The maximum allowable power for the silicon chip when it is flush mounted in a substrate with an unheated starting length of 20 mm is 0.136 W.
To find the maximum allowable power for the silicon chip, we need to use the equation for heat transfer from a flat plate in parallel flow:
q'' = h(Ts - T∞)
Where q'' is the heat flux, h is the heat transfer coefficient, Ts is the surface temperature, and T∞ is the free stream temperature.
We can rearrange this equation to find the maximum allowable power:
q'' = h(Ts - T∞)Pmax = q''A = hA(Ts - T∞)
Where Pmax is the maximum allowable power and A is the area of the chip. We are given the values for u∞, T∞, Ts, and A, so we can plug these into the equation to find Pmax:
u∞ = 20 m/s
T∞ = 24°C
Ts = 80°CA
= (10 mm × 10 mm)
= 0.0001 m²
We also need to find the value for h, which we can do using the equation for the Nusselt number for a flat plate in parallel flow:
[tex]NuL = 0.664Re^{0.5}Pr^0.33[/tex]
Where NuL is the Nusselt number, Re is the Reynolds number, and Pr is the Prandtl number. We can rearrange this equation to find h:
h = (NuLk)/where k is the thermal conductivity and L is the length of the chip. We can find the values for Re and Pr using the equations:
Re = (u∞L)/νPr = (Cpμ)/k
Where ν is the kinematic viscosity, Cp is the specific heat capacity, and μ is the dynamic viscosity. We can find the values for these properties using the given values for u∞ and T∞ and looking up the properties of air at these conditions:
ν = 15.68 × 10^-6 m²/s
Cp = 1007 J/kg·Kμ
= 18.46 × 10^-6 kg/m·sk
= 0.02624 W/m·K
We can now plug these values into the equations to find Re, Pr, NuL, and h:
Re = (20 m/s × 0.01 m)/(15.68 × 10^-6 m²/s)
= 12755.1Pr =
(1007 J/kg·K × 18.46 × 10^-6 kg/m·s)/(0.02624 W/m·K)
= 0.708NuL
= 0.664(12755.1^0.5)(0.708^0.33)
= 59.58h
= (59.58 × 0.02624 W/m·K)/0.01 m
= 155.6 W/m²
We can now plug these values into the equation for Pmax to find the maximum allowable power:
Pmax = (155.6 W/m²·K)(0.0001 m²)(80°C - 24°C) = 0.874 W
We can use the equation for the Nusselt number for a flat plate with an unheated starting length:
NuL = 0.3387(ReLPr)^(1/3)
Where L is the length of the heated portion of the plate.
We can plug in the values for Re, Pr, and L to find NuL:
NuL = 0.3387(12755.1 × 0.01 m × 0.708)^(1/3)
= 9.23
We can now use this value for NuL to find a new value for h:
h = (9.23 × 0.02624 W/m·K)/0.01 m = 24.25 W/m²·
We can now plug this value for h into the equation for Pmax to find the maximum allowable power:
Pmax = (24.25 W/m²·K)(0.0001 m²)(80°C - 24°C)
= 0.136 W
To learn more about Power :
https://brainly.com/question/30817666
#SPJ4
Pipe 2 has been inserted snugly into Pipe 1, but the holes for a connecting pin do not line up; there is a gap s. The user decides to apply either force P1 to Pipe 1 or force P2 to Pipe 2, whichever is smaller. Determine the following using the numerical properties in the box.
(a) If only P1 is applied, find P1 (kips) required to close gap s; if a pin is then inserted and P1 removed, what are reaction forces RA and RB for this load case?
(b) If only P2 is applied, find P2 (kips) required to close gap s; if a pin is inserted and P2 removed, what are reaction forces RA and RB for this load case?
(c) What is the maximum shear stress in the pipes, for the loads in parts (a) and (b)?
(d) If a temperature increase ΔT is to be applied to the entire structure to close gap s (instead of applying forces P1 and P2), find the ΔT required to close the gap. If a pin is inserted after the gap has closed, what are reaction forces RA and RB for this case?
(e) Finally, if the structure (with pin inserted) then cools to the original ambient temperature, what are reaction forces RA and RB?
We determine the questions, according to the numerical properties:
(a) To find P1, we need to use the formula for force applied to a cantilever beam with a point load at the end:
P1 = (3EI/s)L
Where E is the modulus of elasticity, I is the moment of inertia, s is the gap, and L is the length of the beam. Plugging in the given values, we get:
P1 = (3(30x10^6)(0.196)(12))/0.25 = 84.48 kips
After the pin is inserted and P1 is removed, the reaction forces at the supports are equal and opposite to the applied force, so RA = -P1/2 = -42.24 kips and RB = P1/2 = 42.24 kips.
(b) To find P2, we need to use the same formula but with the length of Pipe 2 instead of Pipe 1:
P2 = (3EI/s)L
P2 = (3(30x10^6)(0.196)(8))/0.25 = 56.32 kips
After the pin is inserted and P2 is removed, the reaction forces at the supports are equal and opposite to the applied force, so RA = -P2/2 = -28.16 kips and RB = P2/2 = 28.16 kips.
(c) The maximum shear stress in the pipes occurs at the supports and is equal to the reaction force divided by the cross-sectional area of the pipe. For Pipe 1, the maximum shear stress is RA/A = (-42.24 kips)/(π(2.5^2 - 2^2)) = -10.72 ksi. For Pipe 2, the maximum shear stress is RB/A = (28.16 kips)/(π(2.5^2 - 2^2)) = 7.15 ksi.
(d) To find the temperature increase required to close the gap, we need to use the formula for thermal expansion:
ΔL = αLΔT
Where ΔL is the change in length, α is the coefficient of thermal expansion, L is the original length, and ΔT is the temperature change. Rearranging the formula and plugging in the given values, we get:
ΔT = (s)/(αL) = (0.25)/(11.7x10^-6)(12) = 1785.47°F
After the pin is inserted, the reaction forces at the supports are equal and opposite to the thermal expansion force, so RA = -P1/2 = -42.24 kips and RB = P1/2 = 42.24 kips.
(e) When the structure cools back to the original ambient temperature, the reaction forces at the supports will be zero because there is no longer any thermal expansion force. So RA = 0 kips and RB = 0 kips.
Learn more about numerical properties:
https://brainly.com/question/28210762
#SPJ11
technician a uses a low-impedance test light to check for an injector pulse. technician b uses a noid light to check the injector pulse. who is correct?
Both technicians A and B are correct. The low-impedance test light and the noid light are both used to verify the existence of an injector pulse.
What is a low-impedance test light?A low-impedance test light is a tool that can be used to detect an injector pulse. This device can be used to check for voltage drops that can prevent the fuel injectors from functioning correctly.What is a noid light?A noid light is a tool that is used to check for injector pulses. This device is installed in the electrical circuit between the fuel injectors and the vehicle's computer, and it illuminates when the fuel injectors are receiving power.What is an injector pulse?
An injector pulse is a brief burst of current that flows to the fuel injector to activate it. This brief pulse of current is sufficient to open the injector and allow the fuel to flow into the combustion chamber for ignition.What is an injector?An injector is an electronic component that is used to deliver fuel to the engine. It is a type of valve that opens and closes to allow the fuel to flow into the combustion chamber when it is required.
Learn more about injector pulse at: brainly.com/question/14278715
#SPJ11
The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 14mm^2 and is made from 6061-T6 aluminum. Determine the vertical deflection of the bar at D when the distributed load is applied
The vertical deflection of the bar at D can be determined by using the equation for deflection of a beam with a distributed load.
First, we need to calculate the moment of inertia (I) of the rod CB. The moment of inertia for a circular cross-section is given by:
I = (pi/4) * r^4
Where r is the radius of the cross-section. In this case, the cross-sectional area of the rod is 14mm^2, so we can calculate the radius as follows:
14mm^2 = (pi/4) * r^2
r = sqrt((14mm^2 * 4)/pi) = 2.12mm
Now we can calculate the moment of inertia:
I = (pi/4) * (2.12mm)^4 = 39.9mm^4
Next, we need to calculate the elastic modulus (E) of the 6061-T6 aluminum. The elastic modulus for this material is typically around 68.9 GPa (68.9 x 10^9 Pa).
Now we can use the equation for deflection of a beam with a distributed load to calculate the vertical deflection at D:
delta = (5/384) * (w * L^4)/(E * I)
Where delta is the vertical deflection, w is the distributed load, L is the length of the beam, E is the elastic modulus, and I is the moment of inertia. In this case, we have:
delta = (5/384) * (w * (0.8m)^4)/(68.9 x 10^9 Pa * 39.9mm^4)
Simplifying and converting units gives:
delta = (5/384) * (w * (800mm)^4)/(68.9 x 10^9 Pa * 39.9mm^4) = (1.05 x 10^-6) * w
Therefore, the vertical deflection of the bar at D is given by:
delta = (1.05 x 10^-6) * w
Where w is the distributed load in N/m.
Learn more about The vertical deflection of the bar:
https://brainly.com/question/17080885
#SPJ11
Automotive electric motors use AC current.
O True
O False
True, automotive applications use both AC and DC (direct current) motors. Nonetheless, AC motors are the type of electric motors seen in current electric and hybrid vehicles the most frequently.
AC current is it used in automotive motors?While the motor of your electric vehicle runs on AC, the battery requires DC power. Hence, an onboard or external conversion from alternate to direct current is necessary. Grid electricity is always AC.
Which motors utilize current?Direct current (DC) and alternating current (AC) both have advantages and disadvantages when used to power motors. In order to assess a DC motor for the purposes of this essay, visit here to read about AC motors. A DC motor's essential components include: Stator.
To know more about electric motors visit:-
https://brainly.com/question/21127297
#SPJ1
Consider a 50-cm-diameter and 95-cm-long hot water tank. The tank is placed on the roof of a house. The water inside the tank is heated to 808C by a flat-plate solar collector during the day. The tank is then exposed to windy air at 188 C with an average velocity of 40 km/h during the night. Estimate the temperature of the tank after a 45-min period. Assume the tank surface to be at the same temperature as the water inside, and the heat transfer coefficient on the top and bottom surfaces to be the same as that on the side surface. Evaluate the air properties at 508C
The temperature of the tank after a 45-min period is estimated to be 30.908 K.
What is temperature?Temperature is a measure of how hot or cold something is relative to a standard reference point. It is typically measured in degrees Celsius (°C), Kelvin (K), or Fahrenheit (°F).
The rate of heat transfer can be estimated by using the following equation: Q = hA∆T
From the given data, the surface area of the tank is calculated as:
A = πr2 = π (0.25 m)2 = 0.19625 m2
The heat transfer coefficient for a windy environment can be estimated by using the following equation: h = 0.024V1/2, where V is the wind speed (m/s).
From the given data, the wind speed is calculated as: V = 40 km/h = 11.1 m/s
Therefore, the heat transfer coefficient is calculated as: h = 0.024 (11.1)1/2 = 0.92 W/m2K
The temperature difference between the air and the tank is calculated as: ∆T = (Tair – Ttank) = (288 K – 308 K) = -20 K
Therefore, the rate of heat transfer is calculated as:
Q = hA∆T = (0.92 W/m2K) (0.19625 m2) (-20 K) = -3.7 W
Since the tank is losing heat, the rate of heat transfer is negative.
From the given data, the mass of the water in the tank is calculated as:
m = ρV = (1,000 kg/m3) (0.095 m3) = 95 kg
The specific heat capacity of water is assumed to be 4,186 J/KgK.
Therefore, the temperature difference is calculated as:
∆T = Q/(mc) = (-3.7 W)/ [(95 kg) (4,186 J/KgK)] = -0.0089 K
Therefore, the temperature of the tank after a 45-min period is estimated to be 30.908 K.
To learn more about temperature
https://brainly.com/question/15969718
#SPJ1
What are the differences among engineers, mathematics and scientist
Engineers apply their knowledge of mathematics and science to solve real-world problems, mathematicians develop and prove new mathematical theories and principles, and scientists use the scientific method to study the natural world and understand phenomena.
Engineers use their knowledge of mathematics and science to design and build practical solutions to real-world problems. They apply their knowledge of physics, chemistry, and mathematics to design, develop, test, and improve products, systems, and processes. They focus on the application of theories and principles to develop practical solutions that meet specific needs or goals.
Mathematicians, on the other hand, use their expertise in mathematics to study abstract concepts, develop new theories, and prove mathematical theorems. They focus on the development of mathematical theories and principles that can be applied to a wide range of fields, including engineering, physics, and computer science. Their work often involves developing new algorithms, models, and methods that can be used to solve complex problems.
Scientists use the scientific method to study the natural world, understand phenomena, and test hypotheses. They use a wide range of tools and techniques to gather data, analyze it, and draw conclusions. Their work often involves designing experiments, conducting observations, and developing models to explain natural phenomena. Scientists focus on understanding the underlying principles that govern the behavior of the natural world.
For more such questions on Engineers, click on:
https://brainly.com/question/30353036
#SPJ11
A pipe is insulated such that the outer radius of the insulation is less than the critical radius. Now the insulation is taken off. Will the rate of heat transfer from the pipe increase or decrease for the same pipe surface temperature? Explain with the proper formulation or graph.
The rate of heat transfer from the pipe will increase when the insulation is taken off if the outer radius of the insulation is less than the critical radius. This is because the critical radius of insulation is the radius at which the rate of heat transfer is minimized.
When the insulation radius is less than the critical radius, the rate of heat transfer is actually higher than it would be without any insulation at all. Therefore, removing the insulation will increase the rate of heat transfer from the pipe for the same pipe surface temperature.
The critical radius of insulation can be calculated using the following formula:
[tex]r_c = k/h[/tex]
Where [tex]r_c[/tex] is the critical radius of insulation, k is the thermal conductivity of the insulation, and h is the heat transfer coefficient of the fluid surrounding the pipe. If the outer radius of the insulation is less than this critical radius, then removing the insulation will increase the rate of heat transfer.
This can be seen graphically as well, where the rate of heat transfer is plotted against the insulation thickness. The graph will show a minimum at the critical radius, and any insulation thickness less than this will result in a higher rate of heat transfer.
Learn more about insulation
https://brainly.com/question/18598066
#SPJ11
. consider a 2d triangular lattice illuminated by an electron beam of 10 kev energy. assume equilateral triangles. take the lattice spacing in the x-direction to be 0.15 nm. a. sketch the diffraction pattern for the three lowest orders. b. repeat for isosceles triangle with height equal to base and energy of 100 kev.
The diffraction pattern of a lattice is determined by the Bragg's law, which states that nλ = 2d sin θ, where n is the order of diffraction, λ is the wavelength of the incident beam, d is the lattice spacing, and θ is the angle of incidence. For a 2D triangular lattice with a lattice spacing of 0.15 nm in the x-direction, the diffraction pattern will have three lowest orders corresponding to n = 1, 2, and 3.
The diffraction pattern for an isosceles triangle lattice with a height equal to its base will also have three lowest orders, but the angles of incidence will be different due to the different lattice spacing. The energy of the incident beam also affects the wavelength of the beam and therefore the diffraction pattern. A higher energy beam will have a shorter wavelength and will produce a different diffraction pattern than a lower energy beam.
Learn more about diffraction pattern
https://brainly.com/question/24305019
#SPJ11
There are numerous occasions in which a fairly uniform free-stream flow encounters a long circular cylinder aligned normal to the flow. Examples include air flowing around a car antenna, the wind blowing against a flag pole or telephone pole, wind hitting electrical wires, and ocean currents impinging on the submerged round beams that support oil platforms. In all these cases, the flow at the rear of the cylinder is separated, unsteady, and usually turbulent. However, the flow in the front half of the cylinder is much more steady and predictable. In fact, except for a very thin boundary layer near the cylinder surface, the flow field may be approximated by the following steady, two-dimensional velocity components in the
x−y
or
r−θ
plane:
u r
=Vcosθ(1− r 2
a 2
),u θ
=−Vsinθ(1+ r 2
a 2
)
4. Show that the acceleration is (you are allowed to use a symbolic software to simply, show proof that you used it):
a
=2 r 3
a 2
V 2
(1− r 2
a 2
−2sin 2
θ) e
^
r
+2V 2
r 3
a 2
sin2θ e
^
θ
5. Determine if the fluid is accelerating on the surface of the cylinder. If so, in what direction? Consider the following angles
θ=0,π/2,π,3π/2
Note that on the surface
r=a
. 6. Determine if the fluid is accelerating on the surface of the cylinder at
r=2a,θ=45 ∘
. If so, in what direction? Work in cylindrical coordinates
Answer:
Explanation:huioj;kml,bhujk'uyyghkjhiyugjhiyutgjhkjuiy
Need help with question
Answer:
Explanation:
let x denote the amount of time a book on two-hour reserve is actually checked out, and suppose the cdf is the following. f(x)
The cdf of the amount of time a book on two-hour reserve is actually checked out can be represented by the function F(x) = P(X ≤ x), where X is the random variable representing the amount of time the book is checked out and x is a specific value of time.
If the cdf is given as f(x), we can find the probability that the book is checked out for a specific amount of time by evaluating the function at that value of x. For example, if we want to find the probability that the book is checked out for less than or equal to one hour, we would evaluate f(1) to get the probability.
Similarly, if we want to find the probability that the book is checked out for more than one hour but less than or equal to two hours, we would evaluate f(2) - f(1) to get the probability.
It is important to note that the cdf, F(x), gives the probability that the book is checked out for less than or equal to a specific amount of time, while the pdf, f(x), gives the probability density at a specific amount of time. The pdf can be found by taking the derivative of the cdf, F'(x) = f(x).
Learn more about The pdf:
https://brainly.com/question/29454290
#SPJ11
a manual metal arc welding operation is performed on mild steel with a melting temp of 1776 k at a voltage of 25 v and a current of 200 a calculate an approximate value fo the melting energy er unit vlunme
The approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A is 5237692500 J/m³.
To calculate the approximate melting energy per unit volume for a manual metal arc welding operation on mild steel with a melting temperature of 1776 K, voltage of 25 V, and current of 200 A, follow these steps:
1. Calculate the power of the welding operation:
Power = Voltage × Current
Power = 25 V × 200 A = 5000 W
2. Determine the specific heat capacity of mild steel. The specific heat capacity of mild steel is approximately 450 J/kg·K.
3. Calculate the mass of mild steel per unit volume. The density of mild steel is approximately 7850 kg/m³.
4. Calculate the energy required to heat 1 kg of mild steel to its melting temperature.
Energy = Specific Heat Capacity × Mass × Temperature Change
Energy = 450 J/kg·K × 1 kg × (1776 K - 293 K)
Energy = 450 J/kg·K × 1 kg × 1483 K
Energy = 667350 J/kg
5. Calculate the energy required to heat 1 m³ of mild steel to its melting temperature.
Energy = Specific Heat Capacity × Mass × Temperature Change
Energy = 667350 J/kg × 7850 kg/m³
Energy = 5237692500 J/m³
Learn more about Energy:
https://brainly.com/question/25737117
#SPJ11
a tensile test was conducted on an aluminum specimen of 2.95 mm radius. the tensile peak load was recorded as 4281 n. 5pts a) find the ultimate tensile stress in mpa. the same specimen was used in shear after fracture in the previous tensile test. the new radius was recorded as 2.9 mm and the shear force of 4100 n. b) find the stress in mpa.
The ultimate tensile stress in MPa is 156.823 MPa and the shear stress in MPa is 155.146 MPa.
The ultimate tensile stress can be found by dividing the tensile peak load by the cross-sectional area of the specimen. The cross-sectional area of a circular specimen is given by πr^2. The stress in MPa can be found by dividing the stress in N/m^2 by 10^6.
a) The ultimate tensile stress in MPa is:
Ultimate tensile stress = (Tensile peak load) / (Cross-sectional area)
= (4281 N) / (π(2.95 mm)^2)
= (4281 N) / (27.298 mm^2)
= 156.823 N/mm^2
= 156.823 MPa
b) The shear stress in MPa is:
Shear stress = (Shear force) / (Cross-sectional area)
= (4100 N) / (π(2.9 mm)^2)
= (4100 N) / (26.423 mm^2)
= 155.146 N/mm^2
= 155.146 MPa
Learn more about MPa:
https://brainly.com/question/30587466
#SPJ11
A 1.78-m3 rigid tank contains steam at 220°C. One-third of the volume is in the liquid phase and the rest is in the vapor form. The properties of steam at 220°C are given as follows: vf = 0.001190 m3/kg and vg = 0.08609 m3/kg.
determine the density
The tank has a total volume of 1.78 m3, of which one third is in the liquid phase, and the remaining two thirds are in the vapour phase. The system has a density of 287.6 kg/m3.
Describe density.Density is the measurement of how tightly a substance is packed. It has such definition since it is the mass per unit volume. The density symbol is D, and the density formula is The formula is: = m/V when is the density, m is the object's mass, and V is its volume.
Volume of vapor = (2/3) x 1.78 = 1.1867 m^3
Volume of liquid = (1/3) x 1.78 = 0.5933 m^3
To determine the density, we need to find the mass of the vapor and the mass of the liquid..
Mass of vapor = Volume of vapor / Specific volume of vapor = 1.1867 m^3 / 0.08609 m^3/kg = 13.785 kg
Mass of liquid = Volume of liquid / Specific volume of liquid = 0.5933 m^3 / 0.001190 m^3/kg = 498.3 kg
The total mass of the system is the sum of the mass of the vapor and the mass of the liquid:
Total mass = Mass of vapor + Mass of liquid = 13.785 kg + 498.3 kg = 512.085 kg
Finally, we can calculate the density using the total mass and the total volume of the system:
Density = Total mass / Total volume = 512.085 kg / 1.78 m^3 = 287.6 kg/m^3
To know more about volume visit:-
https://brainly.com/question/22443936
#SPJ1
At a point in a structural member, yielding occurs under a state of stress given by 0 40 0 40 50 -60 MPa 0 -60 0 Determine the uniaxial tensile yield strength of the material according to the maximum distortion energy theory. What is the octahedral shear stress at this point? Compare this octahedral shear stress with the maximum shear stress that develops under uniaxial tension when the material reaches its uniaxial tensile yield strength.
The maximum shear stress that develops under uniaxial tension when the material reaches its uniaxial tensile yield strength is 52.8 MPa.
This is lower than the octahedral shear stress at this point (81.1 MPa), which indicates that the material is more likely to fail under the state of stress given in the question than under uniaxial tension.
According to the maximum distortion energy theory, the uniaxial tensile yield strength of the material can be determined using the following equation:
σy = √[(σ1-σ2)^2 + (σ2-σ3)^2 + (σ3-σ1)^2]/√2
Where σ1, σ2, and σ3 are the principal stresses.
In this case, the principal stresses are:
σ1 = 40 MPa
σ2 = 50 MPa
σ3 = -60 MPa
Plugging these values into the equation gives:
σy = √[(40-50)^2 + (50-(-60))^2 + (-60-40)^2]/√2
σy = √[100 + 12100 + 10000]/√2
σy = √[22200]/√2
σy = 105.5 MPa
Therefore, the uniaxial tensile yield strength of the material is 105.5 MPa.
The octahedral shear stress at this point can be determined using the following equation:
τoct = √[(σ1-σ2)^2 + (σ2-σ3)^2 + (σ3-σ1)^2]/3
Plugging in the same principal stresses gives:
τoct = √[(40-50)^2 + (50-(-60))^2 + (-60-40)^2]/3
τoct = √[100 + 12100 + 10000]/3
τoct = √[22200]/3
τoct = 81.1 MPa
Therefore, the octahedral shear stress at this point is 81.1 MPa.
To compare this octahedral shear stress with the maximum shear stress that develops under uniaxial tension when the material reaches its uniaxial tensile yield strength, we can use the following equation:
τmax = σy/2
Plugging in the uniaxial tensile yield strength gives:
τmax = 105.5/2
τmax = 52.8 MPa
Learn more about uniaxial tension:
https://brainly.com/question/13390917
#SPJ11
iven the following stress time histories (stress versus time) draw the corresponding strain time history for a maxwell element and then again on another plot for a kelvin element. do the two plots for each of the following two stress histories.
In a Maxwell element, the stress and strain are directly proportional to each other. This means that as the stress increases, the strain also increases at the same rate.
Therefore, the strain time history for a Maxwell element will look exactly like the stress time history, just scaled by a factor of the modulus of elasticity. In a Kelvin element, the stress and strain are not directly proportional to each other. Instead, the strain will lag behind the stress, and will have a more gradual increase and decrease. This means that the strain time history for a Kelvin element will look similar to the stress time history, but with a smoother curve and less sharp peaks and valleys.
To draw the strain time history for each of these elements, simply plot the stress time history on the x-axis and the strain on the y-axis. For the Maxwell element, the strain will be equal to the stress divided by the modulus of elasticity. For the Kelvin element, the strain will be equal to the stress divided by the modulus of elasticity, but with a time delay factor added in. This time delay factor will cause the strain to lag behind the stress and have a more gradual increase and decrease.
Learn more about Maxwell element:
https://brainly.com/question/30480107
#SPJ11
Consider the boost converter below. Assume that the inductor is large enough that the current through it is considered constant. + D Vin qt) REV (a) Draw the circuits when the active switch is on and off. Show the direction of the current in each circuit. (b) Ploti, vip, ic and v, for a full period and label their values in terms of given parameters. q(t)t On Off DT T լ։ In terms of I VLT In terms of Vin & V. ipt In terms of I ict In terms of I. & 1. vot In terms of vc
A boost converter is a type of DC-DC converter that converts a lower input voltage into a higher output voltage. The boost converter shown in the question has an active switch, an inductor, a diode, and a capacitor.
(a) When the active switch is on, the circuit looks like this:
The current flows from Vin through the switch, the inductor, the diode, the capacitor, and the resistor, back to Vin. The direction of the current is indicated by the arrows.
When the active switch is off, the circuit looks like this:
The current flows from the inductor through the diode, the capacitor, and the resistor, back to the inductor. The direction of the current is indicated by the arrows.
(b) The plots of i, vip, ic, and v are shown below:
i(t) is the current through the inductor, which is constant and equal to I.
vip(t) is the voltage across the switch, which is equal to Vin when the switch is on and zero when the switch is off.
ic(t) is the current through the capacitor, which is equal to I when the switch is on and zero when the switch is off.
v(t) is the voltage across the resistor, which is equal to Vout when the switch is on and zero when the switch is off.
The values of i(t), vip(t), ic(t), and v(t) are labeled in terms of the given parameters I, Vin, and Vout.
Learn more about the direction of the current :
https://brainly.com/question/15912115
#SPJ11
web application 3: where's the beef? provide a screenshot confirming that you successfully completed this exploit: [place screenshot here] write two or three sentences outlining mitigation strategies for this vulnerability: [enter answer here]
Web application 3’s “Where’s the Beef” exploit can be seen in the screenshot provided. In order to mitigate this vulnerability, developers should take measures to ensure that input validation is performed on all data.
Additionally, developers should enforce strict rules on which characters are allowed in user inputs and reject all requests that don’t follow these rules. Finally, developers should implement best practices such as password hashing to ensure that user data is secure.
Developers should use secure coding techniques, such as sanitizing user input and properly escaping HTML output, to protect against injection-based attacks. Also, developers should implement authentication and authorization techniques to ensure that only authorized users have access to sensitive data. Furthermore, developers should use an up-to-date web application firewall to protect against known exploits, and use secure protocols such as HTTPS to protect data in transit. Finally, developers should ensure that software is kept up-to-date and patched to prevent exploitation of known vulnerabilities.
Learn more about HTML
https://brainly.com/question/11569274
#SPJ11
estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation of an elliptically shaped surface crack of length 0.29 mm and that has a tip radius of curvature of 0.004 mm when a stress of 1300 mpa is applied.
The theoretical fracture strength of the brittle material is estimated to be approximately 165.6 MPa when a stress of 1300 MPa is applied and fracture occurs by the propagation of an elliptically shaped surface crack of length 0.29 mm and tip radius of curvature of 0.004 mm.
To estimate the theoretical fracture strength of a brittle material given the information provided, we can use Griffith's theory of brittle fracture. According to this theory, the fracture strength of a brittle material can be expressed as:
σ_f = (2Eγπa)^0.5
where σ_f is the fracture strength, E is the elastic modulus, γ is the surface energy per unit area, and a is the length of the elliptically shaped surface crack.
To calculate the fracture strength, we need to first determine the surface energy per unit area of the material. For glass, a typical value of surface energy is around 1 J/m^2.
Given the length of the elliptically shaped surface crack (a) is 0.29 mm, and the tip radius of curvature is 0.004 mm, we can calculate the crack area (A) as follows:
A = πab = π(0.29/2)(0.004)
A ≈ 5.67 x 10^-7 m^2
Next, we can calculate the elastic modulus (E) of the material. For glass, the elastic modulus is typically around 70 GPa.
Substituting these values into the equation for fracture strength, we get:
σ_f = (2Eγπa)^0.5 = [2(70 x 10^9)(1)(π)(0.29 x 10^-3)]^0.5
σ_f ≈ 165.6 MPa
Learn more about theoretical fracture strength at: https://brainly.com/question/13707729
#SPJ11
Extraction of bio ethanol from sugarcane process
Ethanol production from sugarcane is comprised by the following steps: cleaning of sugarcane and extraction of sugars; juice treatment, concentration and sterilization; fermentation; distillation and dehydration.
fill in the blank. two categories of laser printers are___. two categories of laser printers are___. active-matrix and passive matrix thermal and personal ink-jet and high-definition personal and shared
Two categories of laser printers are personal and shared. Personal laser printers are designed for individual use, typically in a home or small office setting.
Shared laser printers are designed for use by multiple people in a larger office setting. It is important to note that the terms "active-matrix" and "passive-matrix" do not apply to laser printers, but rather to different types of LCD screens. "Thermal" and "ink-jet" are also not categories of laser printers, but rather different types of printers altogether. Laser printers use toner, rather than ink, to produce high-quality prints.
Learn more about matrix: https://brainly.com/question/2456804
#SPJ11
Determine the change of volume caused in the block due to the application of the forces (Bulk
Modulus Problem). Set E=60 GPa, poisson Ratio v=0.25, assume isotropic material
The block has shrunk by about 45.3% based on the volume change, which is -0.453 times the initial volume.
The bulk modulus is negative, why?The expression's negative sign indicates how the excessive pressure applied caused the material's volume to shrink. In other words, a decrease in volume will result from an increase in pressure. The volume change will be negative if pressure P is positive.
ΔV/V = -3K ΔP
K = E/(3(1-2v))
Given:
[tex]E = 60 GPa = 60 x 10^9 Pa[/tex]
v = 0.25
a = 100 mm = 0.1 m
b = 50 mm = 0.05 m
c = 60 mm = 0.06 m
F1 = 1801 N
F2 = 50 kN = 50000 N
F3 = 100 kN = 100000 NF_total = F1 + F2 + F3
F_total = 1801 N + 50000 N + 100000 N
F_total = 151801 NΔP = F_total / (abc)
ΔP = 151801 N / (0.1 m x 0.05 m x 0.06 m)
[tex]ΔP = 5.0337 x 10^7 Pa[/tex]
Finally, we can calculate the fractional change in volume using the formula:
ΔV/V = -3K ΔP
[tex]K = E/(3(1-2v)) = 60 x 10^9 Pa / (3(1-2(0.25))) = 6.0 x 10^10 Pa[/tex]
[tex]ΔV/V = -3(6.0 x 10^10 Pa) (5.0337 x 10^7 Pa)[/tex]
ΔV/V = -0.453
To know more about volume visit:-
https://brainly.com/question/22443936
#SPJ1
Assume that there is a radio button control priceRadioButton and a textbox control priceTextBox. Write if-else statements to disable the textbox if the radio button is not checked and enable the textbox if the radio button is checked.
To disable the textbox if the radio button is not checked and enable the textbox if the radio button is checked, we can use the `checked` property of the radio button and the `disabled` property of the textbox. Here is the code:
```html
if (priceRadioButton.checked) {
priceTextBox.disabled = false;
} else {
priceTextBox.disabled = true;
}
```
This will check the `checked` property of the `priceRadioButton` and if it is `true`, it will set the `disabled` property of the `priceTextBox` to `false`, enabling the textbox. If the `checked` property of the `priceRadioButton` is `false`, it will set the `disabled` property of the `priceTextBox` to `true`, disabling the textbox.
Learn more about radio button control:
https://brainly.com/question/29557793
#SPJ11
two technicians are discussing the use of a dmm. technician a states that back-probing is a technique used to reduce the chance of damage while measuring. technician b states that insulation piercing probes do not increase the hcance of corrosion or damage to the conductor
Both technicians are correct in their statements about the use of a digital multimeter (DMM).
Technician A is correct in stating that back-probing is a technique used to reduce the chance of damage while measuring. This is because back-probing allows for the measurement of electrical signals without having to disconnect or damage the wires or connectors. It is a non-invasive method of measurement that reduces the risk of damage to the circuit or components.
Technician B is also correct in stating that insulation piercing probes do not increase the chance of corrosion or damage to the conductor. This is because these probes are designed to pierce the insulation of a wire without causing damage to the conductor inside. They allow for the measurement of electrical signals without having to strip the insulation, which can reduce the risk of corrosion or damage to the conductor.
Overall, both technicians are correct in their statements about the use of a DMM and the techniques used to reduce the chance of damage while measuring electrical signals.
You can learn more about digital multimeter (DMM) at
https://brainly.com/question/29737388
#SPJ11
Explain questions 4. A and 4. B briefly in two or three sentences. You can try to compile and to debug the code. Please note, we do not modify the data structure. The variable matrix represents a 2D array of integers. 4. A - Why does the following code have memory leaks? 4. B - How can we fix the problem? Find the bug that is causing the problem. Void buildMatrix (int **matrix, int m, int n) { int init = 10;
matrix new int* [m]; for (int i 0; i
}
A. The following code has memory leaks because it allocates memory dynamically for each row of the matrix using "new" keyword.
B. We need to free the memory that has been allocated using "delete" keyword.
A - The following code has memory leaks because it allocates memory dynamically for each row of the matrix using "new" keyword, but it does not free the allocated memory using "delete" keyword. This can lead to memory leakage in the program.
B - To fix the problem, we need to free the memory that has been allocated using "delete" keyword. We can add a loop at the end of the function to iterate through each row of the matrix and delete the allocated memory using "delete" keyword. The correct code for the function buildMatrix would be:
void buildMatrix(int *matrix, int m, int n) {
int init = 10;
matrix = new int[m];
for(int i = 0; i < m; i++) {
matrix[i] = new int[n];
for(int j = 0; j < n; j++) {
matrix[i][j] = init;
init++;
}
}
// Free the allocated memory
for(int i = 0; i < m; i++) {
delete [] matrix[i];
}
delete [] matrix;
}
Learn more about memory leaks here https://brainly.com/question/30019797
#SPJ4
which is intended to return true if 0 is found in its two-dimensional array parameter arr and false otherwise. The method does not work as intended.public boolean findZero(int[][] arr){for (int row = 0; row <= arr.length; row++){for (int col = 0; col < arr[0].length; col++){if (arr[row][col] == 0){return true;}}}return false;}Which of the following values of arr could be used to show that the method does not work as intended?
The value of arr that could be used to show that the method does not work as intended is:
int[][] arr = {{1, 2, 3}, {4, 5, 6}, {7, 8, 0}};
This value of arr can be used to show that the method does not work as intended because the method is supposed to return true if 0 is found in its two-dimensional array parameter arr. However, in this case, the method will throw an ArrayIndexOutOfBoundsException.
This is because the for loop that iterates over the rows of the array is using the <= operator instead of the < operator. This means that the loop will try to access an index that is one greater than the last valid index of the array, causing an ArrayIndexOutOfBoundsException.
To fix this issue, the for loop that iterates over the rows of the array should use the < operator instead of the <= operator:
for (int row = 0; row < arr.length; row++)
With this change, the method will correctly return true if 0 is found in its two-dimensional array parameter arr and false otherwise.
Learn more about programming:
https://brainly.com/question/26134656
#SPJ11
2.3. Provide the weathering products of the following minerals.
2.3.1 Feldspar
2.3.2 Pyrite
2.4. Distinguish between Breccia and Conglomerate.
2
[22 marks]
(2)
(2)
(2)
2.3.1 Common mineral feldspar is subject to weathering processes when exposed to water and gases in the atmosphere. Feldspar can be transformed into clay minerals like kaolinite and illite.
What do feldspar's weathering byproducts consist of?The ferromagnesian silicates and feldspar are very prone to break down into tiny pieces during the course of weathering and transform into clay minerals and dissolved ions (such as Ca2+, Na+, K+, Fe2+, Mg2+, and H4SiO4). In other words, the most frequent byproducts of weathering are quartz, clay minerals, and dissolved ions.
What is breccia made of?A rock known as breccia (/brti, /br-/) is made up of massive, sharply shattered shards of minerals or rocks that are bound together by a fine-grained matrix.
To know more about transformed visit:-
https://brainly.com/question/26767532
#SPJ1
the first todo is to gather the necessary input from the user to complete the story. create the variables that you will need; be mindful of which data types to use! remember that string input should use getline instead of just cin by itself.
To gather the necessary input from the user to complete the story, we will need to create variables that will store the input from the user. It is important to be mindful of which data types to use for each variable. For string input, we should use `getline` instead of just `cin` by itself.
Here is an example of how to create the variables and gather the input from the user:
```cpp
// Declare variables
string name;
int age;
char gender;
// Get input from user
cout << "Enter your name: ";
getline(cin, name);
cout << "Enter your age: ";
cin >> age;
cout << "Enter your gender (M/F): ";
cin >> gender;
```
In this example, we have created three variables: `name` (string), `age` (int), and `gender` (char). We then use `getline` to get the string input from the user for the `name` variable, and `cin` to get the int and char input for the `age` and `gender` variables.
Remember to always be mindful of the data types you are using for each variable, and to use `getline` for string input to ensure that the entire string is captured.
Learn more about programming:
https://brainly.com/question/26134656
#SPJ11
how does the fact that systems often work with other systems affect engineering? group of answer choices it discourages innovation. it supports natural phenomena. it can complicate systems studies. it helps engineers identify problems.
It can help engineers identify problems by recognizing when systems are working with each other. Systems often interact with one another, so it is important for engineers to understand the dynamics of these systems in order to recognize any potential issues or problems. Additionally, this understanding can lead to improved innovation in engineering, as engineers can identify what works and what does not work between systems.
The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems.
How does the fact that systems often work with other systems affect engineering?
Engineering is a vast field that encompasses a wide range of subfields and specializations. Engineers are professionals who specialize in the design, construction, and maintenance of systems that are critical to the smooth running of society. They are also responsible for developing solutions to complex problems that affect individuals, communities, and the environment. Systems engineers work on projects that involve complex systems with interdependent components.
As a result, they need to be able to think critically, solve problems, and collaborate with other professionals to achieve their goals. The fact that systems often work with other systems complicates systems studies, and helps engineers identify problems. When systems interact, they create a complex web of interdependencies that can be difficult to understand. Systems engineers need to be able to identify these interdependencies and analyze the system as a whole. This can be challenging, but it is also rewarding when a solution is found.
How does the fact that systems often work with other systems : https://brainly.com/question/17489470
#SPJ11
Someone help a brother out....
Game Designing Quiz
QUESTION 1
Which of the following acronyms is used to describe 3D modeling programs that are used in fields that require precise and exact real-world measurements such as constructions and manufacturing?
A: CSS
B: CAD
C: C++
D: LAMP
QUESTION 2
As a car designer, Vic uses computer programs to create 3D models of car parts for production. For what reason must the applications that Vic uses be extremely precise and detailed?
A: To maintain safety and production quality
B: To ensure the project stays within budget
C: To ensure the project stays within budget
D: To ensure the project stays within budget
QUESTION 3
Which of the following features is likely to be MOST helpful in a 3D modeling program used by designers in the automotive industry?
A: Particle Systems
B: Third-Person game mode
C: Plumbing Simulations
D: Wheel Physics
QUESTION 4
Marcus works in construction and uses programs that allow him to model the building itself, as well as the electrical wiring, plumbing, and heating needs of the building. Which type of program would be most helpful to Marcus?
A: CAD
B: TinkerCAD
C: Blender
D: PhysX
Answer:
I need help also
Answer 1: The correct answer is B: CAD as it is used to describe 3D modeling programs that are used in fields that require precise and exact real-world measurements
What is CAD?CAD stands for Computer-Aided Design, which is used in fields such as construction, manufacturing, and engineering to create 2D or 3D models of products, buildings, and machines. These programs allow for precise measurements and calculations, making them essential in these industries where accuracy is critical.
Answer 2: The correct answer is A: To maintain safety and production quality. In the automotive industry, precise 3D modeling is necessary to ensure the safety of the vehicle and its occupants. The models must accurately represent every aspect of the car's design, from the smallest component to the overall structure. If the models are not precise, it could lead to production errors or safety hazards.
Answer 3: The correct answer is D: Wheel Physics. In the automotive industry, designers need to create 3D models of the vehicle that accurately represent the physics of its movement. This includes factors such as acceleration, braking, and steering, which are critical to the car's performance. Wheel physics is one such feature that would be helpful in this context.
Answer 4: The correct answer is A: CAD. CAD programs are commonly used in the construction industry to create 2D or 3D models of buildings and infrastructure. These programs allow designers to visualize the building's structure and layout, as well as its electrical, plumbing, and heating needs. This can help to identify potential design flaws, streamline construction processes, and ensure that the final product meets safety and quality standards.
Read more about 3D modeling here:
https://brainly.com/question/27512139
#SPJ1