/s.

To learn more about backwash velocity click here

brainly.com/question/30215509

#SPJ4

The unknown capacitor in arm CD must have a value of 330 microfarads, and the unknown resistor must have a value of 100 kilo-ohms.

To solve the problem, use the following formula:
Cseries = C1 x C2 / (C1 + C2)

Where C1 is the value of the capacitor in arm AB (47 microfarads) and C2 is the value of the capacitor in arm BC (330 microfarads).

Therefore, Cseries = 330 microfarads.

Also, the total resistance of arms CD is the sum of the resistance of the resistor (R) and the reciprocal of the capacitive reactance of the capacitor (1/Xc).

Using the following formula:
Rtotal = R + 1/Xc

Where Xc = 1/2πfC,

f is the frequency and C is the capacitance.

For this problem,

Xc = 1/2π(50)(330 x 10-6)

=> 100 kilo-ohm.

To learn more about Capacitor :

https://brainly.com/question/30426172

#SPJ4

The approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A is 5237692500 J/m³.

To calculate the approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A, follow these steps:

1. Calculate the power of the welding operation:

Power = Voltage × Current

Power = 25 V × 200 A = 5000 W

2. Determine the specific heat capacity of mild steel. The specific heat capacity of mild steel is approximately 450 J/kg·K.

3. Calculate the mass of mild steel per unit volume. The density of mild steel is approximately 7850 kg/m³.

4. Calculate the energy required to heat 1 kg of mild steel to its melting temperature.

Energy = Specific Heat Capacity × Mass × Temperature Change

Energy = 450 J/kg·K × 1 kg × (1776 K - 293 K)

Energy = 450 J/kg·K × 1 kg × 1483 K

Energy = 667350 J/kg

5. Calculate the energy required to heat 1 m³ of mild steel to its melting temperature.

Energy = Specific Heat Capacity × Mass × Temperature Change

Energy = 667350 J/kg × 7850 kg/m³

Energy = 5237692500 J/m³

Learn more about Energy:

https://brainly.com/question/25737117

#SPJ11

Answer:

Explanation:huioj;kml,bhujk'uyyghkjhiyugjhiyutgjhkjuiy

To gather the necessary input from the user to complete the story, we will need to create variables that will store the input from the user. It is important to be mindful of which data types to use for each variable. For string input, we should use `getline` instead of just `cin` by itself.

Here is an example of how to create the variables and gather the input from the user:

```cpp
// Declare variables
string name;
int age;
char gender;

// Get input from user
cout << "Enter your name: ";
getline(cin, name);
cout << "Enter your age: ";
cin >> age;
cout << "Enter your gender (M/F): ";
cin >> gender;
```

In this example, we have created three variables: `name` (string), `age` (int), and `gender` (char). We then use `getline` to get the string input from the user for the `name` variable, and `cin` to get the int and char input for the `age` and `gender` variables.

Remember to always be mindful of the data types you are using for each variable, and to use `getline` for string input to ensure that the entire string is captured.

Learn more about programming:

https://brainly.com/question/26134656

#SPJ11