The magnitude of the induced emf in the loop is 1mV.
The formula to be used is:
E = B (dA/dt)
B = magnetic of magnetic field parallel to the axis of loop = 0.5 T
dA/dt = rate of change of area of the loop = 20 cm²/s = 20 x 10⁻⁴ m²
θ = Angle of the magnetic field with the area vector = 0
E = emf induced in the loop
Now, plugging in the values we get:
E = B (dA/dt)
E = (0.5) (20 x 10⁻⁴ )
E = 10 x [tex]10^{-4}[/tex] volts
E = 1 mV
Therefore, the magnitude of the induced emf in the loop is 1mV.
Learn more about emf induced in the loop here:
https://brainly.com/question/16764848
#SPJ4
In the diagram below, two of the three rays used to find the image position are shown. Which of the following best describes the third (missing) ray?A.A ray incident parallel to the axis refracts outward, as if it came from the focus on the left hand side.B.A ray incident through the vertex continues through the lens without refracting.C.A ray incident parallel to the axis refracts so that it passes through the focus on the right hand side.D.A ray incident on a path that would take it through the right focus refracts parallel to the axis.
Answer:
C. A ray incident parallel to the axis refracts so that it passes through the focus on the right hand side
Explanation:
The third ray is the blue ray in the following figure
Therefore, the third ray is a ray parallel to the axis that refracts and passes through the focus of the right side.
So, the answer is:
C. A ray incident parallel to the axis refracts so that it passes through the focus on the right hand side
would not be an indication of a car getting ready to pull into your lane. a. a turn signal b. a hand signal c. wheels turned toward the street d. an open car door
The option that would not be an indication of a car getting ready to pull into your lane is an open car door ( d ).
Option A is an indication of a car getting ready to pull into your lane because a turn signal is an indicator installed in the car to indicate the change of lanes. Option C is an indication of a car getting ready to pull into your lane, but it is not a 100% indication, because not every driver is going to notice if your wheels are turned or not.
Option B is an indication of a car getting ready to pull into your lane during day time because during day time the turn signal might not be bright enough to see. So one probably uses hand signal to make sure that other drivers see clearly that you are about to change lanes.
Therefore, the option that would not be an indication of a car getting ready to pull into your lane is an open car door ( d ).
To know more about turn signal
https://brainly.com/question/4511065
#SPJ1
psychology is the ___ study of behavior and mental processes
Answer:
scientific study
Explanation:
I hope that helps
Answer:
scientific studies
give me brainlyest please
after driving a portion of the route, the taptap is fully loaded with a total of 27 people including the driver, with an average mass of 70 kgkg per person. in addition, there are three 15- kgkg goats, five 3- kgkg chickens, and a total of 25 kgkg of bananas on their way to the market. assume that the springs have somehow not yet compressed to their maximum amount. how much are the springs compressed? enter the compression numerically in meters using two significant figures. view available hint(s)
When something, like a spring, is stretched, the added length is referred to as its extension.According to Hooke's law, as long as the limit of proportionality is not crossed, a spring's extension is directly proportionate to the force exerted.
Solve the problem ?
The ends of an extension spring connect to two devices.The hooks and loops on the extension springs store and compress energy.An extension spring delivers return force to connected mechanisms via hooks or loops.The no-load position is where tightly wrapped extension springs normally rest. Total mass refers to the combined weight of the shell, its structural and support equipment, and the heaviest load that may be conveyed.The spring's compression at the specified weight is 0.80cm.
"Your inquiry is incomplete because it appears to be lacking the information below,"
The taptap's spring has a k value of 2.4 104 N/m.
the settings provided;
Each of the 27 people weighs 69 kg.
Each of the three goats weighs 15 kg.
Each of the five hens weighs 3 kg.
The weight of the bananas is 25 kg
The taptap's total mass, which includes every passenger, is computed as;
the people's combined mass is 27 x 70 or 1960 kg.
The goats' combined mass is 3 x 15 =45 kg.
The birds' combined mass is equal to 5 x 3 = 15 kg.
The bananas weigh a total of 25 kilograms
The extension of the spring
= 1960×9.8/2.4×104
= 19208/24000
= 0.80 cm
To learn more about spring extension refer
https://brainly.com/question/25559287
#SPJ4
A periodic wave has a wavelength of 1.6 m and a speed of 16 m/s. What is the wave frequency?
ANSWER
10 Hz
EXPLANATION
Given:
• The wavelength of a periodic wave, λ = 1.6 m
,• Its speed, v = 16 m/s
Find:
• The wave frequency, f
The frequency of a wave is given by the quotient between the wave's speed and its wavelength,
[tex]f=\frac{v}{\lambda}[/tex]Replace the known values and solve,
[tex]f=\frac{16m\/s}{1.6m}=10\text{ }\frac{1}{s}=10\text{ }Hz[/tex]Hence, the frequency of the wave is 10 Hz.
Equal masses are suspended from two separate wires made of the same material. The wires have identical lengths. The first wire has a larger cross-sectional area than the second wire. Which wire will stretch the least?.
The original lengths of both wires are equal, the thicker wire will stretch less as a result since Young's Modulus predicts that its original length will change less.
Young's modulus is a measurement of a material's capacity to endure changes in length when subjected to compression or tension along its length. Young's modulus, also known as the modulus of elasticity, is determined by dividing the longitudinal stress by the strain. i.e.Young's modulus = stress/strain
We can assume that the thicker wire must have less strain if it suffers less stress than the thinner wire because strain is defined as the percentage change in length.
Therefore we can said that, For the Young's modulus to remain constant, which it does, it must also drop correspondingly as strain rises. The thicker wire will stretch less as a result since its original length will change less because both wires started off the same length.
To know more about Young's Modulus
https://brainly.com/question/29033151
#SPJ1
A tennis player can accelerate a tennis ball at 295m/s² using an average force of
58 N with his racquet. What is the mass of the tennis ball?
answer of the question is into the picture ️
When resistors are put in series next to each other, their overall resistance isA. Larger than that of any individual resistorB.the same as the resistance of one of the resistorsC. Smaller than the resistance of any of the resistors
Answer:
A. Larger than that of any individual resistor
Explanation:
When resistors are put in series, the overall resistance is equal to the sum of all the resistances. So, the overall resistance will be larger than that of any individual resistor.
On his trip from home to school, Noah Omwerk drives along three streets after exiting the driveway. He drives 1.85 miles south, 2.43 miles east, and 0.35 miles north. Determine the magnitude of Noah's resultant displacement. And the angle from East to South.
The resultant displacement of Noah from the question is 2.9 miles.
What is the resultant displacement?The displacement is a vector quantity. Recall that a vector quantity is going to posses both a magnitude and a direction as we can see. This implies that the result of the vector which is the single vector that has the combines effect in magnitude and direction as all the vectors put together would be obtained by a geometric rather than an algebraic method. We now have to apply the rules that are used to obtain the resultant vector in each of the cases that does apply here.
We are now told that he drives 1.85 miles south, 2.43 miles east, and 0.35 miles north. The resultant of the vector in the North - South direction is; 1.85 miles - 0.35 miles = 1.5 miles.
Then the general resultant vector is obtained from;
R = √(1.5)^2 + (2.43)^2
R = 2.9 miles
Learn more about displacement:https://brainly.com/question/11934397
#SPJ1
a cart with a mass of 2.0 kg is pulled across a level desk by a horizontal foirce of 4.0n. if the coeffiecient of kinetic friciton is 0.12 what is the acceleration of the cart
Answer:
The acceleration of the cart:
a = 0.82 m/s²
Explanation:
Given:
m = 2.0 kg
F = 4.0 N
μ = 0.12
g = 9.8 m/s²
___________
a - ?
Friction force:
Ff = μ·m·g
2 Newton's law:
m·a = F - Ff
The acceleration of the cart:
a = ( F - Ff) /m
a = F/m - (μ·m·g) / m
a = F/m - μ·g
a = 4.0 / 2.0 - 0.12·9.8 ≈ 0.82 m/s²
Hey surveyor is drawing property lines . He draws one line that is 25.0 m long and is 20° south of west.  how long is the western component of the vector he has drawn?
Answer:
23.5 m
Explanation:
25 m * cos 20 =23.5 m
a lighthouse is located on a small island 5 km away from the nearest point p on a straight shoreline and its light makes seven revolutions per minute. how fast (in km/min) is the beam of light moving along the shoreline when it is 1 km from p? (round your answer to one decimal place.)
188.4 km/min is the beam of light moving along the shoreline.
The lighthouse is 5 km far away from the nearest Point P on a straight shoreline. This is often radius of the encirclement of the beam of light moving at 7 rpm.
At 7 rpm, One Circumference of the sunshine takes 70/7 = 10 seconds 2πr is= 2.π.5 km in 10 seconds or
In one second the beam covers 10π/10 = π km or 3.14 km/s.
Now, if the purpose P is 1 km away from the lighthouse, the Radius is reduced to 1 from 5 km,
Consequently The Angular displacement would remain the identical but the speed would be slower for one circumference i.e. 2πr in 10 seconds.
Or one second= (2π.1)/10
= .628π km
= π/10
= 3.14 km/s
By converting km/s into km/min
The answer will be = 188.4 km/min.
188.4 km/min fast (in km/min) is the beam of light moving along the shoreline when it is 1 km from point P.
To know furthermore about Angular Displacement at
https://brainly.com/question/12972672
#SPJ4
describe the forces that are acting on the cake as it falls and when it lands on the ground.
Answer:
gravitational force
Explanation:
expressed the weight of the object.
When the cake falls into the ground gravitational force and electromagnetic forces are working on it and when it lands on the ground gravitational, electromagnetic and normal force act on it.
What is Force?Force is the influence of either pull or pushes in the body. Basically, gravitation forces, nuclear forces, and friction forces are the types of forces. For e.g. when the wall is hit by a hand then a force is exerted by the hand on the wall as well as the wall also exerts a force on the hand. There are different laws given to Newton to understand force.
Two fundamental forces are at play while the ball falls: gravity, which causes the ball to descend, and electromagnetic forces, which causes the ball to interact with the air.
The gravity force still affects the ball when it strikes the ground, but it is less significant than the electromagnetic force generated by the earth and the ball itself. The deformation and restoration of the ball's shape are caused by the EM (electromagnetic) inside the ball. The ball stops descending due to the EM force with the earth.
So the simple answer is consistent with the other answers here: the electromagnetic force is responsible for the force between the ball and the ground.
To know more about forces:
https://brainly.com/question/13191643
#SPJ2
A tennis ball moves 22 meters southward, then 12 meters northward, then 16 meters southward, and finally 34 meters northward
The resultant displacement of the tennis ball is 8 m northward.
What is displacement?
The displacement of an object is the change in the position of the object. The displacement of an object describes the shortest point between the final and initial position of an object.
The displacement of the tennis ball is calculated as follows;
d = (12 m north + 34 m north) - (22 m south + 16 m south)
d = (46 m north) - (38 m south)
d = 8 m northward
Thus, the resultant displacement of the tennis ball for the given motion is 8 m northward.
Learn more about displacement here: https://brainly.com/question/2109763
#SPJ1
The compete question is below:
A tennis ball moves 22 meters southward, then 12 meters northward, then 16 meters southward, and finally 34 meters northward. find the resultant displacement of the tennis ball.
After every movement in north and south direction multiple times, the displacement of the tennis ball is 8 meters in north direction.
What is displacement?The definition of displacement is the modification of an object's position. It has a direction and magnitude and is a vector quantity. It is shown as an arrow that travels from the initial location to the conclusion.
According to the question, the tennis ball moves 22 meters in south direction then it moves towards north and travels for 12 meters again it turns to south and covers 16 meters and at last it covers 34 meters in the north direction.
d = (12 m + 34 m ) north direction - (22 m + 16 m ) south direction
d = 8 meters in north direction.
Hence, the total displacement done by the tennis ball is 8 meters in the north direction.
To get more information about Displacement :
https://brainly.com/question/19979064
#SPJ1
complete the table=x =0 2 3 4 6 8 y=30 27 24
Answer: (x=1 y=30) (x=2 y=27) (x=3 y=24) (x=4 y=21) (x=5 y=18) (x=6 y=15) (x=7 y=12) (x=8 y=9) (x=9 y=6) (x=10 y=3) etc its going down by 3 so 30-3=27 27-3=24 24-3=21 etc
hope i helped
Explanation:
5. An object travels with constant speed through 1km for one minutes and 20 seconds and accelerates with 0.125m/s² for 20 seconds, what is the total displacement? A) 1250 m B) 275 m C) 1275 m D) 1225m
Answer:
C) Total displacement = 1275 m or 1.275 km
Explanation:
We'll break this into two parts:
1) Displacement during constant speed, and
2) Displacement during the acceleration phase.
Constant Speed
The displacement for this segment is already stated: 1 km. But the information includes the time, which will allow us to calculate the speed of travel. We'll need this for the next phase of acceleration.
Distance = Speed x Time
Speed = Distance/Time
Time = 1 minute + 20 sec, or 80 sec.
Speed = 1 km/80 sec
Speed = 0.0125 km/sec
Since we'll be using meters (not km) in the next step, convert 0.0125 km/sec to m/sec with a conversion factor:
(0.0125 km/sec)*(1000m/1 km) = 12.5 m/sec
Acceleration Phase
The obect is moving at a speed of 12.5 m/sec (from above) and then accelerates at a rate of 0.125 m/sec^2 for 20 seconds.
The distance (s) an object travels during this acceleration (a) is gven by:
s = vi*t + (1/2)a*t^2,
where vi is the initial velocity (12.5 m/sec in this case), a is the acceleration (0.125 m/sec^2), and t is the time (20 seconds).
s = (12.5 m/sec)(20 sec) + (1/2)(0.125 m/sec^2)*(20 sec)^2
s = 275 meters
Now add the two distances:
1) Constant Speed Phase = 1000 m
2) Acceleration Phase = 275 m
Total displacement = 1275 m or 1.275 km
a 7.0 g bullet is fired into a 1.5 kg ballistic pendulum. the bullet emerges from the block with a speed of 200 m/s, and the block rises to a maximum height of 11.7 cm. find the initial speed of the bullet.
the initial speed of the bullet: 520.31 m/sec
using the conservation of linear momentum we write
m1u1 + m2 u2 = m1 v1 + m2v2
where u1 and u2 are the initial velocities of masses m1 and m2\
where v1, and v2 are the final velocities of masses m1 and m2\
hence (.007) (u1) + 1.5(0) = 1.5(v2) + .007(200)
using the energy equation for the block alone we get
mgh = 1/2 m (v2[tex])^2[/tex]
hence 9.8(.0117) =.5 (v2[tex])^2[/tex]
hence v2= 1.494 m/sec
substitute it in 1
we get,
(.007) (u1) + 1.5(0) = 1.5(1.494 ) + .007(200)
u1 =initial speed of the bullet= 520.31 m/sec
What is Speed?The definition of speed can be given as a measure of the distance travelled by an object and the time needed to travel the distance. Simply put, it is a measure of how fast an object is moving, but it does not give direction. If we get direction by speed, it is called "velocity".
Speed can be calculated in science. The speed formula is a formula derived from science and is used to calculate different speeds. The formula for speed is:
[tex]Speed = \frac{Distance}{Time}[/tex]
To learn more about speed, visit;
https://brainly.com/question/28224010
#SPJ4
The potential energy of a roller coaster is 50 joules. The kinetic energy of the same coaster is 50 joules. What is the mechanical energy of the coaster?.
A roller coaster's mechanical energy is equal to 100 Joules if its P.E. and K.E. are each 50 Joules.
As a result, the roller coaster has a mechanical energy of 100 Joules.
explanation?
50 Joules is the potential energy of a roller coaster.
A roller coaster has kinetic energy of 50 Joules.
In order to determine the roller coaster's mechanical energy:
The entire amount of potential energy (P.E.) and kinetic energy (K.E.) that an object or body possesses is known as mechanical energy.
(ME)=50+50
Mathematically, the formula for mechanical energy states that it is equal to 100 joules when the given values are substituted.
As a result, the roller coaster has a mechanical energy of 100 Joules.
To learn more about mechanical energy refer to:
https://brainly.com/question/18498239
#SPJ4
Instructions:Draw a speed graph in the box that matches thefollowing scenario:A runner jogged 40m at a slow pace for 40seconds. She then stopped for 40 seconds to gea drink of water. After that, she sped up and ran60m more in 20 seconds.Tip:y axis - total of 100 mx axis - total of 100 s
Given data:
1) Runner jogged 40 m at a slow pace for 40 sec.
2) Stopped for 40 sec.
3) Again funs for 60 m in 20 sec.
when resistors 1 and 2 are connected in series, the equivalent resistance is 13.6. when they are connected in parallel, the equivalent resistance is 2.40. what are (a) the smaller resistance and (b) the larger resistance of these two resistors?
The larger resistance is R₂ =12Ω.
Resistance values are expressed in ohms (Ω). when an electron differential exists among terminals, energy will float from excessive to low. Resistance counteracts that waft. The greater the resistance, the lower the current. Conversely, the decrease in the resistance, the extra the modern.
series connection:- R equivalent = R₁ + R₂
R₁ + R₂ = 13.6 Ω
R₁ = 13.6 Ω - R₂
parallel connection:- R equival;ent = R₁R₂ / R₁ + R₂
2.40 = R₁R₂ / R₁ + R₂
2.40 = R₁R₂ / 13.6 Ω
R₁R₂ = 2.40 × 13.6 Ω
R₁R₂ = 32.64 Ω
2.40 = R₁R₂ / R₁ + R₂
R₁ + R₂ = 32.64 Ω / 2.40 Ω
R₁ + R₂ = 13.6.
must be 4.0Ω and 13.6Ω, respectively.
(a) The smaller resistance is R₁ =4.0Ω
(b) The larger resistance is R₂ =12Ω
An electric-powered cutting-edge flows when electrons flow through a conductor, consisting of a metallic cord. The moving electrons can collide with the ions in the steel. This makes it greater tough for the present day to flow, and reasons for resistance.
Learn more about resistance here:-https://brainly.com/question/17563681
#SPJ4
What is the BEAT FREQUENCY when 512 Hz and a 515 Hz tuning forks are sounded at the same time?
The beat frequency is 3 beats/sec.
Beat frequency(n) can be found by using the following formula:
n=f2-f1, where f2 and f1 are the given frequencies
n= 515-512
n= 3 beats/sec
Therefore the beat frequency when 512 Hz and 512Hz tuning forks are sounded together is 3 beats/sec.
To learn more about beat frequency, click on https://brainly.com/question/14549472
one steel ball and one aluminum ball are the same size but the steel ball weighs twice as much as the other. the balls are dropped from the roof of a single-story building at the same instant of time. the time it takes the balls to reach the ground below will be:
It is same for both the balls. Due to the fact that balls fall freely regardless of their weight, both metallic balls take the same amount of time to reach the ground.
When two identically sized objects are dropped from a certain height, they will fall with gravitational acceleration (g). The weight of the objects will not affect how long it takes them to reach the ground. The density of the medium in which an object is dropped affects how long it takes for each object to travel there. Due to the influence of gravity and the same medium, we can therefore infer that both metal balls will take the same amount of time to reach the ground (air). Experiments have been conducted in vacuum rooms and show that when the balls are released from the top of the store, the acceleration of attraction to the floor is gravity and it has a value of 9.8 meters/square second regardless of its weight.
Learn more about gravity here-
https://brainly.com/question/4014727
#SPJ4
what is a tone? multiple choice question. a sound with definite and steady vibrations a note that is emphasized the distance between two pitches the distinctive sound quality of an instrument
A tone is a sound with definite and steady vibrations.
What is tone?
The author's attitude toward the topic they are writing about is the definition of tone in literature. The Latin word tonus, which means a sound or accent, and the French word tonne, which denotes a musical sound, are the origins of the word tone. Whether the author intends it or not, the reader always picks up on the tone of a work of literature. The words an author chooses as well as how they are used make up their diction. The way an author speaks affects the reader's mood. The syntax, point of view (a particular attitude as well as way of describing a subject), diction, and degree of formality used in writing all convey the tone of the piece. Writing can take on a formal or informal tone.
To learn more about tone
https://brainly.com/question/12176973
#SPJ4
A meteorite is found to contain two isotopes of element x, x-12, and x-14. Experimental analysis determined 95% of the element is isotope x-12, whereas 5% of the element is isotope x-14. What is the average atomic mass of element x?.
Considering the definition isotopes and atomic mass of an element, the average atomic mass of element x is 12.1
Definition of isotopeThe same chemical element can have the same atomic numbers, but the number of neutrons is different. These atoms are called isotopes of the element.
Definition of atomic massThe atomic masses of chemical elements are calculated as the weighted average of the masses of the different isotopes of each element, taking into account the relative abundance of each of them.
Atomic mass of the element in this caseIn this case, you know:
Isotope x-12 is 95% abundant (the atomic mass is 12).Isotope x-14 is 5% abundant (the atomic mass is 14).The average mass of the element x can be calculated as:
average mass of element x=12 amu×0.95 + 14 amu×0.05
average mass of element x= 12.1 amu
Finally, the atomic mass of the element x is 12.1.
Learn more about average atomic mass:
brainly.com/question/4923781
brainly.com/question/1826476
brainly.com/question/15230683
brainly.com/question/7955048
#SPJ1
an 81-kg baseball player slides into second base. the coefficient of kinetic friction between the player and the ground is 0.49. (a) what is the magnitude of the frictional force? (b) if the player comes to rest after 1.6 s, what was his initial velocity?
a) The magnitude of the frictional force= -µ mg = 0.49*81*9.8 = 389 N
b)The player comes to rest after 1.6 s, his initial velocity Vi = 7.68 m/s
Acceleration due to friction = - µ g = - 4.80 m/s^2.
V = V0 + at
V = 0
a = - 4.802 m/s^2
t = 1.6 s
V0 = V - at = 0 + 4.8*1.6 = 7.68 m/s
the acceleration of the player due to frictional force is given as
a = f/m = 388.96 /81 = 4.8 m/s2
final velocity = Vf = 0
time = t = 1.6 sec
using the formula
Vf = Vi + at (Vi = initial velocity)
Vi = Vf - at
Vi = 0 - (-4.8) (1.6) (a = -4.8 since player is slowing down)
Vi = 7.68 m/s
A force known as friction exists between two surfaces that are sliding or attempting to glide over one another. Friction, for instance, makes it challenging to push a book across the floor. The direction in which an object moves or attempts to move is always the direction in which friction operates. When anything moves faster or slower in a straight line, it is said to have been acceleration. Because the direction is constantly changing, even motion on a circle accelerates at a constant pace.
Learn more about friction here:
https://brainly.com/question/28356847
#SPJ4
Which answer best describes "displacement"?
A. Displacement is a vector quality showing total length of an area traveled by a particular object.
B. Displacement is a scalar quantity which accounts for how far away an object is after a period of time has elapsed from its initial starting point.
C. Displacement is a scalar quality showing total length of an area traveled by a particular object.
D. Displacement is neither a vector nor scalar quantity, which accounts for how far away an object is after a period of time has elapsed from its initial starting point.
Answer: The answer is the letter
A
Explanation:
Because displacement Its a vector and the letter A says than displacement is a vector quality showing total length of an area traveled by a particular object.
Answer:
(Question 1) Which answer best describes displacement?
(Answer) Displacement is a vector quality showing total length of an area traveled by a particular object.
(Question 2) Kelley is playing pool and hits the cue into the nine ball, which is directly in the center of the pool table. The nine ball travels a total of 7 meters before stopping, 1 meter to the left of the initial starting point of the nine ball. Which sentence reflects the correct statement regarding distance and displacement when considering the motion of the nine ball?
(Answer) The nine ball traveled a distance of 7 meters and was displaced by 1 meter.
(Question 3) What is velocity?
(Answer) Velocity is a vector quantity that tells the distance an object has traveled over a period of time.
(Question 4) Imagine a time-position graph where the velocity of an object is constant. What will be observed on the graph concerning the slope of the line segment as well as the velocity of the object?
(Answer) The slope of the line is equal to zero and the object will be stationary.
(Question 5) Select the option that best summarizes the reason for the use of position-time graphs when studying physical science.
(Answer) The position-time graphs show the relationship between the position of an object (shown on the y-axis) and the time (shown on the x-axis) to show velocity.
Explanation:
just did the quick check, UwU enjoy
name two powers of the president
Answer:
The President can issue executive orders, which direct executive officers or clarify and further existing laws.
The President also has the power to extend pardons and clemencies for federal crimes.
Explanation:
How far could you speed walk in 90 seconds based on your speed for the 10 meter trail
Answer:
Explanation:
Given,
Time ( t ) = 90 seconds
Distance ( d ) = 10 meter
To find : Speed ( v ) = ?
Formula : -
v = d/t
v = 10/90
v = 1/9 m/s ( meters per second )
Hence,
1/9 m/s is the speed walk in 90 seconds for the 10 meter trail.
a passenger walks along the aisle of a train at a speed of 1.3 m/s. the train moves at a speed of 30.2 m/s with respect to the ground. calculate the relativistic correction to the classical value of the passenger speed with respect to the ground. what is the percentage of this correction?
The parameters of speed are time divided by distance.The most often used unit of speed in daily life is the kilometer per hour (km/h), or miles per hour in the US and the UK. The SI's unit of speed is the metre per second (m/s) (mph).
How are speeds determined?
Speed is calculated as follows: speed = distance * time.Knowing the units for distance and time is necessary to calculate the units for speed.The units will be in metres per second (m/s) in this example since the distance is measured in metres (m) and the time is measured in secondsWe have provided The passengers' speed in relation to the train is 2.30 mph, not 2.30 g.Additionally, the passenger is moving at a speed of 30.2m/s relative to the ground.And at a 28 degree angle to the north-west.Therefore, the cost for us passengers will be 4.5 cost 28 and the I. component will be 30.2 signed 28.Now that we know the train's velocity with respect to the ground, we can calculate the passengers' velocity with respect to the train by subtracting the train's velocity with respect to the ground.We shall rearrange this equation once we have determined a city of trained individuals with regard to the ground.Now, if we just insert all of these variables, the passenger's velocity is equal to 30.2 28° I + 4.5 Cost 28° J minus 2.30 G.And after calculation, this will be equal to 3.97 G -2.30 G less, or -2.11 I.Furthermore, this will result in -2.11 I plus 1.67 G.The equation for training velocity with respect to the ground will now be as follows.The size and direction of the trend's velocity with respect to the ground must be determined.Therefore, the magnitude will be 2.11 sq plus 1.67, square root off.We shall rearrange this equation once we have determined a city of trained individuals with regard to the ground.Now, if we just insert all of these variables, the passenger's velocity is equal to -4.5 9 28° I + 4.5 Cost 28° J minus 2.30 G.Calculating yields a value of 2.69 meters per second, and the direction is equal to 2.11 divided by 1.67, which will result in 51.63 agreement.As a result, the trend's magnitude and direction will be B, 2.69 m/s, and 51.63°, respectively, with regard to the ground.
To learn more about value of speed refer
https://brainly.com/question/14719933
#SPJ4
As a result, the trend's magnitude and direction will be B, 2.69 m/s, and 51.63°, respectively, with regard to the ground.
How are speeds determined?Knowing the units for distance and time is important to determine the units for speed. In this example, the units will be measured in metres per second (m/s), as the distance is measured in metres (m) and the time is measured in seconds.We have said that, rather than 2.30 g, the passengers' speed in respect to the train is 2.30 mph.In addition, the passenger is traveling at a relative speed of 30.2 m/s to the ground.Additionally, at a 28-degree northwestern angle.As a result, our guests will pay 4.5 cost 28 and the I. component will be signed at 30.2 and be.To learn more about value of speed refer
brainly.com/question/14719933
#SPJ4
a thin, horizontal, 10-cm-diameter copper plate is charged to 3.5 nc. if the electrons are uniformly distributed on the surface, what are the strength and direction of the electric field
While negative point charges always move in the direction of the opposing electric field, positive point charges always move in the other direction. An electric field is a vector quantity. They cannot be added directly, but they can be vectorially inserted.
What are the electric field's strength and direction?A physical field called an electric field surrounds electrically charged particles and attracts or repels all other charged particles nearby. It can also refer to the physical field surrounding a system of charged particles.
While negative point charges always move in the direction of the opposing electric field, positive point charges always move in the other direction. An electric field is a vector quantity.
Learn more about Electric field here:
brainly.com/question/8971780
#SPJ1