a pogo stick rider is traveling at 7.213 meters/second and has a mass of 73.6 kilograms. the following fictitious units and their conversion factors have been provided below. perform the indicated unit conversions and report your answers to the correct number of

The velocity of the center of mass of the skater-snowball system will remain unchanged.

The total momentum of the system is conserved, as there are no external forces acting on the system. The momentum of the snowball is equal and opposite to the momentum of the skater, so the total momentum of the system is zero before and after the snowball is thrown.

Since the total momentum of the system is conserved, the velocity of the center of mass of the system must remain the same. Therefore, the skater will continue to move at a constant velocity in the same direction, and the center of mass of the system will continue to move with the same velocity as the skater.

The snowball will move forward relative to the skater, but the center of mass of the system will remain unaffected.

To know more about center of mass, refer here:
https://brainly.com/question/29576405#
#SPJ11

If you could measure the orbital speeds of particles in an accretion disk around a black hole, you would notice several things. First, you would notice that the speeds of the particles closer to the black hole are much faster than those further away.

This is because the gravitational force of the black hole is stronger closer to it, causing particles to move faster in their orbits.Second, you would notice that there is a "hole" in the accretion disk, where there are no particles orbiting. This is because the gravitational pull of the black hole is so strong that it has consumed all of the particles in that region. This is known as the "innermost stable circular orbit" and is a key feature of black holes.Finally, you would notice that the orbital speeds of particles in the accretion disk are close to the speed of light. This is because the gravitational force of the black hole is so strong that it has warped the fabric of spacetime, causing particles to move at extreme speeds.
Overall, measuring the orbital speeds of particles in an accretion disk around a black hole would provide valuable insights into the nature of black holes and the extreme conditions that exist in their vicinity.

Learn more about orbital here

https://brainly.com/question/26000020

#SPJ11

i) The turning moment is measured in newton-meters (Nm) at 240 Nm.

ii) A 150 N force exerted at hole B, 1.6m above ground, produces the same turning moment as a 300 N force.

i) The turning moment about pivot P can be calculated by multiplying the force applied by the perpendicular distance between the force and the pivot point. In this case, the distance is given as 0.8m.

Turning moment = force x perpendicular distance

Turning moment = 300N x 0.8m

Turning moment = 240 Nm

The unit for turning moment is newton-meters (Nm).

ii) The turning moment is constant, so set the turning moment about pivot P from part (i) equal to the turning moment produced by the force at hole B.

240 Nm = force x 1.6m

force = 240 Nm / 1.6m

force = 150 N

Therefore, a force of 150 N applied at hole B, 1.6m above the ground, would produce the same turning moment as a force of 300 N applied at hole A, 0.8m above the ground.

Find out more on horizontal force here: https://brainly.com/question/12979825

#SPJ1

The distance of the block from its equilibrium position when its speed is half its maximum speed of the block is 0.86A

In a system, the mechanical energy is conserved that is it is neither gained nor lost. Mechanical energy is the sum of kinetic energy and the potential energy of the system.

Thus at the maximum speed, the kinetic energy is highest and the potential energy is null.

E = [tex]\frac{1}{2}mv^2_{max}[/tex]

At amplitude, the potential energy is the maximum, and kinetic energy is zero

E = [tex]\frac{1}{2}kA^2[/tex]

Since mechanical energy is conserved,

[tex]\frac{1}{2}kA^2[/tex] = [tex]\frac{1}{2}mv^2_{max}[/tex]

At a speed that is half of the maximum speed,

E = KE + PE

E = [tex]\frac{1}{8}mv^2_{max}[/tex] + [tex]\frac{1}{2}kx^2[/tex]

[tex]\frac{1}{2}mv^2_{max}[/tex] = [tex]\frac{1}{8}mv^2_{max}[/tex] + [tex]\frac{1}{2}kx^2[/tex]

[tex]\frac{3}{8}mv^2_{max[/tex] = [tex]\frac{1}{2}kx^2[/tex]

[tex]\frac{3}{4}[/tex] * [tex]\frac{1}{2}kA^2[/tex] = [tex]\frac{1}{2}kx^2[/tex]

0.75 [tex]A^2[/tex] = [tex]x^2[/tex]

x = [tex]\sqrt{0.75}[/tex] A ≈ 0.86A

Learn more about Mechanical energy:

https://brainly.com/question/28154924

#SPJ4

The key observation needed to determine whether the compact object is a neutron star or a black hole is the presence or absence of X-ray emission. Neutron stars have strong magnetic fields that can create X-rays, while black holes do not emit X-rays unless they are actively accreting matter from a nearby companion star.

Therefore, if X-ray emission is detected, the compact object is likely a neutron star, whereas the absence of X-ray emission suggests a black hole. To determine whether the compact object is a neutron star or a black hole, the key observation needed is to analyze the object's mass and its gravitational effects on its surroundings. If the compact object has a mass greater than the Tolman-Oppenheimer-Volkoff (TOV) limit (around 2-3 times the mass of the Sun) and exhibits strong gravitational effects, such as bending light or trapping nearby objects, it is likely a black hole. If the object has a lower mass and displays less extreme gravitational effects, it could be a neutron star.

Learn more about neutron here: brainly.com/question/31087562

#SPJ11

The emission of gravitational waves in a binary system of two neutron stars will have several effects on the system:

Orbital decay: The emission of gravitational waves carries away energy and angular momentum from the binary system, causing the two neutron stars to spiral closer together over time. This effect is known as orbital decay, and it results in a gradual decrease in the period of the binary orbit.

Inspiraling: As the two neutron stars spiral closer together due to orbital decay, their orbital velocity will increase, and they will eventually begin to orbit each other at a high enough velocity to cause a significant distortion of spacetime. This effect is known as inspiraling, and it results in an increase in the emission of gravitational waves.

Merger: Eventually, the two neutron stars will spiral close enough together that their mutual gravitational attraction will overcome the repulsive force between their neutron cores, leading to a merger. This merger produces a burst of gravitational waves that can be detected by ground-based gravitational wave observatories.

Overall, the emission of gravitational waves in a binary system of two neutron stars provides a unique and powerful probe of the properties of neutron stars and their gravitational interactions. By observing the properties of the emitted gravitational waves, astronomers can learn about the masses, spins, and radii of the neutron stars, as well as the nature of the strong nuclear force that holds their cores together.

Learn more about Gravitation here:- brainly.com/question/940770

#SPJ11

(a) To determine the force constant (k) of the spring, we will use Hooke's Law, which states that the force exerted by a spring (F) is proportional to the displacement (x) from its equilibrium position:

F = -kx

First, we need to calculate the gravitational force (weight) acting on the 2.40 kg object:

F = mg
F = (2.40 kg)(9.81 m/s²)
F ≈ 23.544 N

Now, we can use Hooke's Law to find the force constant (k):

23.544 N = k(0.0228 m)
k ≈ 1032 N/m

(b) To find the distance the spring stretches with a 1.20 kg object, we'll use the same formula:

F = (1.20 kg)(9.81 m/s²)
F ≈ 11.772 N

Now, rearrange Hooke's Law to solve for x:

x = F/k
x ≈ 11.772 N / 1032 N/m
x ≈ 0.0114 m or 1.14 cm

(c) To calculate the work (W) done by an external agent to stretch the spring 8.70 cm, we'll use the formula for the work done on a spring:

W = (1/2)kx²

First, convert the distance to meters:

x = 8.70 cm = 0.087 m

Now, calculate the work:

W = (1/2)(1032 N/m)(0.087 m)²
W ≈ 3.918 J

To know more about Hooke's Law refer here:

https://brainly.com/question/30379950#

#SPJ11

The work done in lifting the 6.8 N object from the ground to a height of 4 m is 27.2 Joules.

To calculate the work done in lifting a 6.8 N object from the ground to a height of 4 m, we need to use the formula:

work = force x distance x cos(theta)

where force is the weight of the object (6.8 N), distance is the height lifted (4 m), and theta is the angle between the force and the direction of motion (which is 0 degrees in this case since the force is acting vertically upward and the motion is also vertical).

Plugging in the values, we get:

work = 6.8 N x 4 m x cos(0 degrees) = 27.2 J

To know more about work done, here

brainly.com/question/13662169

#SPJ1

A sound wave typically has a much greater wavelength than a light wave. When both waves pass through an open doorway, the sound wave will diffract to a greater extent. This difference in diffraction can be explained by considering the relationship between the wavelength of a wave and the size of the obstacle or opening it encounters.

Diffraction is the bending of waves around obstacles or when passing through openings. The extent of diffraction depends on the size of the obstacle or opening relative to the wavelength of the wave. When the wavelength is larger in comparison to the size of the opening, there is a greater degree of diffraction.

Sound waves are mechanical waves that travel through a medium, such as air, and have wavelengths ranging from around 17 meters (low frequency) to 1.7 centimeters (high frequency). On the other hand, light waves are electromagnetic waves with much shorter wavelengths, typically ranging from around 400 nanometers (violet) to 700 nanometers (red).

Since sound waves have much larger wavelengths than light waves, they will experience greater diffraction when passing through an open doorway. As a result, the sound wave will spread out and bend around the edges of the doorway more than the light wave. This is why you can often hear sounds around corners or through doorways, while light does not bend as noticeably in the same circumstances.

For more such questions on Diffraction.

https://brainly.com/question/12290582#

#SPJ11

The maximum tension in the string is approximately 197.81 Newtons.

To find the maximum tension in the string when a 0.3-kg object is being whirled in a horizontal circle at the end of a 1.5 m long string with 200 revolutions per minute (rpm), follow these steps:

1. Convert revolutions per minute (rpm) to radians per second (rad/s):
200 rpm ×(2π rad / 1 revolution) × (min / 60 s) ≈ 20.94 rad/s

2. Calculate the centripetal acceleration (a_c) using the formula a_c = ω² × r, where ω is the angular velocity in rad/s and r is the radius of the circle:
a_c = (20.94 rad/s)² ×1.5 m ≈ 659.37 m/s^2

3. Calculate the maximum tension (T) in the string using the formula T = m ×a_c, where m is the mass of the object:
T = 0.3 kg × 659.37 m/s² ≈ 197.81 N

So, the maximum tension in the string is approximately 197.81 Newtons.

To learn more about revolutions https://brainly.com/question/7246116

#SPJ11

The Tully-Fisher relation states that the luminosity of a galaxy is directly proportional to its rotational velocity, or more precisely, to its total mass.

The Tully-Fisher relation is an empirical relationship between the luminosity and the rotational velocity of spiral galaxies. It states that the more massive a galaxy is, the faster its stars rotate around the galaxy's center, and the brighter it appears. This relation provides a useful tool for astronomers to estimate the mass of a galaxy based on its luminosity or vice versa. However, the underlying physical mechanism that connects luminosity and mass is still not well understood, and there are ongoing debates about the origin of the Tully-Fisher relation.

Learn more about Tully-Fisher relation  here.

https://brainly.com/question/28216202

#SPJ11

Isaac Newton used a prism to disperse a beam of sunlight into the colors of the rainbow; he then used a second prism to recombine the colors back into white light.

In 1666, Isaac Newton conducted a series of experiments with light using a prism. He found that a beam of sunlight could be separated into its component colors by passing through a prism, a process known as dispersion.

The colors of the rainbow, in order from longest to shortest wavelength, are red, orange, yellow, green, blue, indigo, and violet. Newton named this sequence of colors the spectrum.

Newton also discovered that the colors could be recombined into white light by passing the spectrum through a second prism, a process known as recombination. This experiment demonstrated that white light is actually composed of all the colors in the visible spectrum.

Newton's experiments with light and prisms laid the foundation for the field of optics and contributed to the development of modern theories of light and color. His work showed that white light is not a fundamental entity but is instead composed of different wavelengths of light that can be separated and recombined.

To know more about Isaac Newton, refer here:
https://brainly.com/question/15302749#
#SPJ11

To determine the cart's speed, we can use the position-time graph or the velocity-time graph. Both graphs can be used to determine the speed of the cart, but each graph provides different information about the motion of the cart.

The position-time graph shows the position of the cart at different times. The slope of the position-time graph gives us the velocity of the cart. A positive slope indicates that the cart is moving in the positive direction, and a negative slope indicates that the cart is moving in the negative direction.

Therefore, we can use the position-time graph to determine the cart's speed by calculating the slope of the graph. The speed of the cart is simply the magnitude of the velocity, which is given by the slope of the position-time graph.

On the other hand, the velocity-time graph shows the velocity of the cart at different times. The slope of the velocity-time graph gives us the acceleration of the cart. A positive slope indicates that the cart is accelerating in the positive direction, and a negative slope indicates that the cart is accelerating in the negative direction.

Therefore, we can use the velocity-time graph to determine the cart's speed by calculating the area under the curve of the graph. The speed of the cart is simply the magnitude of the velocity, which is given by the area under the curve of the velocity-time graph.

In summary, both the position-time and velocity-time graphs can be used to determine the cart's speed, but each graph provides different information about the motion of the cart. The position-time graph gives us the velocity, and the velocity-time graph gives us the acceleration.

For more such questions on Position-time and velocity-time graph.

https://brainly.com/question/11290682#

#SPJ11

The radius of gyration determines the point from the center of a flywheel where the mass can be concentrated and be equal to the actual distributed mass. In a rotating object, like a flywheel, the mass is distributed across the entire shape, which affects its rotational inertia.

The radius of gyration is a measure that simplifies this concept by considering an equivalent mass concentrated at a specific distance from the center. This distance is the radius of gyration, which can be calculated using the moment of inertia of the object.

By understanding and optimizing the radius of gyration, engineers can design more efficient and stable flywheels for various applications, such as energy storage and regulation of rotational speed.

To know more about radius of gyration refer here:

https://brainly.com/question/30024312#

#SPJ11

Impedance, Z = √(R²+ (Xl - Xc)²) where Xl = 2πfL and Xc = 1/(2πfC)

(a) To find the maximum current and the phase angle, we need to calculate the impedance first:

Xl = 2πfL = 2π × 50.0 × 0.792 = 99.36 Ω

Xc = 1/(2πfC) = 1/(2π × 50.0 × 44.3 × 10^-6) = 72.06 Ω

Z = √(R² + (Xl - Xc)²) = √(278² + (99.36 - 72.06)²) = 353.3 Ω

φ = arctan((Xl - Xc)/R) = arctan((99.36 - 72.06)/278) = 0.289 rad = 16.6°

Imax = V/Z = 120.0/353.3 = 0.339 A

Therefore, the maximum current is 0.339 A and the phase angle between the current and the source emf is 16.6°.

(b) To find the maximum potential difference across the inductor, we can use the formula:

VL, max = Imax Xl = 0.339 × 99.36 = 33.8 V

The phase angle between this potential difference and the current in the circuit is 90° - φ = 73.4°.

(c) To find the maximum potential difference across the resistor, we can use the formula:

VR, max = Imax R = 0.339 × 278 = 94.0 V

The phase angle between this potential difference and the current in the circuit is 0°.

(d) To find the maximum potential difference across the capacitor, we can use the formula:

VC, max = Imax Xc = 0.339 × 72.06 = 24.4 V

The phase angle between this potential difference and the current in the circuit is -90° - φ = -106.6°.

Impedance is a fundamental concept in physics that describes the resistance of a circuit to the flow of alternating current (AC) or signals. It is represented by the symbol Z and is measured in ohms. Impedance is a combination of resistance, capacitance, and inductance and is affected by the frequency of the AC or signal.

In an AC circuit, the impedance can be broken down into two components: resistance (R) and reactance (X), where X is the sum of the capacitance and inductance. The impedance of a circuit determines how much current flows through it when a voltage is applied, and is a crucial parameter in the design and analysis of electrical circuits. In summary, impedance is a measure of the total opposition to the flow of AC in a circuit and takes into account both the resistance and reactance of the circuit.

To learn more about Impedance visit here:

brainly.com/question/30040649

#SPJ4

The journey between the two stationary stars takes approximately 39.01 years as measured by someone at rest relative to the stars.

To determine how long the journey between two stationary stars takes as measured by someone at rest relative to the stars, we can use the following information:

- The astronaut on the spaceship is moving at 0.927c (c is the speed of light).
- The person at rest relative to the two stars measures the journey to take 20.0 years.

The astronaut's time dilation factor can be calculated using the equation:

Time dilation factor = 1 / √(1 - v²/c²)

Where v is the velocity of the spaceship (0.927c) and c is the speed of light.

First, square the velocity:

(0.927c)² = 0.859² = 0.737169

Now, subtract this value from 1:

1 - 0.737169 = 0.262831

Now, find the square root of the result:

√(0.262831) = 0.512672

The time dilation factor is the reciprocal of this value:

1 / 0.512672 = 1.9505

Now, multiply the astronaut's time measurement (20.0 years) by the time dilation factor:

20.0 years × 1.9505 = 39.01 years

So, by calculating we can say that the journey between the two stationary stars takes 39.01 years (approx.) as measured by someone at rest relative to the stars.

To know more about the  stationary stars refer here :

https://brainly.com/question/31229712#

#SPJ11

The discoverer of X-rays was Roentgen. Option c

Wilhelm Conrad Roentgen, a German physicist, discovered X-rays on November 8, 1895. Roentgen was experimenting with cathode rays in a vacuum tube when he noticed a fluorescent screen in his lab was emitting light despite being far from the cathode ray tube.

He realized that an unknown ray was passing through the tube and causing the screen to glow. Roentgen called this new type of ray "X-ray," and he went on to study and document its properties.

This discovery led to a revolution in medical imaging, allowing doctors to see inside the human body without the need for invasive procedures. Roentgen was awarded the Nobel Prize in Physics in 1901 for his discovery.

To learn more about X-ray, click here:

https://brainly.com/question/23281551

#SPJ11

Your question is: 0.000001 Volt = 1 microvolt So the correct option is D) 1 microvolt

The prefix "micro-" means one millionth, so 1 microvolt (μV) is equal to 0.000001 volts. Therefore, to convert from volts to microvolts, we need to multiply by 1,000,000.

0.000001 volts x 1,000,000 = 1 microvolt

So, 0.000001 volts is equivalent to 1 microvolt.

Alternatively, we can also use the following conversion factor:

1 μV = 0.000001 V

To convert from volts to microvolts, we can multiply by 1,000,000:

0.000001 V x 1,000,000 = 1 μV

Either way, we get the same answer of 1 microvolt.

Learn more about conversion factor here:

https://brainly.com/question/23510660

#SPJ11

The true statements about the Hubble Extreme Deep Field image are:

The Hubble Extreme Deep Field image is a testament to the immense scale and diversity of our universe. By capturing thousands of galaxies at various stages of development, the XDF allows astronomers to study the intricate processes of galaxy formation and evolution, ultimately enhancing our understanding of the cosmos.

The Hubble Extreme Deep Field (XDF) image is a remarkable snapshot of our universe, showcasing the farthest and most diverse celestial objects. This image contains approximately 5,500 galaxies, with some dating back to just 450 million years after the Big Bang. The XDF is a combination of observations taken by the Hubble Space Telescope over a period of ten years, focusing on a small region of the sky.

The XDF's depth and clarity reveal a wealth of information about the galaxies present in the image. Observing galaxies at different stages of development helps astronomers understand the processes involved in galaxy formation and evolution. The image contains a mix of spiral, elliptical, and irregular galaxies, each with their unique characteristics and histories.

Furthermore, the XDF highlights the vast scale of the universe, as many of the galaxies captured in this image are billions of light-years away from Earth. This vast distance means that the light we see from these galaxies started its journey billions of years ago, providing us with a glimpse into the universe's distant past.

For more such questions on Hubble Extreme Deep Field.

https://brainly.com/question/29740244#

#SPJ11

Complete Question:

Consider the first image shown in the video, which is the Hubble Extreme Deep Field. Which of the following statements about this image are true? Select all the true statements. The galaxies in this image are part of a large galaxy cluster, bound together by gravity. Careful study of the image shows that the youngest galaxies were mostly irregular in shape. We see the more distant galaxies as they were when they were quite young. ООО Careful study of the image shows that all present-day galaxies are spirals. The image includes galaxies that are elliptical, spiral, and irregular.

3Fd represents the change in the kinetic energy of the object. The correct option is A.

Kinetic energy is the energy possessed by a moving object. It is dependent on the object's mass and speed, with the formula for calculating kinetic energy being KE=1/2mv^2, where KE is kinetic energy, m is mass, and v is velocity. This energy can be transferred to other objects or converted into other forms of energy.

Options B, C, and D are not true because they involve multiplication by a factor greater than 3, which would result in a change in kinetic energy greater than what is possible based on the graph. The change in kinetic energy is equal to the area under the curve of the force vs. position graph. Since the graph only covers a distance of 3d, the maximum possible area under the curve is 3Fd, making option A the correct expression.

Therefore, The correct option is option A: 3Fd.

To learn more about Kinetic Energy click:

brainly.com/question/26472013

#SPJ1

The reasons of not having same time is, we can not hold the toy exactly at the same distance, it always get changes if our hand is trebling, if there is temperature difference in the room then also there is different time that can be taken by the air to travel, temperature difference of the two regions can influence the speed of the air. another reason is that for this toy we have pump the air from this toy and each time pumping pressure that we apply to this toy is not same. to have it same pressure we have to use machine.

If we draw distance on y axis and time on x axis then its slop gives the velocity of that object, hence teacher has told him to draw like this.

In ordinary language and kinematics, an object's speed is defined as the magnitude of its distance change over time or the magnitude of its position change per unit of time; it is therefore a scalar number.

To know more about Speed :

https://brainly.com/question/28224010

#SPJ1.

While enthalpy, internal energy, and work are all state functions, entropy is not. The correct answer is d. entropy.

For more such question on entropy

https://brainly.com/question/6364271

#SPJ11

If an ammeter is connected to an external circuit in such a way that the external current flow goes into the positive terminal of the meter, then the display is positive.

Ammeters are designed to measure the flow of electrical current in a circuit and the positive terminal of the meter is connected to the circuit's source of electrical power. When the current flows into the positive terminal of the ammeter, it travels through the meter and is measured by the device. The meter's display will then indicate the magnitude of the current flow in amperes. It's worth noting that the external circuit's current flow direction is not the same as the direction of the current flow through the meter. The current flow direction through the meter is indicated by the orientation of the meter's positive and negative terminals.

Therefore, the answer to the question is B) the display is positive. The ammeter measures the electrical current flowing through the external circuit, and the display shows the magnitude of the current flow in amperes.

To learn more about current flow here :

https://brainly.com/question/21660830

#SPJ11

Answer:

We can use the formula for the magnetic force on a wire:

F = BIL sin(theta)

Where:

F = magnetic force on the wire = 2.25 N

B = magnetic field strength = 1.2 T

I = current in the wire = 8.2 A

L = length of the wire segment = 47 cm = 0.47 m

We can rearrange this formula to solve for the angle theta:

theta = sin^(-1)(F / BIL)

Substituting the given values:

theta = sin^(-1)(2.25 N / (1.2 T * 8.2 A * 0.47 m))

theta = sin^(-1)(0.331)

theta = 19.5 degrees

Therefore, the angle between the wire carrying the current and the magnetic field is approximately 19.5 degrees.

Explanation:

Mechanical equilibrium refers to a state in which a body is not experiencing any acceleration, meaning it is either at rest or moving at a constant velocity.

In order to achieve this state, the sum of the external forces acting on the body must be equal to zero. This means that all the forces acting on the body must be balanced and cancel each other out, resulting in no net force.

Additionally, the sum of the external torques acting on the body must also be equal to zero. Torque is a measure of rotational force and determines how much an object will rotate when subjected to a force.

Therefore, for a body to be in mechanical equilibrium, the forces acting on it must not only balance out, but the torques acting on it must also be balanced.

It's important to note that even if a body is being moved by a constant force, it can still be in mechanical equilibrium if the sum of the external forces acting on it is zero. This is because the constant force is countered by an equal and opposite force, resulting in a net force of zero.

Overall, mechanical equilibrium is a crucial concept in physics that helps us understand how objects behave when subjected to external forces.

To know more about Mechanical equilibrium refer here:

https://brainly.com/question/14246949#

#SPJ11

A) The gravitational potential energy of the bungee jumper, when he stands on the bridge, is 127,400 J.

B) The jumper will have zero kinetic energy before the cord starts stretching.

C) Since the jumper starts with zero kinetic energy, he will not be moving before the cord starts stretching.

D) The bridge must be at least 62 meters tall for the jumper to avoid hitting the ground.

E) Even though energy is conserved, the jumper doesn't return to the bridge because the bungee cord converts the potential energy of the jumper into elastic potential energy stored in the cord as it stretches. This energy is then released as kinetic energy that propels the jumper upwards, and the cycle continues until the energy is dissipated due to air resistance and other factors.

A) The gravitational potential energy of the bungee jumper, when he stands on the bridge, can be calculated using the formula PE = mgh, where m is the mass of the jumper, g is the acceleration due to gravity (9.81 m/s²), and h is the height of the jumper above some reference level.

In this case, the reference level can be taken as the ground, so h = 20 + 2 = 22 m (taking the height of the jumper into account). Therefore, PE = (65 kg)(9.81 m/s²)(22 m) = 127,400 J.

B) Before the cord starts stretching, the jumper is stationary and therefore has zero kinetic energy.

C) The kinetic energy of the jumper can be calculated using the formula KE = (1/2)mv², where m is the mass of the jumper and v is the velocity of the jumper. Since the jumper has zero kinetic energy before the cord starts stretching, his velocity at this time is also zero.

D) The maximum length of the cord, when it is fully stretched, is 3 times the original length, which is 60 m. To avoid hitting the ground, the jumper must stop before the cord reaches its fully stretched length.

Using conservation of energy, the maximum height the jumper can reach is given by PE = (1/2)kx², where k is the spring constant of the bungee cord and x is the maximum stretch of the cord. Solving for x, we get x = sqrt(2PE/k) = sqrt(2mgh/k). Plugging in the numbers, we get x = sqrt((2)(65 kg)(9.81 m/s²)(62 m)/(50 N/m)) = 46.8 m.

Therefore, the bridge must be at least 62 m tall (20 m + 2 m + 46.8 m) for the jumper to avoid hitting the ground.

E) The bungee cord converts the potential energy of the jumper into elastic potential energy stored in the cord as it stretches. This energy is then released as kinetic energy that propels the jumper upwards. The cycle continues until the energy is dissipated due to air resistance and other factors. Therefore, the jumper doesn't return to the bridge.

To know more about gravitational potential energy refer here:

https://brainly.com/question/19768887#

#SPJ11

The ball will continue in a straight line tangent to its path. After the string breaks, the steel ball will continue to move tangentially to its path at the moment of breakage, due to its inertia. This means that the ball will follow a straight-line trajectory.

From an overhead perspective, the ball will continue moving in a straight line that is tangent to the circular path it was previously following.

This is because there are no forces acting on the ball in the horizontal plane to alter its motion.

Therefore, the correct path for the ball after the string breaks would be a straight line that is tangential to the point where the string broke.

It is important to note that air resistance and other external factors may affect the ball's trajectory to some extent, but in the absence of such forces, the ball will continue moving in a straight line.

For more such questions on trajectory, click on:

https://brainly.com/question/88554

#SPJ11